Page 1 of 2 1 2 LastLast
Results 1 to 10 of 18

Thread: Oil Change help

  1. #1
    Senior Member QuadcityDMC's Avatar
    Join Date:  May 2011

    Location:  Moline,IL

    Posts:    132

    My VIN:    3390

    Oil Change help

    I'm pulling the Delorean out in a few weeks. I need to change the oil and coolant, this will be my first time doing this by myself. I have a 2011 stage 2 motor, what is the recommended oil and filter? What is the recommended coolant as well? Thanks.

  2. #2
    Senior Member mr_maxime's Avatar
    Join Date:  Mar 2015

    Posts:    710

    My VIN:    10201

    valvoline vr1 20w-50 for oil, bosch model 3421 works for oil filter, oreillys conventional green coolant. you will need the square plug tool before draining the oil though if you have the stock drain plug. you will also need copper washer. so youre best off buying the tool from dmc and picking up a pack of filters that come with the washers.

  3. #3
    Member
    Join Date:  Aug 2015

    Location:  Fallbrook, CA (North San Diego County)

    Posts:    36

    My VIN:    SCEDT26T4DD016387

    Club(s):   (DOA) (NCDMC) (DCUK)

    Okay... I need the square Oil Plug tool. I can't find it on the DMC site. Any ideas as to where I can find one? Is there a size I can ask for at a local tool or auto parts store?

  4. #4
    Mostly Harmless... refugeefromcalif's Avatar
    Join Date:  Aug 2012

    Location:  Duncanville, Alabama USA

    Posts:    803

    My VIN:    6599

    It's an 8mm square male socket.
    Funny, I don't find it on the DeLorean website now either.

    George
    George.



    1974 BMW RS90 motorcycle
    1981 DeLorean. Cruise Control, Wings-A-Loft, Eibach springs, Spax shocks, Stage1 exhaust, Manual, Grey and Grooved, LED clock and fixed pulls.
    1993 del Sol S (With a Few, Upgrades)
    2017 Chrysler Pacifica Limited

  5. #5
    Junior Member
    Join Date:  Apr 2017

    Location:  Madison, WI

    Posts:    19

    My VIN:    02530

    It's 5/16 which should be available at most part stores. Or DMC #111104

  6. #6
    DMC Midwest - 815.459.6439 DMCMW Dave's Avatar
    Join Date:  May 2011

    Location:  Crystal Lake IL

    Posts:    4,967

    My VIN:    05429

    http://store.delorean.com/p-9097-drain-plug-socket.aspx

    You can chase down a snap-on truck but they never carry it on the truck. Special order.
    Dave S
    DMC Midwest - retired but helping
    dswingle@DeLorean.com

  7. #7
    Delorean Guru
    Join Date:  May 2011

    Location:  Northern NJ

    Posts:    5,871

    My VIN:    10757

    Club(s):   (DMA)

    Quote Originally Posted by DMCMW Dave View Post
    http://store.delorean.com/p-9097-drain-plug-socket.aspx

    You can chase down a snap-on truck but they never carry it on the truck. Special order.
    If necessary you can buy a short piece of 5/16 square stock and put a bend in it so it looks like an allen wrench. While you can reuse the old copper gasket it is best if you replace it. You should get the motor up to operating temperature before draining the oil. The coolant you drain cold. To do it properly you should drain each individually, the motor, the heater core, and the radiator. Flush with clean water, dump that and repeat til it comes out clear. Drain as much as you can then refill with 50/50 soft water and anti-freeze. Takes about 3-1/2 to 4 gallons so you need 2 gallons of anti-freeze. The good old green stuff (Prestone) is fine. As long as you are doing fluids, check the transmission level and flush the brakes and clutch. Another thing to check is the washer fluid bottle. If it hasn't been touched in a long time you should take the bottle out and wash it out with hot water. On my car it was filled with slime. The other filters are the air filter and the fuel filter if they haven't been changed in a long time.
    David Teitelbaum

  8. #8
    TGTF (Too Greek to Function) AugustneverEnds's Avatar
    Join Date:  Jul 2012

    Location:  Syracuse, NY area

    Posts:    666

    My VIN:    SCEDT26T5CD010287

    Club(s):   (DMA)

    I recommend using the thinnest head ratchet you have with the square drive socket. The space between the drain plug and the frame is limited. I always take a bit of aluminum foil and wrap it around the frame cross-member to protect it from the waterfall of black oil that will be rushing out. Bosch carries a filter that is a smaller diameter than other brands, a bit easier to install and remove later, no rubbing up against the oil sender.
    Nick A.
    Νικος Αυγουστινατου

    1988 BMW 325iS
    1982 DeLorean DMC-12

  9. #9
    Stuck in the 80s John U's Avatar
    Join Date:  May 2011

    Location:  Kitchener, Ontario

    Posts:    503

    My VIN:    3462

    Club(s):   (DOI)

    Good time to change the plug for something like this

    https://www.ebay.com/itm/371199922297

  10. #10
    Stuck in the 80s John U's Avatar
    Join Date:  May 2011

    Location:  Kitchener, Ontario

    Posts:    503

    My VIN:    3462

    Club(s):   (DOI)

    Also a good time to change the oil pressure sender if you have an old one

Page 1 of 2 1 2 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •