Search:

Type: Posts; User: DMC5180

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    139
    Views
    39,685

    Apparently someone else has ambitions of taking...

    Apparently someone else has ambitions of taking on a EV conversion using a model 3 Drivetrain.

    https://youtu.be/omXq-6LbV6M
  2. Replies
    7,818
    Views
    1,195,137

    [General] I think thatís the straightest rear facia Iíve...

    I think thatís the straightest rear facia Iíve ever seen. They almost always have a smile.


    Sent from my iPhone using Tapatalk
  3. Replies
    24
    Views
    2,859

    [Frame & Body] The lower panel you are thinking of did not cover...

    The lower panel you are thinking of did not cover the entire bottom of the engine. Brandon Moody, a former owner from Kentucky, created an Aluminum panel to mimic the intent of the original concept...
  4. Replies
    13
    Views
    1,420

    [Suspension] alignment specifications

    Unless you just want to look at it, the alignment specs are in virtually all alignment equipment manufacturers data bases. The only nuances I can think of, is the measurement of frame height to the...
  5. Replies
    26
    Views
    1,503

    Sticky: [General] FRAMING JOHN DELOREAN - Official Web-Site

    Wow! Awsome trailer Tamir. Really looking forward to seeing it. Did you have access to Proto 1 for the reveal re-enactment?


    Sent from my iPhone using Tapatalk
  6. Replies
    26
    Views
    1,393

    Theres not enough left of the engine compartment...

    Theres not enough left of the engine compartment to determine a cause since everything plastic was consumed by the fire. You can only speculate as to the most probable cause.

    Sadly this is a...
  7. Replies
    3
    Views
    217

    [General] I think the forum you are looking for is...

    I think the forum you are looking for is DMCtoday.com

    Walter Coe pretty much dropped out of all things Delorean about 2010. Thats the last time I recall seeing him at a DCS event. Although it...
  8. Thread: Water leak

    by DMC5180
    Replies
    13
    Views
    908

    [Frame & Body] Check the screws that hold down the finisher...

    Check the screws that hold down the finisher grill at the base of the windshield and the windshield wiper arm pivots for play. Also check the washer fluid hose fitting where it goes through the...
  9. Replies
    8
    Views
    337

    [Transmission 5-Speed] Kinda curious why you ask. The CV joints on the D...

    Kinda curious why you ask. The CV joints on the D rarely if ever need replacement. New boots and fresh grease is usually all thats ever needed.


    Sent from my iPhone using Tapatalk
  10. Replies
    156
    Views
    37,759

    Iím surprised the VIN and Key code a not written...

    Iím surprised the VIN and Key code a not written on that door. Perhaps the other door has it.


    Sent from my iPhone using Tapatalk
  11. Replies
    24
    Views
    2,859

    [Frame & Body] Air deflection plates (DIY anyone?)

    I wouldnít use those. The 3 stud strip type units are much better and easier to install. Virtually every vendor sells them.
    ...
  12. Replies
    9
    Views
    335

    [Fuel] In that case probably hot fuel collapsing the...

    In that case probably hot fuel collapsing the soft pickup hose. I have a spring in mine to prevent that. But on rare occasion When driving in hot temps with low fuel in the tank, I would occasionally...
  13. Replies
    9
    Views
    335

    [Fuel] Sounds like you a broken pickup hose at the...

    Sounds like you a broken pickup hose at the bottom of the pump. The pump sucks air, you lose fuel pressure, engine dies, fuel in tank sloshes forward, gets picked by the pump, engine fires up,...
  14. Replies
    20
    Views
    3,480

    [Engine] Not likely, thatís a fatigue fracture from heat...

    Not likely, thatís a fatigue fracture from heat cycling. The cylinder head exhaust studs are famous for thermal fracturing especially on the cylinder ports closest to the crossover pipe. Both of my...
  15. Replies
    20
    Views
    3,480

    [Engine] I have too say, thatís the first time Iíve seen...

    I have too say, thatís the first time Iíve seen that bellow joint fail. I always wondered how long they would hold up. Iím sure the shops that work Deloreans full time, see it on rare occasion but...
  16. Replies
    7,818
    Views
    1,195,137

    [General] Please get the Paint code from them. Thatís...

    Please get the Paint code from them. Thatís probably the most spot on match Iíve seen yet.


    Sent from my iPhone using Tapatalk
  17. Replies
    25
    Views
    650

    [Fuel] It is a compression sleeve. It cinches itself...

    It is a compression sleeve. It cinches itself into the tapered seat of the fitting. A drop of oil on the threads will help the tightening process. Unfortunately, I donít know what the correct B-nut...
  18. Replies
    25
    Views
    650

    [Fuel] Fuel pump return and feed line

    As long as the hose says SAE 30R14 T2 you should be good.



    Sent from my iPhone using Tapatalk
  19. Replies
    25
    Views
    650

    [Fuel] You may want to replace those hoses anyway as a...

    You may want to replace those hoses anyway as a preventative measure even if they arenít the source of the leak.

    This is what happened to mine this past September about a a mile from my house. My...
  20. Replies
    25
    Views
    650

    [Fuel] A couple photos of the old hose would help....

    A couple photos of the old hose would help. Theses cars are old enough now that many have had the hoses replaced at least once already, especially if it had multiple previous owners. The Original...
  21. Replies
    25
    Views
    650

    [Fuel] How is the pump cover holding up for you? ...

    How is the pump cover holding up for you?


    Sent from my iPhone using Tapatalk
  22. Replies
    25
    Views
    650

    [Fuel] Yes Sent from my iPhone using Tapatalk

    Yes


    Sent from my iPhone using Tapatalk
  23. Replies
    25
    Views
    650

    [Fuel] They are the screwdriver type, just the ask them...

    They are the screwdriver type, just the ask them for the correct line clamps. I ended up with a small assortment pack and used the ones that best fit the hose OD.




    Sent from my iPhone using...
  24. Replies
    25
    Views
    650

    [Fuel] Yes, but it must be Gates Barricade Fuel...

    Yes, but it must be Gates Barricade Fuel injection hose. Napa sells it by the foot. What I donít recall is the size I used. 1/4-6mm or 5/16-8mm. They also have the correct type of clamps for the...
  25. Replies
    711
    Views
    81,084

    Great work on the HP/LP harness wiring....

    Great work on the HP/LP harness wiring. [emoji122][emoji122][emoji122][emoji122][emoji482]


    Sent from my iPhone using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4