Location: Reedsburg, WI
Posts: 4,026
My VIN: 5180
Club(s): (DMWC) (DCUK)
Last edited by DMC5180; 12-04-2016 at 06:08 PM.
DENNIS
VIN 5180, Frame 3652, STAGE II, DM-eng Solid State Solutions (RPM Rly, Dm.Lt.Mod., Fan Fail Mod. , FAN Rly, HS.Rly) , HID headlights, SPAX user since 2009, Eibach springs, M Adj. Rear LCA's, DPNW poly-sway bar kit, DMCEU LCA Stabilizer link kit, DMCMW Illuminated door sills, Aussie Illuminated SS Shifter plate, REAL MOMO EVO Steering wheel, DELOREANA Extended View Side Mirrors w/ Heaters, DELOREANA LED Door Lights.
Location: West Sayville, N.Y.
Posts: 1,350
My VIN: 005058 000927
Club(s): (AZ-D) (DMA) (DOA) (DCUK)
Thanks again Dennis! Those pictures and techniques are very helpful.
Today I drained the gear oil for (the second time in a month.... so the inside should be clean), and removed the drive axles. The first one took over an hour as I used a normal ratchet on the M10 bolts, and the outboard side was stuck after I removed the bolts. I eventually I took a piece of 2x2 wood and placed it on the thick metal disc that the bolts pass through. Then I tapped the wood sharply with a hammer. The axle broke free from the flange after that, so it was just stuck.
The second axle only took 10 minutes as I used an air impact wrench, and the tapping technique to release it.
2 of the 4 boots were cracked at the outboard bigger clamp, so their refurbishment is just in the nick of time.
image.jpg
Question: were the axles painted originally? If so, was it gloss or satin black? I see the picture on DMC's website seems to indicate black paint.
Dana
1981 DeLorean DMC-12 (5 Speed, Gas Flap, Black Interior, Windshield Antenna, Dark Gray)
Restored as "mostly correct, but with flaws corrected". Pictures and comments of my restoration are in the albums section on my profile.
1985 Chevrolet Corvette, Z51, 4+3 manual
2006 Dodge Magnum R/T (D/D)
2010 Camaro SS (Transformers Edition)
Location: Reedsburg, WI
Posts: 4,026
My VIN: 5180
Club(s): (DMWC) (DCUK)
Dana,
You know the thing to do is disassemble them and have the shafts powder coated satin black. You just mask off what doesn't get coated.
Sent from my iPhone using Tapatalk
Last edited by DMC5180; 12-04-2016 at 08:42 PM.
DENNIS
VIN 5180, Frame 3652, STAGE II, DM-eng Solid State Solutions (RPM Rly, Dm.Lt.Mod., Fan Fail Mod. , FAN Rly, HS.Rly) , HID headlights, SPAX user since 2009, Eibach springs, M Adj. Rear LCA's, DPNW poly-sway bar kit, DMCEU LCA Stabilizer link kit, DMCMW Illuminated door sills, Aussie Illuminated SS Shifter plate, REAL MOMO EVO Steering wheel, DELOREANA Extended View Side Mirrors w/ Heaters, DELOREANA LED Door Lights.
Let us reply to ambition that it is she herself that gives us a taste for solitude.
Well, it's been a while. I disconnected most things to remove the gearbox but didn't feel confident to actually remove it by myself. I knew I needed help.... Then I got the fantastic news that DMCFL was moving to Orlando. So, I decided to wait.
On the weekend I delivered my baby to Tony and his familiar team to get that help.
image.jpg
Wow, the construction/ finish work is coming along, and looks awesome! It's just like I'd do it in my perfectionistic tendencies. It's like my Stainless icon is in its second home. The place was filling up fast with cars. The tow truck driver said "it looks like they're collecting DeLoreans!"
Thanks Tony and team!
P.S. Lenny, your car looks great!
Now I can continue this thread...
Dana
1981 DeLorean DMC-12 (5 Speed, Gas Flap, Black Interior, Windshield Antenna, Dark Gray)
Restored as "mostly correct, but with flaws corrected". Pictures and comments of my restoration are in the albums section on my profile.
1985 Chevrolet Corvette, Z51, 4+3 manual
2006 Dodge Magnum R/T (D/D)
2010 Camaro SS (Transformers Edition)
With my starter and exhaust refurbed already, I focused on the drive axles while my car is queued for attention at DMCFL.
After great informational posts here warning about a messy job on the CVs, I set up a table with a plastic sheet to control the grease as I refurb them...also gloves, many paper towels, and a garbage can nearby. I used a small piece of 1x2" wooden block ( to avoid damage) and a hammer to remove the flange/cover. It was sealed with blue Hylomar, and after I removed it, I gently scraped its residue off both parts.
image.jpg
I used this reference photo to reassemble the joint later... i.e. how the inner race aligns with the outer race, thin versus thick edges, etc.
image.jpg
I used a pair of snap ring pliers and a pick to remove the snap ring. The inner race came off the axle easily, and I separated the parts. After I wiped most of the grease off the parts I then bathed them in mineral spirits twice.
image.jpg
Clean parts. I scrubbed the flanges with a blue Scotch Brite pad...
image.jpg
I cleaned up the area and organized my parts for assembling the CV joints.
image.jpg
Rich_NYS pointed this out for me in his resto thread...for the inner races, the smooth side on the left butts against the snap ring, and the other side on the right with the raised area butts against the axle.
image.jpg
One CV dry assembled. I paid attention to the proper orientation of the inner and outer races, and made sure that the smooth side of the inner race was facing me...
image.jpg
And so on. I bagged and tagged each joint's parts to keep them in the same spot on the car...
image.jpg
The next step was refurbing and painting the axle rods. I must say that this whole task would be fairly daunting without great resources here, and other owners who have shared their experiences. Thanks all!
Last edited by DMC-81; 03-09-2017 at 08:17 PM.
Dana
1981 DeLorean DMC-12 (5 Speed, Gas Flap, Black Interior, Windshield Antenna, Dark Gray)
Restored as "mostly correct, but with flaws corrected". Pictures and comments of my restoration are in the albums section on my profile.
1985 Chevrolet Corvette, Z51, 4+3 manual
2006 Dodge Magnum R/T (D/D)
2010 Camaro SS (Transformers Edition)
Location: Orlando, FL
Posts: 1,181
My VIN: Former owner of 1098
Club(s): (DCF)
Few jobs on this car are as messy and give you a sense of accomplishment as re-doing the CV joints. Nice work so far!
Brandon S.
2014 Honda Civic EX
2007 Volvo S60R
Location: Orlando, Florida
Posts: 2,734
My VIN: 01643
Club(s): (DCF) (DCO) (DCUK)
I expected to see far more grease all over the place. Something a little more like this (my CV rebuild aftermath) CV Joints.jpg
I'll never figure out how you always manage to keep everything so clean and tidy! Very well done!!
Location: NYS
Posts: 2,511
My VIN: 4519