FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 28

Thread: Bosch EV12 injectors?

  1. #1
    '82 T3 FABombjoy's Avatar
    Join Date:  May 2011

    Location:  Lansing, MI

    Posts:    1,168

    My VIN:    10270

    Bosch EV12 injectors?

    Seem like a good candidate for Kjet heads. Anyone ever try?

    I picked up a p/n 280157012 just to eyeball it. They're a fairly easy to find VW/Audi part. 4 hole injector, end cap looks to be the cone-type (not the two spray version) but I haven't ran any fluid through it to double check yet. 26.9lb/hr equivalent - plenty of overhead for power without being expensive.

    Tip is just about at the opening to the intake port, not quite as long as a kjet injector but way closer to the intake path than most others.

    IMAG2539.jpg
    Luke S :: 10270 :: 82 Grey 5-Speed :: Single Watercooled T3 .60/.48 :: Borla Exhaust :: MSD Ignition :: MS3X Fully SFI Odd-fire EFI :: DevilsOwn Methanol Injection

  2. #2
    LS Swapper Josh's Avatar
    Join Date:  Mar 2013

    Location:  Illinois

    Posts:    2,440

    My VIN:    11408

    Club(s):   (DMWC) (TXDMC) (DCUK) (DOI)

    They look very similar to EV1/EV6 injectors I have used in the past, with the exception of the actual injection point on the bottom. the ev12s stick out very far.
    If you are after a compact injector (height) I would suggest the 99+ Gm truck injectors. They are basically a stubby EV6

    Supercharged 5.3L LS4 + Porsche 6spd
    [email protected]
    lsdelorean.com
    I am not affiliated with Delorean Midwest in anyway.

  3. #3
    '82 T3 FABombjoy's Avatar
    Join Date:  May 2011

    Location:  Lansing, MI

    Posts:    1,168

    My VIN:    10270

    They do seem like they will fit. I will probably have to swap one of the compressor bracket bolts for either a smaller head or an allen head. Or just remove it entirely since there are 3 other bolts and a belt to hold it in place Could install injector extension caps too but they're probably not needed.

    I'mma gonna use 'em, we'll see how it goes!
    Luke S :: 10270 :: 82 Grey 5-Speed :: Single Watercooled T3 .60/.48 :: Borla Exhaust :: MSD Ignition :: MS3X Fully SFI Odd-fire EFI :: DevilsOwn Methanol Injection

  4. #4
    President, DeLorean Industries
    Join Date:  May 2011

    Location:  CLE/PHX

    Posts:    2,588

    My VIN:    5646,5080, 5880, 10234, 3639, 2518, 10586, 1538

    We use that body style on our builds.
    www.deloreanindustries.com Every Detail Matters

  5. #5
    '82 T3 FABombjoy's Avatar
    Join Date:  May 2011

    Location:  Lansing, MI

    Posts:    1,168

    My VIN:    10270

    I appreciate that you are willing to share that 😊
    Luke S :: 10270 :: 82 Grey 5-Speed :: Single Watercooled T3 .60/.48 :: Borla Exhaust :: MSD Ignition :: MS3X Fully SFI Odd-fire EFI :: DevilsOwn Methanol Injection

  6. #6
    Senior Member Drive Stainless's Avatar
    Join Date:  Mar 2016

    Posts:    576

    It really helps to keep the intake valves cleaner if the injectors spray onto them instead of the conventional Kjet design. Like night and day difference.

  7. #7
    '82 T3 FABombjoy's Avatar
    Join Date:  May 2011

    Location:  Lansing, MI

    Posts:    1,168

    My VIN:    10270

    So does meth injection!
    Luke S :: 10270 :: 82 Grey 5-Speed :: Single Watercooled T3 .60/.48 :: Borla Exhaust :: MSD Ignition :: MS3X Fully SFI Odd-fire EFI :: DevilsOwn Methanol Injection

  8. #8
    President, DeLorean Industries
    Join Date:  May 2011

    Location:  CLE/PHX

    Posts:    2,588

    My VIN:    5646,5080, 5880, 10234, 3639, 2518, 10586, 1538

    We use a much higher lb rating though.
    www.deloreanindustries.com Every Detail Matters

  9. #9
    Not a DeLorean Guru
    Join Date:  May 2011

    Location:  Rochester, NY

    Posts:    2,405

    My VIN:    01049

    Quote Originally Posted by FABombjoy View Post
    So does meth injection!
    walter white.jpg
    -Mike

    My engine twists my frame.

    1981 DeLorean, Carb LS4 swap completed
    1999 Corvette, cam/headers/intake manifold, 400 rwhp
    2005 Elise, stock
    2016 Chevy Cruze

  10. #10
    '82 T3 FABombjoy's Avatar
    Join Date:  May 2011

    Location:  Lansing, MI

    Posts:    1,168

    My VIN:    10270

    Quote Originally Posted by Delorean Industries View Post
    We use a much higher lb rating though.
    It's not the size of the injector, it's how you use it

    Quote Originally Posted by opethmike View Post
    "I love meth. Methy meth meth. Here it goes down, down into my motor." -Walter Burgundy
    Luke S :: 10270 :: 82 Grey 5-Speed :: Single Watercooled T3 .60/.48 :: Borla Exhaust :: MSD Ignition :: MS3X Fully SFI Odd-fire EFI :: DevilsOwn Methanol Injection

Page 1 of 3 1 2 3 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •