FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: mark w

Page 1 of 6 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    95
    Views
    3,677

    [General] no, and no. Its whats in the service manual. ...

    no, and no.

    Its whats in the service manual.

    also, you need to tighten the two longer bolts from the bottom first, then the ones around the flange.
  2. Replies
    95
    Views
    3,677

    [General] the backing plate should be sealed with hylomar...

    the backing plate should be sealed with hylomar on the vertical surface and with anerobic sealant on the bottom edge. the bottom edge is critical for aligment on the driveshaft, so that the seal is...
  3. Thread: Stock Exhaust

    by mark w
    Replies
    3
    Views
    417

    [For Sale] Interested and you have a PM

    Interested and you have a PM
  4. Replies
    13
    Views
    951

    I know of a car in NORCAL that's for sale. Pm me...

    I know of a car in NORCAL that's for sale. Pm me

    Blk interior
    Manual trans
    Wide stripe
    36k miles
    Very clean
    May 81 vin
  5. Replies
    95
    Views
    3,677

    [General] when you soda blasted the transmission case, did...

    when you soda blasted the transmission case, did you plug the vent hole?
  6. Replies
    13
    Views
    577

    [Engine] due to the rust buildup visible from those holes...

    due to the rust buildup visible from those holes Id say you should expect to replace the steel liners (which caused the rust) too, which then means its full rebuild time.
  7. [Brakes] you should not need to replace anything. you need...

    you should not need to replace anything. you need to get the adjuster tube/nut thing inside the level on the inner arm back in alignment with the hole. its loose inside there, but held by a small...
  8. Replies
    10
    Views
    1,304

    [For Sale] Ill take the two lower muffler brackets together...

    Ill take the two lower muffler brackets together for $40

    Mark
  9. Replies
    8,191
    Views
    1,405,441

    [General] assembled my engine today ...

    assembled my engine today
    ...
  10. NCDMC- March 7 event to visit Stanford - and the drifting Delorean

    this event March 7 2020 9am to 2pm

    we will meet at starbucks at 9am and then drive as a group to Stanford where the Dynamic Design lab team will share with us their drifting Delorean project.
    ...
  11. Replies
    95
    Views
    3,677

    [General] i just refreshed my transmission replaced the 2nd...

    i just refreshed my transmission replaced the 2nd gear pin and red loctited the two big nuts on the end.

    if you are pulling the transmission.....and these two things have not yet been done- then...
  12. Replies
    8,191
    Views
    1,405,441

    [General] i started to re-assemble my 5 spd transmission ...

    i started to re-assemble my 5 spd transmission

    6242662427
  13. Replies
    5
    Views
    518

    [Wanted] where.....

    where.....
  14. [Wanted] want to buy- Washer reservoir cover part 106087

    Want to buy, a used washer reservoir tank cover. the one that mounts in the front left corner, from below, forward of the front wheel. Mine is cracked in several places and I dont want to pay $100...
  15. Replies
    5
    Views
    422

    [Engine] i have some PRV heads from a turbo motor that are...

    i have some PRV heads from a turbo motor that are double springs with custom isky cams. I have no idea what they are tho. id sell the whole setup
  16. Replies
    2
    Views
    342

    [General] um.... ...

    um....

    http://dmctalk.org/showthread.php?12661-You-built-an-electric-self-driving-drifting-car-out-of-a-DeLorean&highlight=marty
  17. [General] the upper and lower A arms were fabricated by the...

    the upper and lower A arms were fabricated by the team. the frame section that the A arms attach too is stock, but missing the crumple section forward of the tunnel that the steering rack normally...
  18. Thread: Door hinge

    by mark w
    Replies
    4
    Views
    632

    [Frame & Body] DPI makes them in stainless.

    DPI makes them in stainless.
  19. Replies
    4
    Views
    384

    [Engine] the pipes that run next to the fuel tank just sit...

    the pipes that run next to the fuel tank just sit in there, there should be some foam blocking in around them, now kinda triangle shaped. drop the tank and the pipes fall out. I just did this on my...
  20. Replies
    25
    Views
    1,253

    [Engine] AH, i see. I removed my pump, but didnt take it...

    AH, i see. I removed my pump, but didnt take it apart that far.
  21. Replies
    25
    Views
    1,253

    [Engine] there is no spring in the oil pump, nor a cotter...

    there is no spring in the oil pump, nor a cotter pin.
    to remove it, its three bolts, AFTER you have removed the timing cover and the Pulley.
  22. Where is this car?

    Where is this car?
  23. Thread: Liner Seals

    by mark w
    Replies
    69
    Views
    4,139

    [Engine] id call all the dmc techs around and ask them.

    id call all the dmc techs around and ask them.
  24. Thread: Liner Seals

    by mark w
    Replies
    69
    Views
    4,139

    [Engine] I think these "seals" are not seals at all,...

    I think these "seals" are not seals at all, originally they are made from several thicknesses of paper with different color tabs for different thicknesses, and 40 year old paper at that. They act as...
  25. Replies
    2
    Views
    610

    edit title: photo contest! (but really only for...

    edit title:
    photo contest! (but really only for Florida owners}
Results 1 to 25 of 136
Page 1 of 6 1 2 3 4