FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 13

Thread: Fuel leak pouring out the bottom of car

  1. #1
    Senior Member bfloyd's Avatar
    Join Date:  Nov 2014

    Location:  Lebanon, Tennessee

    Posts:    389

    My VIN:    3294

    Fuel leak pouring out the bottom of car

    Took my car to the local Cubscout camp over the weekend for a static display for their "time traveling" theme weekend resident camp. Easy money, just stand around and keep boys out of your car. As I was pulling out and leaving, I can't tell if I ran over something or what but the engine just completely died and I coasted to a stop on the shoulder of the paved camp road. I tried cranking and cranking and never could get it to restart. As I was cranking it, the cabin started filling up with gasoline fumes. I got out and opened the engine bay and checked all of the fuel line connections to the fuel distributor and frequency valve... they're all good and tight. I could here liquid running out on the ground as I had my head stuck down in the engine bay. I got down on the ground and looked under the car to see gas pouring out in a steady stream about midway of the car - running over both of the cooling pipes along the frame. I had to end up getting towed home and just rolled it into the garage off the flatbed.

    What the hell happened? There shouldn't be any fuel lines in that area unless something has happened to the rubber hoses on the accumulator? Gonna get it up on stands one night this week to see where exactly it's coming from. Any clues?
    Barry Floyd
    Lebanon, Tennessee
    VIN 3294 - Aug. 81

  2. #2
    Senior Member
    Join Date:  May 2011

    Location:  Northern NJ

    Posts:    8,570

    My VIN:    10757 1st place Concourse 1998

    Raise the car and inspect the lines to the fuel accumulator.
    David Teitelbaum

  3. #3
    Stupid Newbie DaraSue's Avatar
    Join Date:  Jul 2016

    Location:  The LC

    Posts:    1,057

    My VIN:    10907

    I had something like that happen once (on the freeway 30 miles north of Cedar City) and it was a clamp that had bottomed out and come loose on a line under the car (iirc it was on the passenger's side). Are you using t-bolt clamps by any chance? That was my issue - apparently that style didn't tighten far enough for these lines. I've since heard that most DeLorean specialists only use the worm-drive ones.
    Last edited by DaraSue; 06-25-2018 at 10:36 AM.

  4. #4
    Senior Member
    Join Date:  Oct 2016

    Location:  Fresno, CA

    Posts:    237

    My VIN:    10353

    I had a leak start where the fuel filter is below the car behind the driver's seat area. Lousy connection there, maybe source of your leak?

    Used pipe thread tape and replaced with new filter fixed it.

  5. #5
    Senior Member DMC-81's Avatar
    Join Date:  Apr 2014

    Location:  Florida

    Posts:    2,371

    My VIN:    <2000

    Club(s):   (DCF)

    Quote Originally Posted by David T View Post
    Raise the car and inspect the lines to the fuel accumulator.
    +1 on this, based on you saying the fuel was coming out in the middle of the car. Many months after my accumulator replacement, I had one of the clamps holding the rubber lines loosen enough to drip, even with proper Fuel Injection clamps. With the confined space, I find you can't really get enough leverage to tighten them too much. Assuming you replaced yours, perhaps you had a line come off completely?
    Dana

    1981 DeLorean DMC-12 (5 Speed, Gas Flap, Black Interior, Windshield Antenna, Dark Gray)
    Restored as "mostly correct, but with flaws corrected". Pictures and comments of my restoration are in the albums section on my profile.
    1985 Chevrolet Corvette, Z51, 4+3 manual
    2006 Dodge Magnum R/T (D/D)
    2010 Camaro SS (Transformers Edition)

  6. #6
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,096

    My VIN:    5003 Never placed Concourse

    Club(s):   (DCF)

    Any fuel lines I have to secure, I now use ear / pinch clamps to secure them. I doubt this will apply to the accumulator given the amount of space you have to work in, but the next best thing to do is use a small 1/4" ratchet with the proper socket in there to tighten a screw/worm clamp down. Don't over-tighten or the clamp will break.
    -----Dan B.

  7. #7
    Senior Member bfloyd's Avatar
    Join Date:  Nov 2014

    Location:  Lebanon, Tennessee

    Posts:    389

    My VIN:    3294

    Assuming you replaced yours, perhaps you had a line come off completely?
    Yes, I replaced my accumulator and both rubber hoses back in the summer of 2015. Since it was coming out at a steady stream instead of a spraying pattern, I'm thinking it may have come completely off. I'm off from work on Tuesday and Wednesday nights, I'll crawl under there and see what I can find.
    Barry Floyd
    Lebanon, Tennessee
    VIN 3294 - Aug. 81

  8. #8
    Motors about after dark Michael's Avatar
    Join Date:  May 2011

    Posts:    4,761

    My VIN:    Your VIN'S mom

    Because of the closing plate holding/hiding the true source, the leak could be almost anywhere in that area. I would start at the pump itself. I could almost guarantee you a fitying has backed off a little and it doesnt take much to leak. I had the same issue and I got lucky as it was the first place I looked, the cap/banjo bolt fitting directly on top of the pump. Being midway, the accumulator area is a PITA to access but you can get to those fittings on top of the accumulator by removing the center console. There is a small rectangular cover on the underbody that covers the small fittings above the accumulator. (I had a leak there too many years ago. Never leaked but it sure smelled).
    Last edited by Michael; 06-25-2018 at 06:08 PM.

  9. #9
    Senior Member mluder's Avatar
    Join Date:  May 2011

    Location:  Happy Valley, OR

    Posts:    1,709

    My VIN:    4456 - Owner since March 2011

    Club(s):   (PNDC)

    Quote Originally Posted by Michael View Post
    Because of the closing plate holding/hiding the true source, the leak could be almost anywhere in that area. I would start at the pump itself. I could almost guarantee you a fitying has backed off a little and it doesnt take much to leak. I had the same issue and I got lucky as it was the first place I looked, the cap/banjo bolt fitting directly on top of the pump. Being midway, the accumulator area is a PITA to access but you can get to those fittings on top of the accumulator by removing the center console. There is a small rectangular cover on the underbody that covers the small fittings above the accumulator. (I had a leak there too many years ago. Never leaked but it sure smelled).
    +1 on checking the fuel pump cover... I had mine work it's way off on it's own and start sloshing fuel. Plus this is an easy one to get to to rule out first.

    Cheers
    Steve
    Cheers
    Steven Maguire
    #4456


    IT'S A TRAP!!!!!

  10. #10
    Senior Member bfloyd's Avatar
    Join Date:  Nov 2014

    Location:  Lebanon, Tennessee

    Posts:    389

    My VIN:    3294

    Thanks guys for the recommendation on the fuel pump cover. I need to do the DMCH recall test on the pump anyway. I got the card in the mail during the winter, but never got around to doing the test. I'll start there and work my way back.
    Barry Floyd
    Lebanon, Tennessee
    VIN 3294 - Aug. 81

Page 1 of 2 1 2 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •