Search:

Type: Posts; User: dn010

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    7
    Views
    771

    The trim has a strip of foam adhesive that runs...

    The trim has a strip of foam adhesive that runs down one side of it. You can see it as the gray with red film in the photo of the cross section. This was enough to secure it in place.
  2. [General] Try Rob Grady. He seems to have some odds and...

    Try Rob Grady. He seems to have some odds and ends when you least expect it.
  3. Replies
    23
    Views
    3,698

    You're about 3 years late. :dunno:

    You're about 3 years late. :dunno:
  4. Replies
    23
    Views
    3,698

    I don't know why I'm surprised anymore, that...

    I don't know why I'm surprised anymore, that people shoot down something that someone else went through lengths to find and help the community with.


    But anyway, on a + note; I may not longer be...
  5. Replies
    1
    Views
    122

    [For Sale] Sorry, to conform with the rules- Location:...

    Sorry, to conform with the rules-

    Location: The ARB is located right next to my DeLorean in my garage in hot and sunny Seminole, FL, 33777. Because of this fact, I'm tired of tripping over it...
  6. Replies
    1
    Views
    122

    [For Sale] ARB Anti Roll Bar 100233

    Part: ARB or Anti-Roll Bar (Front) #100233 (DMCH$208)

    Story: This ARB was installed on frame #308 from VIN 712 that was located in CA. I purchased this frame to use for a swap. Originally I...
  7. Replies
    8
    Views
    248

    [Fuel] The fuel distributor itself has the score, not...

    The fuel distributor itself has the score, not the line:
  8. Replies
    8
    Views
    248

    [Fuel] Tiny notch on Fuel Distributor

    Might be easier/safer to file it down flat.
  9. Replies
    20
    Views
    610

    [Frame & Body] There are three screws on each side you mentioned...

    There are three screws on each side you mentioned but there are also three screws holding down the plastic strip above the rear glass you have to remove. Once that is unscrewed you pull the bottom of...
  10. Replies
    27
    Views
    887

    [Fuel] Don't forget the cost of the tooling to crimp the...

    Don't forget the cost of the tooling to crimp the fittings on unless you're going to buy barbed banjo fittings. I don't know - maybe it's just me, but I'm sure there is a good reason no one has ever...
  11. Replies
    15
    Views
    591

    [Frame & Body] Thanks much. And they even have it by the quart...

    Thanks much. And they even have it by the quart so I can shoot it on! :yesss:

    I'll order it and hopefully everything gets here by the weekend so I can begin this repair.
  12. Replies
    27
    Views
    887

    [Fuel] +1! Well stated.

    +1! Well stated.
  13. [Electrical] http://support.delorean.com/kb/a57/a-c-panel-illum...

    http://support.delorean.com/kb/a57/a-c-panel-illumination.aspx

    https://www.dmcnews.com/Techsection/acpanellites.htm
  14. Replies
    27
    Views
    887

    [Fuel] I do a lot of my own stuff but this is one area I...

    I do a lot of my own stuff but this is one area I wouldn't mess around with DIY. I know they're expensive but I'd spend the money on lines from a vendor, that have been designed, built and tested for...
  15. Replies
    15
    Views
    591

    [Frame & Body] Michael, guys - awesome and thank you for your...

    Michael, guys - awesome and thank you for your advice! I'm waiting for the 3m semi-rigid to come in and then I'll give the repair a shot. Next question is - what are people using to paint the black...
  16. Replies
    15
    Views
    591

    [Frame & Body] Advice on fixing fascia

    So this happened about 15 years ago. I want to refinish my rear fascia and take care of this so itís not a damn eyesore. The rear fascia is one of the main reasons I donít take the car to shows. I...
  17. Replies
    13
    Views
    1,000

    The 2nd annual car show was November 2018. IF...

    The 2nd annual car show was November 2018. IF they even do a 3rd annual, I'd imagine it being around that time frame but there is no news about it and this is the Radio Station that is posting that...
  18. Replies
    12
    Views
    1,041

    One step forward...

    One step forward...
  19. K-jet pressure gauges, PPR shims, WURs, CSVs

    And after the flood of issues seen currently in general discussion, I'm happy as hell those days of dealing with BS are over. Really I just wanted to say that I am going on 4 years of issue free...
  20. Replies
    20
    Views
    610

    [Frame & Body] Well, here was mine and I avoided any FG damage....

    Well, here was mine and I avoided any FG damage. :)

    59954
  21. Replies
    20
    Views
    610

    [Frame & Body] Along with the bolts I also used the hardcore...

    Along with the bolts I also used the hardcore rivet that came with the brackets. Need a larger rivet gun for them. I opted to do both sides even though only one was bad. I too doubt Iíll need to...
  22. Replies
    20
    Views
    610

    [Frame & Body] I did not use any of the plates for the back. I...

    I did not use any of the plates for the back. I felt the bracket is well made compared to original and wouldnít bend. I think the back plates are useful if you have fiberglass damage.
  23. Replies
    20
    Views
    610

    [Frame & Body] I used the kit from Grady years ago, it involved...

    I used the kit from Grady years ago, it involved removing the upper infill panel if my memory is fine. Unless the original bracket was warped so much that you now have damaged fiberglass, you donít...
  24. Replies
    14
    Views
    566

    I'm all for new and improved, but I too am very...

    I'm all for new and improved, but I too am very satisfied with my LED bulbs on my Grady boards. They're very bright and a big improvement over the incandescent original bulbs.
  25. Replies
    38
    Views
    1,278

    [Engine] Dumb question, but are you plugging the CO...

    Dumb question, but are you plugging the CO adjustment screw hole after you make the adjustments and go for a drive?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4