FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: SBL

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. OK, will head out and go CW a bit. Just some...

    OK, will head out and go CW a bit. Just some degree of cycling will be fine, since I know that it should. No big deal if it cycles off a little higher than spec. Just don't want it to freeze up on an...
  2. Since it is always on, then, I would need to turn...

    Since it is always on, then, I would need to turn it CW then, right? I have RedTek in it which has the same properties, I believe, as R134a.

    Steve
  3. Well on most of my other ones, at about 3000 RPM...

    Well on most of my other ones, at about 3000 RPM cycling would occur. But not this time. There is a nice puddle of water under the car after I was testing all of this. But then again it is very hot...
  4. AC cycling switch which was to turn the adjustment

    After proper service I have great AC cooling but have noticed that there is no cycling.

    On the low side, when just starting up, the pressure is 45, which is fine. At 3000 RPM the pressure drops to...
  5. [Transmission Auto] I did not see much in the way of distortion with...

    I did not see much in the way of distortion with the holes, but maybe a little so I straightened them up.

    Whoever put the pan on before me apparently used a clear "make a gasket" approach, perhaps...
  6. [Transmission Auto] The DPI gasket was suck to the metal and had to...

    The DPI gasket was suck to the metal and had to be scraped off. Could not be reused.

    I see no support for the cork gasket of cork gasket plus sealant (with I did not use, as stated). I guess...
  7. [Transmission Auto] Sorry about the delay. Work got in the way. ...

    Sorry about the delay. Work got in the way.

    Well I changed the filter, and, it shifts perfectly. I think the lesson here is to do a quick visual check, of course, but filter filter filter. The...
  8. [Transmission Auto] I need to check to see if DMCFL did it when they...

    I need to check to see if DMCFL did it when they put in the computer. I have not had it very long so if they did it then it has been about a year. If not, then I don't know. On the list.
  9. [Transmission Auto] An odd slipping phenomenon of the automatic transmission

    My automatic transmission on my 1982 is slipping. It seems to be most prevalent from 1st to 2nd gear. Usually soon afterwards it goes into 3rd and stays, which is the limp mode. HERE IS THE...
  10. Replies
    9,192
    Views
    3,388,783

    [General] added this to steering wheel

    Just something to make it not look so bare. It looks better in person.

    65189
  11. Thread: Heater not working

    by SBL
    Replies
    16
    Views
    3,641

    [Heat & A/C] Well, I pulled the hose at the heater core. Water...

    Well, I pulled the hose at the heater core. Water was there, but it was not hot and did not flow. I hate getting in there with that valve. I have, in the past, caused added problems because it is...
  12. Thread: Heater not working

    by SBL
    Replies
    16
    Views
    3,641

    [Heat & A/C] Weekend is here! I found the following: At...

    Weekend is here!

    I found the following:

    At rest the plunger to the heater valve is out (which I presume is open).
    At running temp, heater on:
    The hose from the heater bottle is hot.
    The hose...
  13. Thread: Heater not working

    by SBL
    Replies
    16
    Views
    3,641

    [Heat & A/C] I bet that the heater itself is not getting any...

    I bet that the heater itself is not getting any hot water. I will check this weekend.
  14. Thread: Heater not working

    by SBL
    Replies
    16
    Views
    3,641

    [Heat & A/C] Heater not working

    Well it finally has become chilly in Florida, and I need to troubleshoot my heater, which provides no heat.

    I have never seen a drawing or description of the heater connections and controls,...
  15. [Electrical] Got it. It has a cracked connector area, and...

    Got it.

    It has a cracked connector area, and came back from DMCFL pugged in backwards, so it all makes sense.

    Steve
  16. [Electrical] bump; anyone measured it?

    bump; anyone measured it?
  17. [Electrical] Hate to bring up this old thread, but I cannot...

    Hate to bring up this old thread, but I cannot find the resistance readings for a property working TTS.

    For purposes if identification I will call the 2 pins "top" and "bottom"

    When cold, Top...
  18. Replies
    16
    Views
    6,022

    My flare is at the bottom of the console cover....

    My flare is at the bottom of the console cover. Well below the area where you would run a wire using the picture hanger technique.

    Still thinking. One could pull back the vinyl at that bottom...
  19. Replies
    16
    Views
    6,022

    front console cover flare

    Near the front of the car, at shin level, my console cover has flared on both sides. Just at the "wing" area. See picture. This happened when the previous owner took the car to a stereo shop and they...
  20. Replies
    3
    Views
    4,240

    [For Sale] yes, pictures would be nice.

    yes, pictures would be nice.
  21. Replies
    39
    Views
    12,177

    [Electrical] With the key out, I see +13 VDC at fuses 6,7,17,...

    With the key out, I see +13 VDC at fuses 6,7,17, and 18, and the speed 3,4 breaker. Looking at the schematics this seems to be correct. I then removed each fuse to look for current across the fuse...
  22. Replies
    39
    Views
    12,177

    [Electrical] Could there be something amiss in the new DMCH...

    Could there be something amiss in the new DMCH alternators? I had never drawn down my battery before, but then I changed my alternator to the new DMCH one because I could sense that the bearings were...
  23. Replies
    9,192
    Views
    3,388,783

    [General] Since she lives here anyway, thought I should...

    Since she lives here anyway, thought I should take her to the other side of the house for a few pictures on the beach.

    6401764018
  24. Replies
    36
    Views
    36,719

    Here is a trick I learned from Ken K. In fact we...

    Here is a trick I learned from Ken K. In fact we did this on my door headliners on his kitchen table in Cincinnati. When finished, put garbage bag or plastic material over the panel, and then add...
  25. Replies
    9,192
    Views
    3,388,783

    [General] Battery cut-off switch

    I installed this battery switch. I favor hefty purely mechanical switches. No chance for even small current drains, no latching relays, no need to reach far back into the battery compartment to the...
Results 1 to 25 of 138
Page 1 of 6 1 2 3 4