OK, thanks. I am not a fan of cutting wires also so I will use your method.
Type: Posts; User: lindbergh
OK, thanks. I am not a fan of cutting wires also so I will use your method.
Has anyone with a DMCH fuel pump PN#107000 performed the mod explained by SB-07-10/2017. The inertia switch when activated does not cut off the fuel pump. The fix calls for cutting the secondary...
To my knowledge DMC has never built a car from NOS or anything else without a VIN plate from the original vehicle. That will change now and new VIN's will be issued. A few weeks ago a never...
Check out - http://www.msn.com/en-us/tv/story/delorean-cars-are-coming-back/vp-BBoMerD and http://www.wral.com/delorean-goes-back-to-the-future-into-production/15280933/
Any takers for 100K. I...
[QUOTE=PJ Grady Inc.;185439]I guess you didn't read my post where I said 8mm and what type of wrench to use and how to approach it?[/Q
OK, thanks.
Found the bleed screw from the top. It is on top although not sure about getting tools in there, might be able to get a socket on there since it is pointing up. Can someone tell me what size the...
I am having trouble locating the bleed screw on the slave clutch cylinder. Cannot really see the slave cylinder and can barely touch it. Any tips? It's starting to look like I am going to have to...
I am having trouble locating the bleed screw on the slave clutch cylinder. Cannot really see the slave cylinder and can barely touch it. Any tips? It's starting to look like I am going to have to...
The U.S. is uncontrollably hemorrhaging cash. We took in more tax money last year in U.S. history and still have half a trillion deficit. Higher taxes on everything is our future. We feel your...
Right now there is not an interest from most collectors. Whether it ever will be is the question. As long as it is an enthusiasts car and not a collectors car the value will always be less due to...
Running without a T-stat is not a good idea. The T-stat restricts coolant flow (even when fully open) to keep the flow thru the engine at a constant rate. If you remove the T-stat you no longer...
For those of you with the original Ducy alternator: My tip is if you ever replace it with a one-wire alternator, do not cut the old Ducy plug off. Instead connect the one wire from the new...
The hub (with the high pressure switch and port) was replaced when the system was overhauled and don't really see a need to replace it again since it is not leaking and am not too worried about it...
About a year ago or so my fans failed (all fixed now) with the a/c on and the car idling. The high pressure port opened dumping the pressure (and the refrigerant with it). So my question is, is...
If you change the alternator you will most likely need the idiot light to work for it to charge the battery. The old ducy does not have this limitation but most modern alternators do. When I...
No chance of swapping, it was done one at a time. The brake does not feel spongy just have to put it on the floor to get decent braking. I will try a small adjustment of the rod. Thanks for the...
My brake pedal goes down about 2 inches before I get any braking at all and max braking (no lockup but hard braking) occurs at about the same time my pedal hits the floor. I have replaced the master...
Are there any non Delorean master brake cylinders that are compatible with our cars? Searching the site I saw a recommendation of a '79 Saab 900 and another '86 Saab. Are the proportioning valves...
I would look at changing it. There is probably no harm being done, yet, but I would not want to drive extended travel with it in the summer. I talked to an engineer at Redline a couple years ago...
Unfortunately, the DeLorean family probably has a case. DMCH bought the trademarks to DMC dealing with anything with the car. They should have negotiated to buy the DMC trademark lock stock and...
I replaced my brake master earlier this year and I was able to get the pins out but it was difficult as they were rusted in place. It took a lot of time over the course of a couple days. A...
I just wanted to make sure people know you do NOT have to disassemble the car as someone suggested to get in a locked trunk with a broken cable. That sounds silly to me.
You don't have to disassemble the car. Make this tool and leave it in the car. Practicing before it breaks might be a good idea though.
http://www.youtube.com/watch?v=RBqocO2zRpk
Trying to remove the old brakes hoses. Took the nuts that hold the hose to the bracket, but can't get the hose to back off of the bracket, the hose fitting is pretty rusted. Is there a technique to...
Does anyone know the size of resistor that needs to be placed in parallel with the alt. bulb for the purpose of keeping the alternator charging if the bulb goes out? I was thinking at starting at...