Search:

Type: Posts; User: Ron

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds.

  1. Thread: Clutch replace

    by Ron
    Replies
    123
    Views
    3,933

    [Transmission 5-Speed] I wouldn't let that hold up the job for...

    I wouldn't let that hold up the job for days...maybe go to Ace/? and get a brass/bronze wire bore brush.
  2. [General] I could see it doing that if the CSV line was...

    I could see it doing that if the CSV line was swapped with the small WUR/CPR line (going to the Fuel Distributor).

    If the lines check out, does it run for 2-3 seconds after installing then...
  3. Thread: Warm start issue

    by Ron
    Replies
    19
    Views
    635

    [Fuel] Like David said, the injectors don't open at...

    Like David said, the injectors don't open at exactly the same time. Also, when they first open, they are not delivering at the same rate as when it's idling -- At idle, the rate is slightly higher,...
  4. Thread: Clutch replace

    by Ron
    Replies
    123
    Views
    3,933

    [Transmission 5-Speed] +1 Loctite or not, if it's torqued, a tap is...

    +1 Loctite or not, if it's torqued, a tap is going in there so I can see the threads -- I don't like $urprises!
  5. Thread: Red Tek

    by Ron
    Replies
    5
    Views
    121

    [Heat & A/C] The Red Tek docs say to charge at 0 pressure = no...

    The Red Tek docs say to charge at 0 pressure = no vacuum, which is what Stephen was saying. This is incorrect and Red Tek has it "slated to be removed from the documentation". Read it closely and you...
  6. Thread: Red Tek

    by Ron
    Replies
    5
    Views
    121

    [Heat & A/C] I've had several come through the shop with Red...

    I've had several come through the shop with Red Tec in them. It does very well, if installed in a flushed system. Two things I have against it: bad documentation and all of the pressures change,...
  7. Thread: Rear wheel bearing

    by Ron
    Replies
    2
    Views
    135

    [Suspension] Unconfirmed!!! National 513116 Timken 513116 ...

    Unconfirmed!!!
    National 513116
    Timken 513116


    EDIT:
    They Might be for the front?
    The above are:
    Inside Diameter (mm): 30mm
    Width (mm): 37mm
  8. [General] That would have been on .com (pre May 2011).

    That would have been on .com (pre May 2011).
  9. [General] Maybe ...

    Maybe http://dmctalk.org/showthread.php?12791-Digital-Dash-Project&p=211415&viewfull=1#post211415

    ..., post 196 and others in that thread
  10. Replies
    6
    Views
    622

    [For Sale] Check Shipping From 30572 HERE...

    Check Shipping From 30572 HERE

    106896 IDLE ECU [USED; 0609181820] DMCH NEW $343.75
    $150 OBO + Shipping USPS
    {Sale Pending}

    102778 Idle Speed Microswitch [USED; Checks OK] DMCH NEW 78.75...
  11. Replies
    8
    Views
    267

    [For Sale] :TrainWreck:

    :TrainWreck:
  12. Replies
    8
    Views
    267

    [For Sale] The only reason I asked is, if you were...

    The only reason I asked is, if you were successful with the trade you offered for your D, the site hosting that truck is located in some town in Russia.

    Domain Name: TOPCLASSICCARSFORSALE.COM...
  13. Replies
    8
    Views
    267

    [For Sale] Location?

    Location?
  14. Thread: Help on O Ring....

    by Ron
    Replies
    6
    Views
    198

    [General] Dipping them in the oil helps...

    Dipping them in the oil helps...
  15. Thread: Clutch replace

    by Ron
    Replies
    123
    Views
    3,933

    [Transmission 5-Speed] If you are not already installing :biggrin:... I...

    If you are not already installing :biggrin:... I wonder what the bearing travel would be for each after bolting them to the flywheel?
  16. Replies
    11
    Views
    695

    [Wanted] KillaCam, your other ad involving this item has...

    KillaCam, your other ad involving this item has been deleted, again. Not posting a location (again), placing the same item as For Sale and Wanted, and listing an item as "Brand new" when it has 1.9K...
  17. Thread: Clutch replace

    by Ron
    Replies
    123
    Views
    3,933

    [Transmission 5-Speed] Some people get to play with all of the good...

    Some people get to play with all of the good toys..
  18. Replies
    11
    Views
    695

    [Wanted] Location?

    Location?
  19. [Engine] It wouldn't have to be a huge leak....I say that...

    It wouldn't have to be a huge leak....I say that not because of semantics, but because a small leak will make it fail and that the adjustment it is so touchy that simply loosening and tightening the...
  20. [Engine] Did you get it out?? I usually pull them out...

    Did you get it out??

    I usually pull them out with a pen magnet. Sometimes I have to work it in and out a bit...
  21. [Engine] Dig deeper...the piston is still in there (with...

    Dig deeper...the piston is still in there (with o-ring).
    57732
  22. Thread: Clutch replace

    by Ron
    Replies
    123
    Views
    3,933

    [Transmission 5-Speed] After seeing this (and cataract surgery...

    After seeing this (and cataract surgery yesterday:-) I took another look at all of the pics. Not only does it appear that some of the weights were not moving as noted in post 54, pic 2, the parts are...
  23. Replies
    15
    Views
    574

    [Heat & A/C] Sounds like a diverter/duct problem to me too (if...

    Sounds like a diverter/duct problem to me too (if accumulator cold).

    ====

    fwiw, a partially restricted orifice would make the high side go high and the low side go low. Blocked, the high side...
  24. Replies
    12
    Views
    412

    [General] {Cue Mike}

    {Cue Mike}
  25. Replies
    13
    Views
    378

    [Electrical] Good luck! If it does, check the shutoff...

    Good luck!

    If it does, check the shutoff switch connections first. The cables don't have enough slack/flex to keep from loosening some of the bulkier ones up, imo. Clean and tighten often...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4