FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: 81dmc

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Thread: Door alignment

    by 81dmc
    Replies
    8
    Views
    407

    [Frame & Body] No, you need to keep the outer seals off so you...

    No, you need to keep the outer seals off so you can adjust the panels afterwards.


    You need to install the inner door seals.



    When I said “weather stripping” above, I was referring to the...
  2. Thread: Door alignment

    by 81dmc
    Replies
    8
    Views
    407

    [Frame & Body] Just tweaked my drivers door a little a few days...

    Just tweaked my drivers door a little a few days ago to close a huge gap between it and the A pillar. I never adjusted that gap when I installed a new door in 2015.

    Steps I do:

    1.) Remove...
  3. Replies
    25
    Views
    1,496

    63919 Circled in red is the useless dumb...

    63919

    Circled in red is the useless dumb distributor. Youíll need to cap that hole.



    Looks like a nice engine unlike the one I bought. Mine looked like it was on a shelf since the 90s....
  4. Replies
    25
    Views
    1,496

    I got an early engine. That distributor is a...

    I got an early engine. That distributor is a ďdumbĒ distributor with no advance. It relies on factory eagle ecu which is not worth anyoneís time.

    Now you could retrofit a traditional distributor...
  5. Replies
    25
    Views
    1,496

    You will need EDIS6. 2.8 PRV is odd fire with...

    You will need EDIS6.

    2.8 PRV is odd fire with traditional distributor. 3.0 PRV is even fire without traditional distributor.
  6. Replies
    25
    Views
    1,496

    Havenít gotten there yet. Still waiting on new...

    Havenít gotten there yet. Still waiting on new liners from the UK.

    Once the engine is built and installed, Iíll do some decision making in the controls. I am heavily leaning towards Microsquirt...
  7. Replies
    43
    Views
    4,764

    [Electrical] If you had the issue before with incandescents,...

    If you had the issue before with incandescents, check your tail light circuit board. You may need a newer updated one. Also check the tail light plug for corrosion, and check the black connector at...
  8. [For Sale] Sold! Please close thread.

    Sold!

    Please close thread.
  9. [General] Off topic, but I just realized with that Jack pic...

    Off topic, but I just realized with that Jack pic that he has censored his VIN on here, but he freely posts pics of his N-number...
  10. Thread: The TesLorean

    by 81dmc
    Replies
    101
    Views
    30,284

    [General] Nice design... lol Really want to see this...

    Nice design... lol


    Really want to see this car drive, good work!
  11. [General] 63756

    63756
  12. [For Sale] Bump. Price now $180 shipped.

    Bump.

    Price now $180 shipped.
  13. Thread: annoying buzzer

    by 81dmc
    Replies
    108
    Views
    21,985

    [General] I have the Jeep chime module in my DeLorean with...

    I have the Jeep chime module in my DeLorean with the factory Jeep connector wired in. Only reason I was able to do that years ago was this thread.


    However now that this thread has been revived,...
  14. Replies
    33
    Views
    2,299

    [Fuel] Mine. Knock on wood...

    Mine.

    Knock on wood...
  15. Replies
    33
    Views
    2,299

    [Fuel] I like the metal top of that pump. Iíll...

    I like the metal top of that pump. Iíll personally go this route if I ever need to replace the pump.
  16. Replies
    33
    Views
    2,299

    [Fuel] Wow. Hopefully mine still works when I finish my...

    Wow. Hopefully mine still works when I finish my project. It has a 2013 pump, and it was working fine when parked in 2018.

    Did they switch to a lower quality setup sometime after 2013?
  17. Replies
    6
    Views
    430

    [Engine] This is a Z7X 3.0 engine. The factory 3.0 liners...

    This is a Z7X 3.0 engine. The factory 3.0 liners on my engine are all 1 notch which mean 93.00-93.01mm bore.

    I decided to place an order with Westwood liners to get a set of six. Since the...
  18. Replies
    6
    Views
    430

    [Engine] Pitted Liners- Would you run them?

    63331
    63332

    Should I bother running these? The one in the attached pics is the worst, and two others have slightly less pitting. The other three are fine.

    Should I just contact Westwood to buy...
  19. Replies
    12
    Views
    638

    [Frame & Body] I just stuck angle drive caps in the holes with...

    I just stuck angle drive caps in the holes with RTV to seal.
  20. [For Sale] Set of 6 Used Injectors (New in 2014) with Braided SS Lines, Seals, and Clips.

    As the title says. The injectors and lines were new Bosch in 2014 and were running fine when pulled from my old engine. Seals were new in 2017. Clips are original, but good.

    63178

    $200
  21. [Frame & Body] AFAIK, there is none. It is riveted to door...

    AFAIK, there is none.

    It is riveted to door panel and is considered part of the lower panel assembly. You could probably ask DMCH if they have a spare peice from a broken panel.
  22. Replies
    29
    Views
    2,031

    [General] 63031

    63031
  23. Replies
    13
    Views
    1,111

    :vomit_1:

    :vomit_1:
  24. Replies
    26
    Views
    1,495

    [Fuel] 3 options to make a kjet equipped car safer: ...

    3 options to make a kjet equipped car safer:

    1.)Convert it to EFI
    2.)Convert it to carb
    3.)Engine delete (I did this and my car has been trouble free for a year!)


    :neener:You're paranoid.
  25. Replies
    15
    Views
    692

    [General] Maybe I can send you my unit for testing? PM...

    Maybe I can send you my unit for testing? PM address if you want.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4