here are some photos of Model S, RHD ibooster (gen1) with Model Y reservoir tank. it clears the cover, but the hole is in the wrong place, so need to get a piece of plexiglass and cut it to shape and...
Type: Posts; User: Reinsch
here are some photos of Model S, RHD ibooster (gen1) with Model Y reservoir tank. it clears the cover, but the hole is in the wrong place, so need to get a piece of plexiglass and cut it to shape and...
in my particular case, I was dealing with all brand new and dry brake lines, also all rebuild calipers, so theoretically it should be harder to remove any air bubbles.
The first step was to "bench...
Tank from iBooster gen 2 will fit to iBooster gen1.
If model 3/Y tank is currently the best known solution imo.
I fitted gen2 tank from a Nissan, but only due to the level sensor that was missing...
I've decided to develop the bracket with a correct angle which is important to avoid premature wear of piston on ibooster bore. I've spoken with my colleague who is a brake engineer and told me that...
possible issues :
- The iBooster stroke might be different then the stroke of the Delorean master cylinder - you better off with matched units otherwise you risk damaging the master cylinder...
As previously noted, iBooster gen1 accepts M12 fittings and standard Delorean brake cylinder fittings are M10.
Below iBooster Gen1 form Tesla Model S RHD (ports on "Delorean side")
...
Gen2 ibooster is unlikely to fit, but you are welcome to prove me wrong (please read my previous posts).
Tesla Model S Right Hand Drive ibooster gen1 has brake ports on master cylinder on...
You can scrap both (bracket and adapter) and make one from scratch that is stiffer and offsets ibooster accordingly.
From what I've read, stock bracket and dash panel itself can flex under heavy...
Thanks for remarks and photos.
Do you recall clearance between stock Delorean booster and tank/frame before swap ?
In your opinion, knowing that iBooster gen2 (Tesla model 3/Y) is hanging lower...
indeed. Date indicates it was in mail 7 days ago.
how's that ibooster or yours? Does it fit ?
there is always some adjustment.
If not enough, you can cut the shaft, thread one end with left thread, the other with right and use roman screw.
or thread them same and use long nut, but for...
thanks for that!
RHD model S has that in flipped config already. Plus brake pipe connection is on other side :
https://i.ebayimg.com/images/g/os0AAOSw4JFfhyyf/s-l1600.jpg
https://lh3.googleusercontent.com/pw/ACtC-3dXtjBIwKE-Cuc4Bi4nGSTctt4hYj0kfUNeMVp4ZboeMIs716NlOuSzXiDvOwpdzIHa4AVaHmiRbpNfsibJE8uwGSJAn4AItgq59ZoV4aX9C17dwkQ9mmt-FSVy1kKf9oEYWSLy_nNgwfDH73ceM7yOnQ=w147...
For those who consider iBooster Gen2.
Please note there is difference between ibooster from LHD vehicle and RHD vehicle.
LHD booster:...
I've invested over 400 GBP to 3d scan rear section of frame, transmission and part of engine room. I also have my new engine. Did all that before doing engine swap to make sure all will fit nicely....
For reservoir I'm not that concerned as long as there is no clash (looking in CAD it will be fine for gen2). I can always cut new access hole/make new cover if not exactly in correct place.
My...
anybody tried iBooster gen2 from model 3/Y ?
I'm planning to fit that unit. Clearance to body is fine (checked in 3D CAD), but not so sure about frame/fuel tank as I don't have that area 3D...
@81dmc
thanks for your quick reply!
do you get full pedal travel ? or you think there is a bit left? Can you lock wheels at higher speeds if you press it hard enough ?
thanks,
Marek
@81dmc
any chance you have more photos showing mods you did to fit ibooster to DeLorean? New or modified bracket? connection to pedal?
I'm doing engine swap (#vin4454 on Facebook) and as my...
@jangell
You are right, Arduino power output is limited. Manual says : max per pin 20mA, recommended 10mA. Power sum for each group should not exceed 100mA. Max for entire package 200mA. This is...
Hello members,
I thought I will share my project in regards of automation of heater box. As my project car #4454 is undergoing resto-modification, all parts are reviewed and upgraded if possible....
If you add the relay you should be good from electrical point of view!
kind regards,
Marek
Hello and welcome all!
I'm Marek, electrical engineer working in automotive industry in UK. DeLorean enthusiast for over 15 years. This affection actually decided about my career (it was a...
Hello owners!
I thought I will write little article about Air Con (A/C) system on D as it is not the best design from electrical point of view. I will focus on electrical part as I'm Electrical...