FRAMING JOHN DELOREAN - ON VOD
www.framingjohndeloreanfilm.com
-
Senior Member
Time for a clutch replacement?
Recently my car seems to be exhibiting symptoms of a clutch disc that may be on its way out. When in gear and pressing the gas, the RPMs are climbing higher, but the car's speed is increasing at a much slower pace. It's very noticeable that acceleration is weaker, especially when going up an incline. As a test I pulled the handbrake and put the car in 3rd gear, when I let up on the clutch pedal, the car did not stall. I've also noticed the clutch is now engaging at the very top of the pedal travel. In other words, I have to let off the clutch pedal almost all the way before it finally connects.
I checked my reservoir and it is full, zero leaks under the car, and in the driver's footwell where the master cylinder goes through the firewall is bone dry. The master and slave cylinders and the stainless steel line were installed by DMC-CA a couple years ago. As far as I know the clutch is original. Since I've owned the car, I've always taken it easy with the clutch and the car isn't high mileage by any means, so failure seems premature, but again there's no way of really knowing how much abuse it's seen in its lifetime, from previous owners before I acquired it.
I'm almost certain this is a clutch issue and not hydraulics. But this is a huge job, so before I call it, is there anything else I can check?
Has anyone else experienced these symptoms before and found it was something other than the clutch?
Thanks
Last edited by Gregadeth; 06-05-2017 at 05:54 AM.
-
President, DeLorean Industries
I would say that you are correct on the clutch being the issue. Most clutches in our experience are good for about 30k depending on driving habits etc. Are you planning on replacing this yourself or outsourcing the job?
-
Senior Member
Originally Posted by
Gregadeth
Recently my car seems to be exhibiting symptoms of a clutch disc that may be on its way out. When in gear and pressing the gas, the RPMs are climbing higher, but the car's speed is increasing at a much slower pace. It's very noticeable that acceleration is weaker, especially when going up an incline. As a test I pulled the handbrake and put the car in 3rd gear, when I let up on the clutch pedal, the car did not stall. I've also noticed the clutch is now engaging at the very top of the pedal travel. In other words, I have to let off the clutch pedal almost all the way before it finally connects.
I checked my reservoir and it is full, zero leaks under the car, and in the driver's footwell where the master cylinder goes through the firewall is bone dry. The master and slave cylinders and the stainless steel line were installed by DMC-CA a couple years ago. As far as I know the clutch is original. Since I've owned the car, I've always taken it easy with the clutch and the car isn't high mileage by any means, so failure seems premature, but again there's no way of really knowing how much abuse it's seen in its lifetime, from previous owners before I acquired it.
I'm almost certain this is a clutch issue and not hydraulics. But this is a huge job, so before I call it, is there anything else I can check?
Has anyone else experienced these symptoms before and found it was something other than the clutch?
Thanks
When you're traveling up a hill, put the car in a higher gear than you would normally use and floor the accelerator. You should see the RPMs rev up with little or no change in acceleration. If so, the clutch is slipping and on its way out.
-
The only other thing besides a worn out clutch I've seen cause slippage is an adjustable link set up too tight which will preload and partially disengage the clutch. Check for that first before replacing the clutch.
Rob
-
Senior Member
Thanks for the feedback...
Originally Posted by
Delorean Industries
I would say that you are correct on the clutch being the issue. Most clutches in our experience are good for about 30k depending on driving habits etc. Are you planning on replacing this yourself or outsourcing the job?
My mileage is pretty much in that range so I guess it is time after all. I don't really have the resources to do it myself and trans work is a bit out of my league, so I will probably outsource. I have a couple acquaintances that say they can do it, so we'll see.
Originally Posted by
Drive Stainless
When you're traveling up a hill, put the car in a higher gear than you would normally use and floor the accelerator. You should see the RPMs rev up with little or no change in acceleration. If so, the clutch is slipping and on its way out.
It seems to be doing that no matter what gear it's in. When going uphill, revving high in 1st gear does nothing to speed, I imagine it would be the same with higher gears or worse. I'll give this a shot though.
Originally Posted by
PJ Grady Inc.
The only other thing besides a worn out clutch I've seen cause slippage is an adjustable link set up too tight which will preload and partially disengage the clutch. Check for that first before replacing the clutch.
Rob
That's a good point. That's the link that goes on the clutch pedal linkage, right? From what I've seen down there it's all looked stock to me, but I'll double check to make sure.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules