Hi everyone.
Had the DeLorean setting in the driveway a couple of days and my binnacle split right down the middle, the material covering it i mean. I called DMC midwest and talked to them but the...
Type: Posts; User: penciltester
Hi everyone.
Had the DeLorean setting in the driveway a couple of days and my binnacle split right down the middle, the material covering it i mean. I called DMC midwest and talked to them but the...
So what temp would you guys say the "Danger Zone" is?
"Danger Zone" reference with a nod to dmcvegas and moneypenny.
Thanks for the reply. So the first tick mark above 100, is that about 155/160?
So from what I have read if I turn on my air conditioning with the key turned on but not with the engine running, my fans should kick on, correct? They do but only for a few seconds. Like maybe to a...
Thanks guys. Either I never noticed before and was just hyper aware after changing to leds and new alternator or ,if it has anything to do with the alternator, the old one was worse off than I...
We installed a new alternator from DMC Midwest, seems fine and dandy but my battery light flickers when the key is turned to accessory position. Any ideas? Thanks again guys.
Because of health issues Byrne is hanging up his hat. I spoke with him today. He said they still have inventory and seemed open to orders but said he would have someone else taking care of the...
We removed the trim around the windshield to paint it. One of the wires attached to the trim was detached from whatever it was originally grounding. Drivers side bottom wire. What does this go to?...
Thanks for clearing that up. What about the trim pieces running the length of the car?
So I was wondering what the louvre over the engine compartment was made of? Fiberglass? The side vents the same?
Thanks
I have SEM black trim paint. Not sure what kind of gloss it is.
Hmmm, ok so is it recommended to just use back to black regularly on the bumpers and mirrors? Has anyone painted them, if so how'd it turn out?
DMCMW Dave and/or soundkillr, are you recommending...
So this Sunday, hopefully, we will be painting the black bits. My dad has a little shop with the correct tools and we have the correct paint. What prep do you guys recommend? Just soapy water and...
@Josh
What is the installation procedure compared to Heninger and Associates bracket?
This might have been beat to death already but what are your guys opinions on these door brackets? Do they actually help reduce roof separation? Just a gimmick? Those who have them, do you think it...
Last night really but......Checked the TABS, cleaned up the battery ground connection and replaced leaking trans axle seals*shudder*. That was a pain.
Thanks again everyone for the replies and the help. Also, sorry for the late reply. My life kinda went sideways for a bit. I'm thinking about getting the torsion spring,...
Thanks everybody for chiming in. The bar broke off center near the rear hinge. Some have mentioned roof box separation being a probable cause for added stress on the bar. Has anyone reattached their...
Yes, they are the same. I read something about their strut/torsion door system being called blue sky. I may be mistaken, sorry for the confusion. Thanks for clearing that up.
Thanks for the info guys. Well if no one on here has a torsion spring spring from Blue Sky I might as well be the guinea pig.
Sweet Jesus! Nothing like having your driver side torsion bar snap while driving down the road to scare the ever loving crap out of you.
So now I get to replace the torsion bar. I have seen the...
I purchased new headliners from DMC Midwest. I am at the point where I need to stretch the fabric up and over the lip that the door seals are pushed on to. What adhesive do you guys recommend for...
May or may not help but check your grounds in the engine bay. Attached to the intake manifold right hand upper corner, towards the firewall, this will jack with your FV amongst a good amount of...
So both cables are attached. Passenger side locks up like a champ. Drivers side not so much...or at all. We followed the instructions for adjusting the brake. Remove pin, turn screw. The thing does...
Heh, well right before we were about to pull the intake manifold I detached the grounds in the engine bay again. Cleaned again, but I moved the ground for the oxy sensor etc.. To a different spot on...