Location: Illinois
Posts: 2,440
My VIN: 11408
Club(s): (DMWC) (TXDMC) (DCUK) (DOI)
Supercharged 5.3L LS4 + Porsche 6spd
[email protected]
lsdelorean.com
I am not affiliated with Delorean Midwest in anyway.
Location: FL
Posts: 948
My VIN: Early
Mockup was only temporary as I did not want to leave the tranmission down there. The pan is a sideways pan, so it's hard to stabilize the damn thing.
Also, yeah I was definitely leaning towards MIG. I've welded before, but it was for fun, and didn't look very pretty. I'm going to have to practice a bit before I'm ready to weld on the delorean...
As a side note, I'll be receiving my MS3 Pro Evo with 8' harness. I wish I could find a base tune for the vr6. Oh well, I'll probably bring the car to a professional VW tuner with a dynamometer. I have 0 experience with gas tuning. Now if it was diesel, then I'd be all set...
Last edited by 81dmc; 04-18-2019 at 09:10 PM.
Early 81 5spd conversion- DMCH Ground Effects, Double Din, Custom Instrument Cluster, QA1 Suspension, 3.0 PRV with MS3
DMCTalk.org Moderator
Actual snippet of a conversation from Sept 2013:
Me: Eddie, I can't wait to get the car back when you're done with it.
Eddie: Yeah, you'll be able to give the car gas, and it won't be - like - embarrassing....
Location: FL
Posts: 948
My VIN: Early
IMG_20190418_2210460~2.jpgIMG_20190418_2210400~2.jpg
It's a monster, but it will fit nicely once the frame is notched under the right trailing arm mount. Plenty of clearance available for cv axles.
Early 81 5spd conversion- DMCH Ground Effects, Double Din, Custom Instrument Cluster, QA1 Suspension, 3.0 PRV with MS3
Location: FL
Posts: 948
My VIN: Early
Early 81 5spd conversion- DMCH Ground Effects, Double Din, Custom Instrument Cluster, QA1 Suspension, 3.0 PRV with MS3
Location: Parker, TX
Posts: 731
My VIN: #1283
Club(s): (SCDC) (DCUK)
VR6 engine (367 rwhp/377 ftlb); Type T4 turbo; A/R=0.70/0.68; Air-to-air intercooler, Megasquirt MS3 Pro, Manual tranny w/ HD output shaft; Remote mounted oil filter.
Adjustable dampers and ride height springs from QA1/DriveStainless; SS triangulated LCA brackets, boxed in LCAs, PU bushings, ventilated front brake rotors - all from DMCEU; UCAs with -3 deg camber from Reid Performance; 15" rear rims x 4
http://deloreanvr6conversion.blogspot.com
Location: FL
Posts: 948
My VIN: Early
Wasn't feasible as transmission required frame mods, and the only welder I knew to trust for such a task passed away.
With that said, I have since converted to manual, so the swap is back on table for the future . I also pre wired the MS3 Pro for future upgrades . Now I just need to somehow make an adapter plate to UN1.
I still have the parts to build a 12v have the cylinder head, low comp pistons, rings, H beam rods, chains etc. need a block, crank, and cam is all.
Early 81 5spd conversion- DMCH Ground Effects, Double Din, Custom Instrument Cluster, QA1 Suspension, 3.0 PRV with MS3
Location: Parker, TX
Posts: 731
My VIN: #1283
Club(s): (SCDC) (DCUK)
VR6 engine (367 rwhp/377 ftlb); Type T4 turbo; A/R=0.70/0.68; Air-to-air intercooler, Megasquirt MS3 Pro, Manual tranny w/ HD output shaft; Remote mounted oil filter.
Adjustable dampers and ride height springs from QA1/DriveStainless; SS triangulated LCA brackets, boxed in LCAs, PU bushings, ventilated front brake rotors - all from DMCEU; UCAs with -3 deg camber from Reid Performance; 15" rear rims x 4
http://deloreanvr6conversion.blogspot.com