FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    11
    Views
    237

    [General] Not sure if it has thermal protection but I've...

    Not sure if it has thermal protection but I've fount window motors in many other cars that those thermal protection "switches" fail a lot.
  2. Replies
    16
    Views
    1,405

    [Electrical] Your probably just stalling the motor and the...

    Your probably just stalling the motor and the lift mechanics are not slipping. Not a good thing to keep it stalled with power on.
  3. Replies
    6
    Views
    218

    [Heat & A/C] Leak testing with Nitrogen is usually done at...

    Leak testing with Nitrogen is usually done at much higher pressures. 300 to 400 PSI is not exceeding the burst of hose and components. I think the high pressure switch is set to 450 PSI. With the...
  4. [For Sale] All you need to do is make sure there is a little...

    All you need to do is make sure there is a little play at the top of the pedal. I don't see why people had problems with the adjustable link. I guess they wanted the pedal at the same height as the...
  5. Replies
    16
    Views
    1,405

    [Electrical] There is no automatic shut off on the windows. ...

    There is no automatic shut off on the windows. You have to release the switch when the window has stopped moving. I could design one that would sense the electrical current change but I would guess...
  6. Replies
    4
    Views
    113

    [Engine] I removed mine for the same rattle and have had...

    I removed mine for the same rattle and have had no problems. I have stock exhaust. I seem to remember the stove is above the exhaust so it's not protecting the starter if so.
  7. Replies
    16
    Views
    1,405

    [Electrical] Is the switch an original or who's new one? You...

    Is the switch an original or who's new one? You can plug the other window switch into the bad side and see if the window motor is still working.
  8. Replies
    8,482
    Views
    1,593,306

    [General] It could be your deceleration springs/valves are...

    It could be your deceleration springs/valves are shot. Many cars have this problem which cause the high RPM idle after warmup.
  9. [General] The front of the plate is held down by the AC...

    The front of the plate is held down by the AC plastic face. The back is held down by two screws that screw into clips on the "U" metal plate. Do you mean the sides are popping up?
  10. Replies
    18
    Views
    569

    [Heat & A/C] +1 Looks like you have no other options but to...

    +1
    Looks like you have no other options but to measure the current. Not many multimeters work above 10 amps so you need to find a DC clamp on type current meter. You just lamp it over the one wire...
  11. Replies
    4
    Views
    323

    [Electrical] With incandescent bulbs you can not use the cold...

    With incandescent bulbs you can not use the cold resistance to compute current. That is the peak current you will get for an instant when first turned on but quickly as the filaments heat the...
  12. Replies
    8,482
    Views
    1,593,306

    [General] I have been running without the bracket for many...

    I have been running without the bracket for many years now.
  13. Replies
    30
    Views
    1,157

    [Frame & Body] Yes, I had most of mine also pulled right to the...

    Yes, I had most of mine also pulled right to the ty-wrap ends hitting the washers.
  14. Replies
    6
    Views
    2,698

    I just thought of a way to test the tank and the...

    I just thought of a way to test the tank and the check valve. After shutting the engine off, see how many times you can switch from one mode to another and stop hearing the actuators and flaps work....
  15. Replies
    13
    Views
    466

    [Electrical] By the way, it takes a long drive to charge a...

    By the way, it takes a long drive to charge a battery that is quite low on charge. If your car sits 3 months and still has the door lock ECU and clock connected it will be about half charged.
  16. Replies
    18
    Views
    569

    [Heat & A/C] You should see close to battery voltage. If your...

    You should see close to battery voltage. If your only seeing 5 volts than your circuit breaker of a bad connection is probably dropping the voltage. What does your dash voltage gauge read with the...
  17. Replies
    18
    Views
    569

    [Heat & A/C] Speeds 3 and 4 run though two relays used to...

    Speeds 3 and 4 run though two relays used to reduce current through the fan switch. Speed 4 runs power directly to the blower (no resistor).
  18. Replies
    30
    Views
    1,157

    [Frame & Body] What I did was put the 14 gauge fence wire at the...

    What I did was put the 14 gauge fence wire at the sew seam and fold the cover over on that seam. Then I start pulling the ty-wraps tight, turn the seat over and work the cover to the back, tighten...
  19. Replies
    30
    Views
    1,157

    [Frame & Body] Well here is the bottom of the passenger seat. ...

    Well here is the bottom of the passenger seat. This one seems looser than the drivers seat. I even used ty-wraps so it pulled tighter than hog rings. I still have to attach the sides but as you...
  20. Replies
    0
    Views
    246

    DMCH was shown on Texas Metal show

    Last night I was watching Texas Metal which is one of the many car build shows on my favorite TV channel. They modified a classic El Camino with what the customer asked for (A 2075 year interior). ...
  21. Replies
    30
    Views
    1,157

    [Frame & Body] I attached the plastic parts with hog rings like...

    I attached the plastic parts with hog rings like the original covers were attached. That will keep the seat back tight in the middle.
  22. Replies
    30
    Views
    1,157

    [Frame & Body] The plastic is made with the cloth so it will not...

    The plastic is made with the cloth so it will not pull off the cloth. You can buy that material for people that are sewing there own seat covers. The L-seat covers have that only on the back where...
  23. Replies
    42
    Views
    1,857

    [General] I measured it after the seat cover was installed...

    I measured it after the seat cover was installed and the bottom (side to seat) is 2 3/4" and the top edge of the steel latch is a little more at 2 7/8". The OEM cover the cut bottom screw hole is...
  24. Replies
    42
    Views
    1,857

    [General] Well I forgot to take into account for the foam...

    Well I forgot to take into account for the foam getting compressed a little. So my cut at 3" from the edge should have been about 2.75". So remember that when your ready to make your cut.

    Well...
  25. Replies
    42
    Views
    1,857

    [General] Measuring the cut location

    This is how you measure where to make you cut. After finishing the other side so you know where the edge of the skin should sit, you use a tape measure to locate your cut location. Remember the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4