FRAMING JOHN DELOREAN - AT THEATERS THIS WEEKEND & ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    42
    Views
    2,072

    [Electrical] I was busy with more inventory building so have...

    I was busy with more inventory building so have not done much on the LED headlights. I don't think the 4 sided LED headlights are going to work as my low beams. They don't really produce a flat...
  2. Replies
    8
    Views
    197

    [Engine] I'm pretty sure the water pump is always pumping...

    I'm pretty sure the water pump is always pumping coolant through the engine and heater core even before the thermostat opens. So I can't see the improvement you would get by moving to a water pump to...
  3. Replies
    36
    Views
    1,095

    [General] Do you see the tach moving when your cranking the...

    Do you see the tach moving when your cranking the engine?
  4. Replies
    36
    Views
    1,095

    [General] Check your pipe of agony. Remove the air...

    Check your pipe of agony. Remove the air cleaner, shine a light on the drivers side where the pipe enters the mixture unit, press the air flap down and see if any light is showing around the end of...
  5. Replies
    7,866
    Views
    1,213,146

    [General] Thanks for that tip. I do have an extra set of...

    Thanks for that tip. I do have an extra set of plugs but may wait till the rotor and cap get replaced. I've never replaced the rotor and cap so it may be original.
  6. Replies
    36
    Views
    1,095

    [General] +1 When your injector lines are dry you need the...

    +1
    When your injector lines are dry you need the cold start injector to get the engine started.
  7. Replies
    36
    Views
    1,095

    [General] Make sure you did not forget to connect the...

    Make sure you did not forget to connect the vacuum hoses and the pipe of agony is seated.
  8. [General] It won't be corrected by adjusting the primary...

    It won't be corrected by adjusting the primary pressure unless that is to high.
  9. [General] OK. Your control pressure is to high. Most...

    OK. Your control pressure is to high. Most likely you need a rebuilt warm up regulator but if the filter on the WUR (inlet screen is plugged or dirty) that can cause the pressure to be to high.
  10. [General] So you want to set 5.2 bar (75.4 PSI) if your...

    So you want to set 5.2 bar (75.4 PSI) if your adjusting it to design. I set mine but I did not notice any change in engine operation from where it was at 70 PSI.
  11. [General] 65 PSI is not to high for primary pressure. It...

    65 PSI is not to high for primary pressure. It should be 75 PSI but most cars are running around 70 PSI that I've tested.
  12. [General] What pressure are they reading? I wonder if they...

    What pressure are they reading? I wonder if they hooked up the gauge correctly. It is pretty easy to pull the return hose from the pump and see if any fuel is returning.
  13. Replies
    7,866
    Views
    1,213,146

    [General] Replaced the coil and that did not fix it. So...

    Replaced the coil and that did not fix it. So going to order a new cap and rotor.
  14. Replies
    10
    Views
    411

    If money is no object, these servos should have...

    If money is no object, these servos should have plenty of power and they hold without power.
    ...
  15. Replies
    7,866
    Views
    1,213,146

    [General] Agree. Since reducing the high voltage by...

    Agree. Since reducing the high voltage by reducing the gap helped I'm thinking it may be a cross fire. I'm not running a stock coil. I'm running a GM ignition module and a 1.5 ohm coil. I will try...
  16. Replies
    7,866
    Views
    1,213,146

    [General] Well today I checked the fuel pump current at 6.3...

    Well today I checked the fuel pump current at 6.3 amps. engine off so that looks fine. Since I was in the washer bottle area I though maybe a connector for the fuel pump wire got moved.

    I then...
  17. Replies
    7,866
    Views
    1,213,146

    [General] Took the D to the grocery store just now. The...

    Took the D to the grocery store just now. The engine is skipping mostly when the engine is loaded during acceleration. It did it cold and hot so I suspect it's a problem in ignition. I checked the...
  18. Replies
    42
    Views
    2,072

    [Electrical] So are these black plastic strips that go between...

    So are these black plastic strips that go between the lights just to remove the chrome look of the headlight benzyl? I was thinking of painting my benzyls black.
  19. Replies
    42
    Views
    2,072

    [Electrical] Here are some photos of the 4 sided new LEDs on...

    Here are some photos of the 4 sided new LEDs on the driver's side inner light (High beam) and the old 2 sided LED on the passenger side inner light(High beam). As you can see a big difference in the...
  20. Replies
    11
    Views
    366

    [Heat & A/C] I once had a compressor bolt fall out (not on a...

    I once had a compressor bolt fall out (not on a DeLorean). The result was a leak like your seeing. The threads were stripped but it had held many years with no problems. I guess the factory had...
  21. Replies
    9
    Views
    424

    [General] Got the harness wrapped and installed. Can't get...

    Got the harness wrapped and installed. Can't get the grommet where the harness passes through the washer bottle installed. Also left the washer bottle out and will put that and the grommet in when...
  22. Replies
    9
    Views
    424

    [General] Wish I never started the wire replacement. Way...

    Wish I never started the wire replacement. Way to much work for what it improves. With LED headlights there is less voltage drop over the wiring anyway because there is less current draw. But the...
  23. Replies
    10
    Views
    401

    [Fuel] Use a solvent to clean the valve in the idle...

    Use a solvent to clean the valve in the idle motor. Shake or blow out the solvent, let it dry and use a little light oil on the valve. Don't turn the valve with anything metal, use wood so you...
  24. Replies
    10
    Views
    401

    [Fuel] The most common causes of idle hunting are a weak...

    The most common causes of idle hunting are a weak O2 sensor and or a dirty idle motor. But some cars seem to hunt a little no matter what you do. Also the adjustment of the curb idle screw will...
  25. Replies
    1
    Views
    144

    Sorry, forgot the link. ...

    Sorry, forgot the link.

    https://www.sherco-auto.com/striped-tracer-wire.html?Array=&utm_source=&utm_medium=&utm_term=&utm_content=&utm_campaign=
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4