FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Ron

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    40
    Views
    994

    [General] +1...with Mark's reply a close 2nd :):)

    +1...with Mark's reply a close 2nd :):)
  2. Replies
    40
    Views
    994

    [General] Probably not a good idea since it does say, "Do...

    Probably not a good idea since it does say, "Do not attempt to close the door by exerting pressure at the front edge as this could result in a ‘sprung’ door requiring adjustment and possible repair."...
  3. Replies
    40
    Views
    994

    [General] http://dmctalk.org/showthread.php?2755-DeLorean-Ow...

    http://dmctalk.org/showthread.php?2755-DeLorean-Owner-s-Handbook-Manual
  4. Replies
    8
    Views
    271

    [Wanted] When I first read the thread, there were three...

    When I first read the thread, there were three replies (by two different members) not meeting the rules. As I said before, I would of ignored them but one pointed to a damaged frame on eBay, one...
  5. Replies
    8
    Views
    271

    [Wanted] Mike changed the rules because the section was...

    Mike changed the rules because the section was being plagued with attacks against other members and/or their items, the resulting banter from other members, and to cut down on annoying notifications...
  6. Replies
    8
    Views
    271

    [Wanted] You must of missed the part in bold saying,...

    You must of missed the part in bold saying, "Wanted- Do not post a question or remark if you do not intend to sell an item.", again.

    (If a reply in the Wanted section offers help, the rule is...
  7. Replies
    8
    Views
    271

    [Wanted] Missing a post? Please review the Stick at:...

    Missing a post?

    Please review the Stick at:
    http://dmctalk.org/showthread.php?18125-***-SECTION-RULES-***-Please-READ-BEFORE-POSTING-***
  8. Replies
    10
    Views
    465

    Seems I remember him lurking around then. :devil:...

    Seems I remember him lurking around then. :devil:

    ...After the BS FB has been pulling lately, I would boycott them, if I wasn't permabanned already.:)
  9. Thread: Hood release

    by Ron
    Replies
    10
    Views
    315

    [General] 65606 That end of the cable may have broken...

    65606

    That end of the cable may have broken off...its part number 106804 (or #36 in the first link Rich posted above).
  10. Replies
    10
    Views
    465

    :cheers1:

    :cheers1:
  11. Replies
    12
    Views
    420

    [Engine] I'm guessing you had the mode switch set to AC...

    I'm guessing you had the mode switch set to AC...
  12. Replies
    8,558
    Views
    1,711,894

    [General] Finding cause of loss of rest pressure discussion...

    Finding cause of loss of rest pressure discussion moved HERE
  13. Replies
    18
    Views
    582

    65560

    65560
  14. Replies
    18
    Views
    582

    The post 1978 and adjustable have one that looks...

    The post 1978 and adjustable have one that looks like this (but the small o-ring you mentioned is missing):
    65555
    To get to the push up o-ring, push the keeper ring back (see arrow) to expose a...
  15. Replies
    18
    Views
    582

    Are you sure?? Pre 1978, there were no push...

    Are you sure?? Pre 1978, there were no push valves. Post 1978 used a push valve (as in the pic above) located on the right side of the FD when installed on a DeLorean. (You can look down the bore...
  16. Replies
    18
    Views
    582

    I think he meant the 3 o-rings shown here: 65553

    I think he meant the 3 o-rings shown here:
    65553
  17. Replies
    14
    Views
    519

    [Electrical] That ground may be causing some of the problems....

    That ground may be causing some of the problems. But the oil light and battery light have their own, separate, grounds. Since they use the same power source and the oil light works while the battery...
  18. Replies
    6
    Views
    1,115

    [For Sale] Missing post(s)? See the Sticky titled "***...

    Missing post(s)?

    See the Sticky titled "*** SECTION-RULES *** Please READ BEFORE POSTING ***"
  19. Replies
    6
    Views
    240

    [Frame & Body] The bell crank is not rotating fully to the...

    The bell crank is not rotating fully to the unlock position in your vid. A bent front latch rod (too short) or not making sure you have zero slack and zero tension on both rods when you install the...
  20. Thread: K-Jet parts

    by Ron
    Replies
    5
    Views
    449

    [For Sale] Please add prices. RE: ***-SECTION RULES ***...

    Please add prices.
    RE: ***-SECTION RULES *** Please READ BEFORE POSTING-***
  21. Replies
    9
    Views
    807

    [General] Barrel

    65301
  22. [Electrical] +1 ...and if it doesn't turn over, I would jumper...

    +1 ...and if it doesn't turn over, I would jumper cable the battery (-) directly to the engine and try again. And if that doesn't work, pull the starter.

    ("It's always the grounds";-)
  23. Replies
    8
    Views
    1,255

    [For Sale] The OP hasn't logged back in since 10-24-2020......

    The OP hasn't logged back in since 10-24-2020...


    EDIT: DPI did purchase the car and expects it to be restore by mid January.
  24. Replies
    17
    Views
    1,200

    [Engine] $.02 I don't see it being the battery. If...

    $.02

    I don't see it being the battery.
    If it's strong enough to start the engine, there would be enough power left to run the engine past the time it takes to get to operating temperature; Even...
  25. Thread: Heater not working

    by Ron
    Replies
    15
    Views
    1,495

    [Heat & A/C] The heater core's upper hose is the supply . ...

    The heater core's upper hose is the supply .

    FWIW, the heater core is relatively delicate -- Cut and peal the hose off rather than pull it.
    ..But I would check at the water valve instead, since...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4