Search:

Type: Posts; User: Ron

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    22
    Views
    587

    [General] B/O going in and out of the breaker? EDIT: NM....

    B/O going in and out of the breaker?

    EDIT: NM.
    I did an image search for "fan circuit breaker" and most show N/O to Fan Relay and B/O to the Fan Fail. None with N/S like the WS manual.

    Best...
  2. Replies
    22
    Views
    587

    [General] Me? ...It's wired the same as the one I posted. ...

    Me? ...It's wired the same as the one I posted.
    J/K!
    =============================


    Ron, I think the first one IS ~DMC, remastered color...(How B/G got changed is a mystery ;-)
    It also has...
  3. Replies
    22
    Views
    587

    [General] Yep, your car's Black/Green is like the one I...

    Yep, your car's Black/Green is like the one I just posted. The last one you posted has a Black/Orange feeding the Fan Fail (not the breaker, which isn't shown...) instead of Brown/Slate.

    Where did...
  4. Replies
    22
    Views
    587

    [General] I've looked at A LOT of schematics and have never...

    I've looked at A LOT of schematics and have never seen it any other way than this:

    54637
    (Click to enlarge)
  5. Replies
    22
    Views
    587

    [General] AH, now we're onto something.... BRB...

    AH, now we're onto something....

    BRB...
  6. Replies
    22
    Views
    587

    [General] NP! ...you posted the meter and other end...I was...

    NP! ...you posted the meter and other end...I was hesitant to ask but ya never know...

    Did you know the schematic you posted above is not like stock?
  7. Replies
    22
    Views
    587

    [General] The connection near the washer bottle would be my...

    The connection near the washer bottle would be my guess for a bad connection causing it. But, like Dave,
    I'd eliminate the rest first...Maybe get a couple of straight pins and pierce the ends of...
  8. Replies
    34
    Views
    1,049

    [Electrical] We seem to have a communication problem...

    We seem to have a communication problem :deviltail: ...


    I would use the RPM relay because:
    ...and I don't see the circuit as being over stressed, else I would of added a relay to split the...
  9. Replies
    34
    Views
    1,049

    [Electrical] I think you meant "Blue/Purple"... That would be...

    I think you meant "Blue/Purple"...
    That would be good if you didn't mind the drain on the battery when you just wanted to run the radio or other accessory. I've used the override on my Silverado...
  10. Replies
    34
    Views
    1,049

    [Electrical] I think you might get DRLs by replacing the 2...

    I think you might get DRLs by replacing the 2 existing high beam only bulbs with 2 high-low bulbs, then feed the 2 extra terminals through a relay triggered by the RPM Relay's Hot When Engine...
  11. Replies
    34
    Views
    1,049

    [Electrical] I have NOT tried it, but it looks like you could...

    I have NOT tried it, but it looks like you could do it with 2 jumpers and a diode:
    Remove the Low Beam Relay's feed (30, N), feed it with a jumper from the High Beam Relay's center terminal (87a),...
  12. [Fuel] I have to ask... Why was the air filter off in...

    I have to ask...
    Why was the air filter off in the first place?? :deviltail:
  13. [Fuel] Agreed, it is just there to handle what does blow...

    Agreed, it is just there to handle what does blow by... If you haven't, actually try putting your palm on the bottom of the filler...it is very strong. If the blowby was anything close to keeping up...
  14. [Fuel] hehe..this has been hashed over before.. In...

    hehe..this has been hashed over before.. In short;
    The manual states, "The closed crankcase system does not have an air inlet for air circulation within the crankcase.This system applies manifold...
  15. [Fuel] Sorry for the confusion Robert... In the How To,...

    Sorry for the confusion Robert...
    In the How To, I included removing the breather because a lot of people have complained about reaching the adjusting screw with standard tools, some had non-stock...
  16. Replies
    8
    Views
    2,544

    I corrected information in the pic (Post #1) that...

    I corrected information in the pic (Post #1) that was causing some confusion.

    NOTE- If your D's plumbing is not stock (closed system), this How To Does Not Apply.
  17. Replies
    2
    Views
    219

    [General] Maybe this thread, but the panel was covered...

    Maybe this thread, but the panel was covered aluminum instead of SS
    http://dmctalk.org/showthread.php?8822-My-Custom-Centre-Console
  18. Replies
    13
    Views
    592

    [General] Under the console?? That sounds like an...

    Under the console?? That sounds like an improvement. lol
  19. Replies
    13
    Views
    592

    [General] fwiw, it is fed via Fuse 18, which should be live...

    fwiw, it is fed via Fuse 18, which should be live at all times.
  20. Replies
    13
    Views
    592

    [General] You can just jump the two wires going to the...

    You can just jump the two wires going to the switch together to check it..
  21. [For Sale] It's that favoritism thing. Now crawl back...

    It's that favoritism thing.

    Now crawl back into your mouse hole before I tell who/what used to keep hin warm...
  22. [For Sale] :hysterical: THX , I needed that!

    :hysterical:
    THX , I needed that!
  23. :thumbup:

    :thumbup:
  24. [For Sale] MPPDMC, I moderate this section and was...

    MPPDMC,
    I moderate this section and was considering saying something earlier but, because I saw you were new and to avoid cries of favoritism, I decided to wait and see where things went.

    You...
  25. Replies
    11
    Views
    721

    New Headlight Switch Instructions U/L in...

    New Headlight Switch Instructions U/L in Resources
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4