Has anyone recently installed the Stainless Steering Shaft and U-Joint sold by DMC Houston?
https://store.delorean.com/100840ss-stainless-steering-u-joint.html
I have it to install, and was...
Type: Posts; User: uhhair
Has anyone recently installed the Stainless Steering Shaft and U-Joint sold by DMC Houston?
https://store.delorean.com/100840ss-stainless-steering-u-joint.html
I have it to install, and was...
Any examples of ones you could link to that would work?
Tried searching the forum but it looks like the latest comprehensive thread on spring removal was started by my buddy Justin and is over a decade old, and most of the links to products in it are...
I figured it out, although by accident sort of. Apparently if you have a loose connection any of the 3 Red/Orange wire points (The headlight switch, the hazard switch, or the AC panel relay), if it...
Yeah I tried that after the new Rheostat didn't fix the issue, and just connecting all the wires together does not make the lights come on either.
Okay so I'm having an issue with my White Binnacle Dash lights (the ones that should illuminate the entire dash) not coming on. Here is what I have done/investigated so far:
1. Replaced the...
Looking for a lower engine cover to replace mine, as mine is cracked and no longer serviceable. I'm located in PA, willing to travel to pick it up rather than ship it and risk breaking. Thanks!
Thank you both for the help. Looks like my plastic nut is in two pieces and broken, which is why I was confused as to the assembly. Now to figure out what it's called and how to source a...
So it appears the reason I couldn't figure out how to assemble my engine latch cable was my plastic piece is broken into two, when it should be one.
I obviously don't need to replace the entire...
Does anyone have a picture of the engine cover cable attached to the backplate of the car fully assembled? I'm putting the rear plate/fascia on the back of my car and I forget what the hooked up...
Well I figured it out! Turns out that there was a tiny screw on the control for hot/cold that came loose. I'm not sure what the part name was, but it was at the far end of the cable right by the...
Thanks everyone for your insight. From what I am feeling, the air is blowing hot, not just ambient warm air. At first I thought this was an AC issue so I did hook up all of my gauges and the...
So it looks like my AC is working, but when it is on my vents still blow out hot air. I am guessing it is related to whatever mechanisms happen behind the vents to direct air from the heater core to...
Got it! With regards to a possible bad air mix valve, do you know what part number this is or how I could specifically test/rule this out?
OK so the plot thickens... now my AC is not working at all. The compressor is still always on, and I did hook up some gauges to see what they might mean. The first gauge is the car at idle,...
Thanks for the insight everyone! I went ahead and ordered some gauges and will hook them up and check everything out! I do think this was just a case of it being too hot outside, as I drove the car...
Last year I gave my AC system a complete refresh consisting of a new compressor, accumulator, lines, and orifice tube. It is also now filled with R134A. I had no issues with the system last year, but...
So I am actually doing a similar install right now. I can tell you my biggest challenge has been finding a single DIN unit that still has a flip-out screen. All of the units that used to have this...
Good discussion guys, thanks for the ideas.
The fuel lines and rubber hoses are all brand new, I replaced them 6 months ago when doing the water pump on the current engine in the car, which is at...
Okay, so as the post states, I'm going to be pulling an engine out of my D, and transplanting another stock Delorean engine in it's place.
The engine I'm putting back into the car is in good shape...
Thanks for the help! I was able to get it in after removing the top muffler bracket. I couldn't see without it and trying to do it by feel was just not working and I wasn't strong enough to do it...
Here is what I was shown from the website. The silver piece on the bolt is what appears to be the spacer. Without it, the alternator will have play from front to back so I'm sure that it is needed...
So I recently got a new Delorean Go alternator and it appears that there is a spacer that needs installed with it. It appears that it goes on the front side inside the bracket and the front of the...
I'd be interested in this as well if anyone has her contact info!
What solvent should i be using? I dunno, I am just overwhelmed at this point and think I'm going to take it somewhere to be done. I clearly have no idea what I am doing and it seems like everyone...