Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.29 seconds.

  1. [Wanted] I saw a few days ago someone on face book selling...

    I saw a few days ago someone on face book selling a set of them.
  2. Replies
    7,436
    Views
    1,067,418

    [General] What I'm thinking is because that boot is...

    What I'm thinking is because that boot is extended, it may always pull off. I guess there is no lip on the axle ends to prevent the boots from pulling off. What I may do is move the smaller end in...
  3. Replies
    7,436
    Views
    1,067,418

    [General] I just noticed that the boot that is slipping off...

    I just noticed that the boot that is slipping off is clamped at 4.1 inches from the bolt surface and the one not slipping is 3.3 inches from the bolt surface. The shaft has a rolled stop where the...
  4. Replies
    6
    Views
    179

    [Fuel] No start after a few seconds of shut down would...

    No start after a few seconds of shut down would not be caused by rest pressure loss. But the fact you got it started using the plug swap does indicate you are not getting fuel via the FD. I agree...
  5. Replies
    35
    Views
    926

    When charging the AC system, normally you connect...

    When charging the AC system, normally you connect a set of gauges to high an low pressure sides. Those gauges have a third hose that connects to the charging tank or vacuum compressor. The gauge...
  6. Replies
    35
    Views
    926

    Fittings for R12 and R22 are the same for high...

    Fittings for R12 and R22 are the same for high and low sides. It was the R134 that made different fittings. The reason was to reduce the amount of gas vented when the hoses were disconnected and...
  7. Replies
    35
    Views
    926

    The low side is the larger hose. But I think DPI...

    The low side is the larger hose. But I think DPI hose sets are the same size for low an high sides.
  8. Replies
    9
    Views
    182

    [Transmission 5-Speed] I got the top bracket off. There were two bolts...

    I got the top bracket off. There were two bolts 13mm socket on extension worked. I just found them by feel. One of the bolts was tight coming all the way out so I guess it was never removed...
  9. Replies
    9
    Views
    182

    [Transmission 5-Speed] Thanks. Is there a bolt on top? Can not see...

    Thanks. Is there a bolt on top? Can not see even with a mirror (old eyes can't focus that distance anymore).
  10. Replies
    9
    Views
    182

    [Transmission 5-Speed] Well I pulled the cross gate cable out of the...

    Well I pulled the cross gate cable out of the bracket. That required pulling one bold from the back to let the cable come back from the bracket. The top of the bracket still on the transmission is...
  11. I would try to open the throttle plates a little...

    I would try to open the throttle plates a little with curb idle screw to see if you can smooth out the idle.
  12. That vacuum seems way to high. Does your engine...

    That vacuum seems way to high. Does your engine have deceleration valves on the throttle plates? That high vacuum would make them open. I would guess your throttle plates are completely closed and...
  13. Replies
    9
    Views
    182

    [Transmission 5-Speed] Clutch replace

    Do I remove the cross gate cable from the bracket and leave the bracket in place or remove the bracket? Does the end of that cable have a pin that just pushes out?
  14. Replies
    7,436
    Views
    1,067,418

    [General] clutch replace

    Pulled the starter. I know I don't have the plate that holds the diagnostic sensor. Don't see another plate. I pretty sure Rob G did a clutch replace before I bought my car. The transmission...
  15. Replies
    7,436
    Views
    1,067,418

    [General] clutch replace

    Jacked the car up. Front on ramps, back on jack stands. Removed both axles. I think I've read the starter comes out and detach all the linkage next.

    Anyway the one new axle looks like one clamp...
  16. Replies
    36
    Views
    1,062

    [Fuel] The problem with loss of rest pressure quickly is...

    The problem with loss of rest pressure quickly is the injector hoses fill with bubbles. You can prime the fuel system but that will not do anything for the bubbles in the injector lines. The air...
  17. Replies
    35
    Views
    926

    +1 If it's a blend of gasses, you have to charge...

    +1
    If it's a blend of gasses, you have to charge via liquid with a large container but if using a whole can I guess your can charge via gas. The reason is each blend will not convert to gas at the...
  18. Replies
    35
    Views
    926

    If it's flammable, just use propane also sold as...

    If it's flammable, just use propane also sold as R12a.
  19. Replies
    7
    Views
    156

    [Fuel] Take the fuel take cap off. You may have...

    Take the fuel take cap off. You may have pressure in the tank.
  20. Replies
    4
    Views
    130

    [Electrical] With the diode in place, my ECU can't turn off...

    With the diode in place, my ECU can't turn off the advance. So that is probably what is causing the poor idle.

    Just pull the diode and connect the two wires (will plug into each other).
  21. Replies
    4
    Views
    130

    [Electrical] Did you do the diode bypass when you set your...

    Did you do the diode bypass when you set your idle switch to not connect?
  22. Replies
    3
    Views
    137

    [Suspension] Not normal. Did you just install the sway bar? ...

    Not normal. Did you just install the sway bar? Is it upside down?

    You can shorten the hose so the pipe moves forward.
  23. Replies
    22
    Views
    1,065

    Some GPS systems use an accelerometer to keep the...

    Some GPS systems use an accelerometer to keep the speed shown working when the GPS signal drops out.
  24. Replies
    7
    Views
    237

    [Heat & A/C] When powered by DC voltage, yes you can measure...

    When powered by DC voltage, yes you can measure resistance and calculate current.

    The #10 fuse also powers the blower speed 1 and 2. So one of your loads is drawing to much current or you have a...
  25. Replies
    8
    Views
    462

    [General] I have the EU radiator and Toby fans which I like...

    I have the EU radiator and Toby fans which I like very much. There are some new vendors products I have not seen in person yet.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4