FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Ron

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    12
    Views
    182

    [Electrical] You are reading it right. (Easy to see- If you...

    You are reading it right.
    (Easy to see- If you unplug the double PK wires from your blue diode, the 3 passenger lights will work and the interior light will not.)


    Sounds like the P/PU wires...
  2. Thread: Introductions!

    by Ron
    Replies
    725
    Views
    249,741

    Sticky: :welcome:

    :welcome:
  3. Replies
    12
    Views
    182

    [Electrical] I'm thinking you are both correct- The WSM...

    I'm thinking you are both correct-
    The WSM schematic shows two left door switches. Both numbered 41. Both have Purple/Blue wires, which do not tie together.:swear1:

    Could you have mixed them...
  4. Replies
    20
    Views
    367

    [Electrical] +1 for Delco (best bang for bucks, imho). Good...

    +1 for Delco (best bang for bucks, imho).

    Good link about batteries HERE.
  5. Replies
    53
    Views
    1,191

    [General] No, a clogged WUR/CPR screen will cause the...

    No, a clogged WUR/CPR screen will cause the control pressure to be too strong:
    The primary pressure from within the FD is applied to the plunger, pushing it down. The WUR/CPR bleeds off that...
  6. [Engine] Not for a DeLorean, but you can get the idea:...

    Not for a DeLorean, but you can get the idea:
    65727
    They are only needed if the pulley's mating surface for the seal has been damaged causing an oil leak (usually from dirt cutting a groove).

    A...
  7. Replies
    53
    Views
    1,191

    [General] I was going to say make one, if the old line...

    I was going to say make one, if the old line going from the FD to the CPR/WRU was ok...I thought you said you were retired...:deviltail:
  8. Replies
    53
    Views
    1,191

    [General] Yeah ~1.0Ω Most of the gauges I've seen read 1/4...

    Yeah ~1.0Ω
    Most of the gauges I've seen read 1/4 @ idle then almost max out quickly.

    Time for the fuel pressure gauge, imho.
  9. Replies
    50
    Views
    1,513

    [General] Got ya. ...but time has nothing to do with it,...

    Got ya. ...but time has nothing to do with it, assuming it could handel 88 MPH. :)
  10. Replies
    50
    Views
    1,513

    [General] Curious as to why you think this??

    Curious as to why you think this??
  11. Thread: R12 ac?

    by Ron
    Replies
    16
    Views
    425

    [Heat & A/C] I think you meant compressor. ====== ...

    I think you meant compressor.

    ======

    Changing over means a full flush, different oil, and a new accumulator (some say hoses too).
    I doubt you'll like the results in FL.
  12. Thread: R12 ac?

    by Ron
    Replies
    16
    Views
    425

    [Heat & A/C] Expect higher pressures and lower performance...

    Expect higher pressures and lower performance with 134a.

    Maybe this link?:
    http://dmctalk.org/showthread.php?15344-How-To-Diagnosing-and-bulletproofing-your-A-C
  13. Replies
    53
    Views
    1,191

    [General] This guy 65683. It's in the center bore (see...

    This guy 65683. It's in the center bore (see arrow):

    65684
    (Your's may not have the retainer.)
  14. Replies
    53
    Views
    1,191

    [General] Correct. Could be the Fuel Distributor's...

    Correct. Could be the Fuel Distributor's (FD/mixture unit) plunger is stuck (...as said about the cat glowing earlier).

    The other end of each injector line is connected to the FD.
    I'd try...
  15. Replies
    50
    Views
    1,513

    [General] +1...with Mark's reply a close 2nd :):)

    +1...with Mark's reply a close 2nd :):)
  16. Replies
    50
    Views
    1,513

    [General] Probably not a good idea since it does say, "Do...

    Probably not a good idea since it does say, "Do not attempt to close the door by exerting pressure at the front edge as this could result in a ‘sprung’ door requiring adjustment and possible repair."...
  17. Replies
    50
    Views
    1,513

    [General] http://dmctalk.org/showthread.php?2755-DeLorean-Ow...

    http://dmctalk.org/showthread.php?2755-DeLorean-Owner-s-Handbook-Manual
  18. Replies
    8
    Views
    294

    [Wanted] When I first read the thread, there were three...

    When I first read the thread, there were three replies (by two different members) not meeting the rules. As I said before, I would of ignored them but one pointed to a damaged frame on eBay, one...
  19. Replies
    8
    Views
    294

    [Wanted] Mike changed the rules because the section was...

    Mike changed the rules because the section was being plagued with attacks against other members and/or their items, the resulting banter from other members, and to cut down on annoying notifications...
  20. Replies
    8
    Views
    294

    [Wanted] You must of missed the part in bold saying,...

    You must of missed the part in bold saying, "Wanted- Do not post a question or remark if you do not intend to sell an item.", again.

    (If a reply in the Wanted section offers help, the rule is...
  21. Replies
    8
    Views
    294

    [Wanted] Missing a post? Please review the Stick at:...

    Missing a post?

    Please review the Stick at:
    http://dmctalk.org/showthread.php?18125-***-SECTION-RULES-***-Please-READ-BEFORE-POSTING-***
  22. Replies
    12
    Views
    640

    Seems I remember him lurking around then. :devil:...

    Seems I remember him lurking around then. :devil:

    ...After the BS FB has been pulling lately, I would boycott them, if I wasn't permabanned already.:)
  23. Thread: Hood release

    by Ron
    Replies
    10
    Views
    341

    [General] 65606 That end of the cable may have broken...

    65606

    That end of the cable may have broken off...its part number 106804 (or #36 in the first link Rich posted above).
  24. Replies
    12
    Views
    640

    :cheers1:

    :cheers1:
  25. Replies
    12
    Views
    451

    [Engine] I'm guessing you had the mode switch set to AC...

    I'm guessing you had the mode switch set to AC...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4