FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: DMC-81

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Thanks Patrick. I sent a PM.

    Thanks Patrick. I sent a PM.
  2. Hi John, I may have the sailing dates and a...

    Hi John,

    I may have the sailing dates and a photo of some pages of the manifest. I'll see if I can dig them up and send them to you. My car was on that ship too, so I'm interested in this...
  3. [General] Thank you. It works really well for me. Yeah, you...

    Thank you. It works really well for me. Yeah, you shouldn't have any fuel smell with this kit. I have an early version aluminum blanking disc to cover where the fuel sender goes. I think they are...
  4. [General] That's good that you changed the fuel injection...

    That's good that you changed the fuel injection lines. I would also recommend upgrading to the all in one fuel pump module. I'm all for keeping it stock usually but this is one area where I made the...
  5. Replies
    23
    Views
    2,268

    Nice. It's looking good!

    Nice. It's looking good!
  6. [For Sale] PM'ed

    PM'ed
  7. Replies
    24
    Views
    2,018

    [Transmission 5-Speed] You are quite welcome.

    You are quite welcome.
  8. Replies
    24
    Views
    2,018

    [Transmission 5-Speed] Hi there, Here is where it is located (red...

    Hi there,

    Here is where it is located (red arrow):

    http://dmctalk.org/attachment.php?attachmentid=66958&d=1627930597

    Here is the part number:...
  9. Replies
    38
    Views
    4,977

    [Suspension] If your AVO washers are still good, you don't...

    If your AVO washers are still good, you don't need washer 109089. I confirmed that these are identical to the AVO washers and the rubber replacement bushings fit nicely with them.
    The front bushings...
  10. Replies
    38
    Views
    4,977

    [Suspension] I agree. I installed polyurethane bushings on my...

    I agree. I installed polyurethane bushings on my V8 Fiero 20+ years ago, and in terms or ride quality, I forgot how harsh they were. I test drove the DeLorean today after the work, and like Tillsey...
  11. Replies
    38
    Views
    4,977

    [Suspension] AVO Polyurethane bushing failure

    Well, I'll add my experience to this thread.
    I also suffered top polyurethane bushing failure in July 2021 on AVO shocks installed in September 2015. It has been almost 6 years, but only 3,000...
  12. Replies
    7
    Views
    4,430

    [General] Thanks, and you're welcome. Good luck with the...

    Thanks, and you're welcome. Good luck with the refurb. :thumbup:
  13. Replies
    7
    Views
    4,430

    [General] Sorry, I missed your location question. At least...

    Sorry, I missed your location question. At least the high pressure switch wire comes out behind the AC accumulator from the passenger footwell. You can see photos and commentary beginning on post...
  14. Replies
    6
    Views
    389

    [Electrical] I had the car die on me during my early shakedown...

    I had the car die on me during my early shakedown tests after I restored it and it was the same cause. For mine, it was the double connector on the right wire.
    ...
  15. Replies
    7
    Views
    4,430

    [General] For the high pressure switch, there's a 16"...

    For the high pressure switch, there's a 16" version and a longer version at DeLorean.com. It looks like you possibly have the shorter version. Perhaps the low pressure switch wire is the...
  16. [Fuel] For both sizes, it looks like the maximum torque...

    For both sizes, it looks like the maximum torque spec is 13 in lbs. (Inch pounds), but I would verify with the manufacturer of the clamps you buy. I always torque to spec on any fastener and I...
  17. [Fuel] Cool. Good luck. Make sure you torque the fuel...

    Cool. Good luck. Make sure you torque the fuel injection clamps properly.
  18. [Fuel] Here is the information from when I did the job:...

    Here is the information from when I did the job:

    http://dmctalk.org/showthread.php?14488-Fuel-Accumulator-Removal/page2

    http://dmctalk.org/showthread.php?12923-Fuel-hose-diameter
  19. Replies
    12
    Views
    2,024

    [Suspension] In that case, I would check with your nearest DMC...

    In that case, I would check with your nearest DMC franchise location, P.J. Grady, Delorean Northwest (Toby), Delorean Go or DeLorean Europe.
  20. Thread: Tinted glass

    by DMC-81
    Replies
    31
    Views
    3,312

    [Frame & Body] Cool. Yes, the sun is really hot on the dash....

    Cool. Yes, the sun is really hot on the dash. Even with the tint, I use a DashMat dash cover all the time. My binnacle and dash is original and pristine, so I protect it as much as possible. I also...
  21. [Engine] You're welcome. Lol. I haven't yet. :) Due to...

    You're welcome. Lol. I haven't yet. :)

    Due to the inherent vibration on the starter, I applied blue loctite. Considering the lubrication of the threadlocker, I probably applied closer to Ron's...
  22. [Engine] I'll defer to Ron's advice.

    I'll defer to Ron's advice.
  23. Replies
    12
    Views
    2,024

    [Suspension] Yes, I have direct experience with them. I bought...

    Yes, I have direct experience with them. I bought a KYB set in 2014 from SpecialT/John Hervey complete with the "shock collars" in your picture. After they arrived, they didn't seem like a safe...
  24. [Engine] Hi Jonathan, I used 21 ft/lbs. (Source M:02:04 )...

    Hi Jonathan, I used 21 ft/lbs. (Source M:02:04 )
    66586
  25. Replies
    12
    Views
    711

    [General] Agreed. Caldwell, ID. Such a shame.

    Agreed. Caldwell, ID. Such a shame.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4