Search:

Type: Posts; User: dmcnc

Page 1 of 3 1 2 3

Search: Search took 0.05 seconds.

  1. Thread: Alternator help

    by dmcnc
    Replies
    9
    Views
    210

    [Electrical] It's definitely a Saturn Alternator. DMCH sells a...

    It's definitely a Saturn Alternator. DMCH sells a similar CS-130 style alternator with a slightly different "iceberg" shell that matches the OEM bracket.
    - You can use the stock bracket with this...
  2. Replies
    13
    Views
    420

    [Fuel] Yes! I thought the same: just beautiful!!

    Yes! I thought the same: just beautiful!!
  3. Replies
    15
    Views
    579

    [Engine] I also had pretty bad misfiring kicking in over...

    I also had pretty bad misfiring kicking in over the past week or so after the big storm that swept through the Southeast. I found and corrected two issues:
    1. Cylinder # 6 was full of water. Dried...
  4. Replies
    8
    Views
    466

    [Frame & Body] Seems to me your struts are also not set to your...

    Seems to me your struts are also not set to your current torsion bar setting. I had that same issue with stabilus struts - some of them were too weak (opened 2/3 of the way), others slammed the doors...
  5. Replies
    14
    Views
    791

    [General] Definitely interested. My otterstat is failing...

    Definitely interested. My otterstat is failing intermittently and Toby's solution has been out of stock for a while.
  6. Replies
    22
    Views
    1,637

    [General] Not disagreeing with you at all, David -...

    Not disagreeing with you at all, David - everything you said is very likely if anything. That said, from their last update in October 2016:

    "As mentioned before, while the legislation that allows...
  7. Replies
    22
    Views
    1,637

    [General] My best guess is they're stalling based on...

    My best guess is they're stalling based on uncertainty from lack of further legislation / rulemaking for the implementation of low-volume vehicle manufacturing according to their last update. Perhaps...
  8. Replies
    2
    Views
    258

    [Frame & Body] It might sound obvious, but I've been there!!!

    It might sound obvious, but I've been there!!!
  9. Replies
    371
    Views
    33,894

    Amazing work, Rich! I'll have to ping you later...

    Amazing work, Rich! I'll have to ping you later for more details :)
  10. Replies
    371
    Views
    33,894

    Are you able to keep the stitching silver or does...

    Are you able to keep the stitching silver or does it blend in with the dye?
  11. Replies
    220
    Views
    38,705

    Where did you track down a new canopy? :wow:

    Where did you track down a new canopy?
    :wow:
  12. [Fuel] I'd do two things: Check the gas tank around...

    I'd do two things:

    Check the gas tank around the fuel pump seal for leaks (gas smell issue) and check if your CSV is firing during hot starts. Once the engine is hot turn the engine off, unscrew...
  13. Replies
    2
    Views
    518

    [General] Thank you for this. Had this very same issue...

    Thank you for this. Had this very same issue recently, and I was able to unlock it as you said.
  14. [Fuel] CSV should always be plugged in, otherwise you'll...

    CSV should always be plugged in, otherwise you'll have a hard time getting it started when cold. The question is, what flooded your car? If the CSV is open beyond the initial cold crank then you have...
  15. [Fuel] No worries, yes step on the gas and leave it...

    No worries, yes step on the gas and leave it pressed for a bit. Hopefully some of that gas will have evaporated and made its way out by now.
  16. [Fuel] I'd unplug the Cold Start Valve, open the...

    I'd unplug the Cold Start Valve, open the throttle for a minute or so, and crank again. Otherwise you could run down this troubleshooting guide:...
  17. [General] Legal :D

    Legal :D
  18. Thread: is this fixable?

    by dmcnc
    Replies
    12
    Views
    763

    [General] Yes - the attached PDF might be of help. 49247

    Yes - the attached PDF might be of help.

    49247
  19. Replies
    12
    Views
    606

    [Fuel] Nice! Let us know how it goes!

    Nice! Let us know how it goes!
  20. Replies
    4
    Views
    266

    [Frame & Body] They do, I know that's what the vendors use...

    They do, I know that's what the vendors use whenever they're redying Delorean interiors.
  21. Replies
    4
    Views
    266

    [Frame & Body] You contact Leatherique and specifically request...

    You contact Leatherique and specifically request Delorean gray for your dye.
    http://www.leatherique.com

    Otherwise, Dave G. may have some SEM Acura 17333 cans left:...
  22. Replies
    11
    Views
    898

    [Frame & Body] For those seriously interested, please PM Rob at...

    For those seriously interested, please PM Rob at PJ Grady as he would be the man putting the trip together. :)
  23. Thread: VIN Chronology

    by dmcnc
    Replies
    419
    Views
    71,962

    4285 is now in Destin, Florida

    4285 is now in Destin, Florida
  24. Replies
    16
    Views
    1,276

    [Frame & Body] I'm fairly certain this is the same car that...

    I'm fairly certain this is the same car that caught fire damage a few months ago.
    ...
  25. Replies
    11
    Views
    898

    [Frame & Body] Chris Nicholson in Florida

    Who would be interested in bringing Chris Nicholson to Florida? Chris' mastery on stainless is second to none, and I'm inspired with how the Aussies were able to sponsor a regraining tour down under....
Results 1 to 25 of 74
Page 1 of 3 1 2 3