Location: Reedsburg, WI
Posts: 4,026
My VIN: 5180
Club(s): (DMWC) (DCUK)
DENNIS
VIN 5180, Frame 3652, STAGE II, DM-eng Solid State Solutions (RPM Rly, Dm.Lt.Mod., Fan Fail Mod. , FAN Rly, HS.Rly) , HID headlights, SPAX user since 2009, Eibach springs, M Adj. Rear LCA's, DPNW poly-sway bar kit, DMCEU LCA Stabilizer link kit, DMCMW Illuminated door sills, Aussie Illuminated SS Shifter plate, REAL MOMO EVO Steering wheel, DELOREANA Extended View Side Mirrors w/ Heaters, DELOREANA LED Door Lights.
One thing I noticed about the DMCH reproduction is that it's more of a hybrid between versions 5 and 6.
Version 5 is the only one that has the red and blue bars on the "Bi Level" indicator incorrectly swapped so that blue is on top. This was fixed in version 6, and the words Heat and Cool were also removed from the temp setting dial.
DMCH's reproduction has the Version 5 incorrect blue over red indicator for Bi Level mode, but has the Version 6 temp setting dial without the wording. Its hard to tell but it also looks like the size of the text is a little smaller, and the symbols are a bit larger, especially the defrost indicator.
DMCH Repro:
.
.
.
Versions 5 and 6 for comparison:
Last edited by Mark D; 10-30-2015 at 09:49 AM.
I've got one of the new DMCH decals on order but for some reason they are not shipping yet. When I get it, I can compare the results with my LED board.
Dave M vin 03572
http://dm-eng.weebly.com/
Location: Reedsburg, WI
Posts: 4,026
My VIN: 5180
Club(s): (DMWC) (DCUK)
I don't know if there is a set industry standard.
How I look at it is:
Bi-level is the location of the air source.
Upper vents typically blow cold air (blue)
Lower floor vents blow hot air (red)
To me the temperature arcs are backwards. The arcs should be mirrored
Cold on left (under) hot on right (over)
Rotate the dial CCW to turn down the temp and rotate CW to turn up the temp.
I guess it's just the perspective of how I see things in a logical way.
There is no right or wrong, the mechanics of the system are what they are.
If l was the designer of the system, I would change the temperature control. I'm sure back in the day, not much thought was given to it. The designers just used off the shelf mechanicals.
Dennis
DENNIS
VIN 5180, Frame 3652, STAGE II, DM-eng Solid State Solutions (RPM Rly, Dm.Lt.Mod., Fan Fail Mod. , FAN Rly, HS.Rly) , HID headlights, SPAX user since 2009, Eibach springs, M Adj. Rear LCA's, DPNW poly-sway bar kit, DMCEU LCA Stabilizer link kit, DMCMW Illuminated door sills, Aussie Illuminated SS Shifter plate, REAL MOMO EVO Steering wheel, DELOREANA Extended View Side Mirrors w/ Heaters, DELOREANA LED Door Lights.
That's a good point about the actual function of the bi-level mode. I had to re-read the users manual to try and figure out which would actually be correct. This is the text from the manual:
It sounds like blue on the top may somewhat correct, although the original drawings for the A/C label do show it as red over blue being correct. You could really interpret it both ways:BI-LEVEL - In this position and with the temperature control in mid-position, conditioned air is provided to he face level and door vents while conditioned warmer air is provided to the footwells and a lesser amount to the windscreen, Adjusting the temperature control will vary the temperature accordingly.
Warm on top from the windscreen vent, cool on bottom for the face and door vents.
OR
Cool on top for the face and door vents, warm on bottom for the footwell vents.
Location: Lansing, MI
Posts: 490
My VIN: 04194: 5-Speed, Black Int, 79 Peugeot 604 Manifold, 05052: 5-Speed, Gray Int, 78 Peugeot 604 manifol
PM sent!
Andrew
4194 Since 7/98
5052 Since 7/14
1972 Buick Riviera
1974 Bricklin SV-1 177
1982 AMC Eagle SX/4 (4.2 I6, 4 Speed)
1983 Pontiac Trans Am (Knight Rider Conversion in progress)
1985 Oldsmobile Toronado (daily driver)
Solex carb and antenna television guru.
"My carbon footprint is bigger than yours!" :-)