Seems to be a very similar set-up to this that's been around for a good few years: https://dmctalk.org/showthread.php?17041-How-To-Install-Borgeson-vibration-dampening-u-joints except for it's a...
Type: Posts; User: chris williams
Seems to be a very similar set-up to this that's been around for a good few years: https://dmctalk.org/showthread.php?17041-How-To-Install-Borgeson-vibration-dampening-u-joints except for it's a...
Should have posted this but yes all sold. Thank you for the interest.
I have been sitting on some NOS drivers side torsion bars for a long time and have decided to sell a couple to help fund moving home they are listed on UK eBay but happy to do a deal off eBay....
I'm close to Cambridge myself so 'probably' not on your route either, however feel free to get in touch if you need anything. I don't think you can access the test track and from the last pictures...
Plenty of UK owners available via the UK Owners Club, What route are you taking through the UK? Have you contacted anyone in N.Ireland regarding visiting the site? I'ts not really that accessible. I...
There is a way to do this without any phone (still not sure why that works anyway) but involves powering up a wire at the engine. I have done this myself but your operating the window switch. If...
I have converted many of these for DeLorean usage in the UK, that's assuming it's the early odd fire engine. The later even fire ones are plentiful, Perhaps you could get in touch via the UK owners...
As wrote above, a common modification if you trace the wires they 'probably' go to (or did) an over-ride switch.
Chris
Not particularly, slow and steady. Make sure you get the control arm supports in the correct orientation! You may find a jack helpful under the LCArms to re-connect the hub to the upper control arm....
Mine leaked from the same place for years and assumed it was the rear crank seal...... Then I bothered to smell the oil and realized it was G/box oil! So yes I would do as suggested and check the...
I have fitted them both to my own car and another. They are very well made and a perfect fit, I also fitted Ed's S/Steel lower arm support kit to mine as well. I cant report back on handling as yet...
As wrote above! what you have are the OE ones, most people replace with a one piece metal plate with welded on studs, however I guess you don't have the deflector shields either!
That's quiet nice, reminds me of an Aston Martin from the rear.
Chris
I have seen a few like this, if your careful you can get a nut (masking tape stuck into a ring spanner) inside the frame and use the correct bolt through the frame. Not a perfect solution but seems...
Thanks Josh
Very nice, can you post a link please as I could not find it on the website.
Chris
Short answer: does it look the same? if so yes. The later even fire will not. But it's an easy swap over (done many) if it's the correct one, just the bottom end and a few other bits & bobs.
Chris
There are a few import companies that UK owners use for importing vehicles such as Trans Global Logistics being one who also specialize in bringing in vehicles for military personnel such as those at...
Nice thread on the subject here: http://dmctalk.org/showthread.php?16914-Need-help-with-source-of-major-oil-leak
I had the same issue trying to fit the DPI new fan set, one of the first IIRC! This was not an issue with the shroud simply the 35 year old rad giving up. I purchased a new rad from Ed at DMC EU and...
Very unusual yes, But if memory is correct it can be replaced by just dropping the sump. However if it's holding the correct pressure then I would doubt it's failing. Is the oil pressure gauge...
Very good but the V8 PRV already exists.
Chris
Difficult to tell from the picture but as others have suggested it could be a case of block rot. I recently did an article in the club magazine about this having had an engine 'chopped' in half to...
http://deloreans.co.uk/forum/showthread.php?tid=5862
Car has been sold prior to auction however.
Chris
I have always wondered if a modern style of fuel cooler, as is fitted to most diesel common rail engines nowadays would be beneficial to cars that suffer from hot fuel return (not usually to much of...