FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.24 seconds.

  1. If you adjust the mixture richer you will get...

    If you adjust the mixture richer you will get more power.
  2. [Electrical] Wiggle all the wires while the door is open so...

    Wiggle all the wires while the door is open so you can see if there is a marginal connection. Sometimes those crimps with two wire in one pin go bad. It sounds like you lost the purple wire...
  3. [Electrical] Sorry. I was looking at glove box switch. The...

    Sorry. I was looking at glove box switch. The LH switch does show purple/blue and the RH switch is purple/pink.

    You would normally see 12 volts on the switch wires if not grounded by the switch....
  4. [Electrical] Purple/blue goes to the buzzer. Door light...

    Purple/blue goes to the buzzer. Door light switch should be purple/white.
  5. Replies
    20
    Views
    366

    [Electrical] I had a few cars where there is a battery cover...

    I had a few cars where there is a battery cover and then you would forget to add water (yes the ones with the three cell covers do loose water). Forgot that for a few batteries and then said have to...
  6. Replies
    20
    Views
    366

    [Electrical] Last time I was getting tires and waiting I saw...

    Last time I was getting tires and waiting I saw all they had were interstate batteries and non were sealed. So I guess they get these really cheap so they charge the going battery rate and still...
  7. Replies
    53
    Views
    1,191

    [General] Air flow into the engine pushes the plunger in....

    Air flow into the engine pushes the plunger in. Fuel pressures do not push it in.
  8. Replies
    20
    Views
    366

    [Electrical] Interstate does not carry many sealed batteries...

    Interstate does not carry many sealed batteries (at my tire stores or garages). I usually buy the least expensive sealed battery at Walmart or Sears.
  9. Replies
    50
    Views
    1,512

    [General] I think most of us that have been in a parade...

    I think most of us that have been in a parade drive it with the doors open. So a paved road at 5 MPH is probably safe.
  10. Replies
    169
    Views
    20,722

    Like always the photo just can not get the true...

    Like always the photo just can not get the true colors of LEDs. I do see I need to fix the small green dot above and to the right of "MAX". I also want to look into covering the two push button...
  11. Replies
    169
    Views
    20,722

    So what kind of plastic do you think the OEM...

    So what kind of plastic do you think the OEM faceplate was made of? I just ordered some ABS filament to try another HVAC face plate made with that. ABS works to higher temps than PLA.
  12. Replies
    169
    Views
    20,722

    Decal Alignment

    Alignment cylinders worked out perfect. These are 1.416" dia. which makes it snug on the DMCH decal. My printed faceplate I made the holes 0.010 smaller so I could sand them on my oscillating drum...
  13. Replies
    169
    Views
    20,722

    Trying to get something engineered so I can place...

    Trying to get something engineered so I can place the decal exactly in the correct position. I can only think of using the two push button holes for alignment. The holes in the decal are 1.420" so...
  14. Replies
    20
    Views
    628

    [Fuel] You won't be able to buy acetone in California.

    You won't be able to buy acetone in California.
  15. Replies
    56
    Views
    5,294

    [General] Yes the OEM pins are not really interchangeable...

    Yes the OEM pins are not really interchangeable with the AMP connector. My pin extractor does not work with the AMP pins.
  16. Replies
    169
    Views
    20,722

    Well I'm going with the idea to print the HVAC in...

    Well I'm going with the idea to print the HVAC in black and have made cutouts for the decal illumination areas. It would probably work without filling those cutouts with clear epoxy. The stock face...
  17. [Suspension] It looks like only 0.028" difference so I would...

    It looks like only 0.028" difference so I would think the casing is still there.
  18. [Suspension] Did you check if the old one has been bent out of...

    Did you check if the old one has been bent out of round. Measure it at 90 degrees from the first measurement.
  19. Replies
    5
    Views
    256

    [General] Yes the inertia switch is what I mean. The door...

    Yes the inertia switch is what I mean. The door lock ECU is a black box (if stock) mounted on the relay compartment metal plate. It has a 9 pin connector on wires to that black box.
  20. Replies
    5
    Views
    256

    [General] If your impact sensor is triggered it will unlock...

    If your impact sensor is triggered it will unlock if you have the door lock ECU installed.
  21. Replies
    169
    Views
    20,722

    I did get that clear filament and printed an HVAC...

    I did get that clear filament and printed an HVAC panel. Only real problem was that 0.71 deg offset from square so the two standoffs are offset to much. I'm not sure if the clear will block the...
  22. Replies
    169
    Views
    20,722

    Ran into another problem. My 4 corner standoffs,...

    Ran into another problem. My 4 corner standoffs, the top 2 were shifted to the right. Checked my design a 100 times and then thought to use a square to check the print. The print is not printing...
  23. Replies
    169
    Views
    20,722

    Thanks. I plan to test to 140 F or above.

    Thanks. I plan to test to 140 F or above.
  24. Here is a interesting tidbit of info. Well after...

    Here is a interesting tidbit of info. Well after about a week with it holding around 44 PSI, I released the pressure and it leaked out the gas pretty slowly (about 30 seconds). I could also hear...
  25. Replies
    169
    Views
    20,722

    There is no mechanical needs for the HVAC. Just...

    There is no mechanical needs for the HVAC. Just my concern is the bond between the decal and faceplate. I do plan to try PETG and ABS to play with. What do you think the max temp inside the cabin...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4