FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: dn010

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Thread: No Start

    by dn010
    Replies
    13
    Views
    369

    [Fuel] That post was intended for David.

    That post was intended for David.
  2. Thread: No Start

    by dn010
    Replies
    13
    Views
    369

    [Fuel] Did you happen to maybe miss post #8 where I...

    Did you happen to maybe miss post #8 where I already said all of this?
  3. Thread: No Start

    by dn010
    Replies
    13
    Views
    369

    [Fuel] A possibility for you taillight issues, those...

    A possibility for you taillight issues, those bulkhead connectors are shit in my opinion. They gave me nothing but random electrical problems with the engine and many problems with the taillights...
  4. Replies
    0
    Views
    106

    [For Sale] Steering U-Joints-Stock

    I have stock upper and lower steering u-joints/shaft part #s 100839 & 100840. They don't seem to have any play when I try to turn them by hand. I don't recall where I got them, how long I've had them...
  5. [Engine] I donít know this product but am always hesitant...

    I donít know this product but am always hesitant of a miracle in a bottle unless itís a last resort.
  6. [Engine] Or, another cause is when the seal creates a...

    Or, another cause is when the seal creates a groove in your crankshaft surface which will cause a leak even with a new seal being installed over it. I found that after some measuring where the groove...
  7. Replies
    29
    Views
    1,072

    [General] I don't see that your rear main questions where...

    I don't see that your rear main questions where addressed. You shouldn't have to drain the oil to change the seal. Make sure the new seal comes with the gasket for the plate the seal rides in. When...
  8. Replies
    29
    Views
    1,072

    [General] When cold, it would either not go into gear or...

    When cold, it would either not go into gear or grind terribly, so much that I would skip 2nd gear altogether it was that bad. When everything was warm I would still sometimes have an issue...
  9. Replies
    29
    Views
    1,072

    [General] I also had issues with 2nd gear. I replaced the...

    I also had issues with 2nd gear. I replaced the roll pin because I was in the transmission at one time fixing some other damaged items. However my issues remained. It wasn't until I installed a new...
  10. Thread: Low oil pressure

    by dn010
    Replies
    13
    Views
    852

    [Engine] You are forgetting about the spring in the oil...

    You are forgetting about the spring in the oil pump as being a possible culprit as well, I'd check that first before separating the block from the lower crankcase.
  11. [General] Meanwhile, CA still has the highest amount of air...

    Meanwhile, CA still has the highest amount of air pollution in the US.
  12. Thread: B280e

    by dn010
    Replies
    3
    Views
    519

    [For Sale] What would you let the cams go for, and do you...

    What would you let the cams go for, and do you have the balancing shaft?
  13. Replies
    4
    Views
    515

    [Wanted] The stock exhaust uses manifolds, not headers.

    The stock exhaust uses manifolds, not headers.
  14. Thread: Cam timing

    by dn010
    Replies
    10
    Views
    536

    [General] Best to just go directly to the source. Email...

    Best to just go directly to the source. Email Josh.
  15. Thread: Cam timing

    by dn010
    Replies
    10
    Views
    536

    [General] I'm not sure if you're being sarcastic or not but...

    I'm not sure if you're being sarcastic or not but the link is to the workshop manual along with other manuals that are very helpful. OP -Go into the manual, print out the procedure and have it in...
  16. Thread: Cam timing

    by dn010
    Replies
    10
    Views
    536

    [General] http://dmctalk.org/showthread.php?2866-Searchable-...

    http://dmctalk.org/showthread.php?2866-Searchable-Workshop-Technical-Bulletins-and-Volvo-Engine-Manuals
  17. Replies
    16
    Views
    1,677

    First few times I did this, I used 4X4 blocks of...

    First few times I did this, I used 4X4 blocks of wood to hold up the body in the air - wasn't really the safest. The latest time I used a bunch of cinder blocks. As mentioned, if they are damaged in...
  18. Replies
    36
    Views
    2,960

    I still haven't completed a permanent air filter...

    I still haven't completed a permanent air filter setup for my EFI conversion. My filter currently sits above the exhaust by the expansion tank - pretty awful since it's sucking in all that hot air...
  19. Replies
    133
    Views
    21,020

    [General] You've already spelled it out, twice now....

    You've already spelled it out, twice now. However, I'm confused:
  20. Thread: Oil Pump Spring?

    by dn010
    Replies
    25
    Views
    1,191

    [Engine] Oil Pump Spring?

    Like Ron stated, the valve does not regulate pressure. It only opens at a certain PSI to bleed high pressure. This argument doesnít really matter since regardless, there are no springs available for...
  21. Replies
    56
    Views
    9,931

    My reman starter would also clank repeatedly,...

    My reman starter would also clank repeatedly, started with once in a while to about 5-10 times turning the key until it would actually engage. Turned out to be a loose ground for me, maybe this is...
  22. Thread: Oil Pump Spring?

    by dn010
    Replies
    25
    Views
    1,191

    [Engine] I should specify that I'm talking about the Volvo...

    I should specify that I'm talking about the Volvo B280F pump springs that were broken.

    Unfortunately I have not found anywhere to get replacements so I have a few pumps laying around. These pumps...
  23. Thread: Oil Pump Spring?

    by dn010
    Replies
    25
    Views
    1,191

    [Engine] The Volvo springs are shit. Two of the three...

    The Volvo springs are shit. Two of the three pumps I took apart had broken springs. The spring in the D seems to be better made than those.
  24. Replacing bunch of Alternator Wires for larger 4 gauge Single wire cable?

    Yes, I removed the brown wires and ran a battery cable from the alternator to the bulkhead. The brown wires were very corroded and this was my best option. I ran the wire down the pontoon instead of...
  25. Replies
    13
    Views
    884

    [Transmission 5-Speed] Your guess is inaccurate. It's really not that...

    Your guess is inaccurate. It's really not that hard to remove a fitting, put your finger over the drain hole and then quickly swap your finger for the drain plug. You will lose some fluid but you...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4