Page 4 of 4 FirstFirst ... 2 3 4
Results 31 to 33 of 33

Thread: A/C Recharge for R12

  1. #31
    LS1 DMC Nicholas R's Avatar
    Join Date:  Jun 2011

    Location:  Orlando, Florida

    Posts:    2,558

    My VIN:    01643

    Club(s):   (DCF) (DCO) (DCUK)

    You should really spend an hour or so watching A/C recharging videos on youtube. You need to understand what you're looking at, and the differences when the engine is running vs. not running, the compressor cycling vs. not cycling, etc., as well as what you should expect from the gauges. There's nothing overly specific to the DeLorean that say you can only get your information from this forum. It's good to ask specifics here, but overall AC theory (which you need to learn) is consistent across all cars.

    The concern you see expressed in this thread is that you will damage something, or worse, hurt yourself. It's not personal. There are extreme pressures at play here. Simply attaching a can of refrigerant to the wrong side of the compressor could cause it to explode in your hand. On a car converted to R134 this is much less of a concern because a low pressure side charging hose wont fit on a high pressure side fitting. However, being that your car is still R12 with the same fittings on both the high and low sides, this is a very real possibility if you don't know what you're doing.

    Similarly, overcharging the system can damage the compressor due to pressure extremes. Charging too fast can damage the compressor, as the liquid can enter the cylinders instead of a gas, and the liquid can also wash out the compressor lubricant. Not having enough lubricant in the system can damage the compressor.

    There are times when you can jump into a car project with no knowledge and learn as you go. This may be one of those cases, but only provided that you understand the risks associated and have done your homework. In the end, no one on this forum is going to take responsibility if you hurt yourself or the car. Only you can be responsible for yours and the car's well being.
    Last edited by Nicholas R; Yesterday at 10:14 AM.

  2. #32
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    4,465

    Club(s):   (SEDOC) (DCUK)

    +1

    Quote Originally Posted by Felix_29 View Post
    Well it is obvious you guys do know more than I do about this. You guys obviously learned this a/c stuff somehow yourselves. How would you feel if someone said to you "Don't do this job yourself" or "take it an a/c shop. seriously". I'm not sure why you feel i'm not capable of learning what you know... I won't learn anything if I keep taking the car into a shop every time it needs something. I'm trying to be learn more about my car and be cautious at the same time. I think i'm doing the right thing by taking it slow and asking questions. I'm not totally green to this. I only lack experience. I thought that was the point of this forum. For owners to help owners. I do appreciate the help I have received on this thread.
    What I think you are missing is that, when the compressor is not running, the pressure depends on the refrigerant's temperature, NOT how much refrigerant there is in the system, as long as there is a minimum amount present; e.g. When allowed to sit and settle to the ambient temperature, one can in the system would show the same pressure as 3 cans would. So, WRT amount, the only thing that the 58psi you read tells you is that there is some there. WRT pressure, it tells you that there is enough for the low pressure switch to send power to the compressor clutch. So, when you turn on the AC, the clutch should be engaging (even if very briefly). If not, the clutch's coil and/or electrical control has a problem...

    OK- Since you said, "I don't understand why my ac is not blowing very cold. The AC belt is turning when the car is on.", I assume the clutch is engaging, else it would not be cold at all. The poor output temps can be caused by anything from too low/high refrigerant charge to vent control. The charge is a good bet, but you would need a set of gauges to safely continue at this point AND get it right, as others have said. If you make a mistake and put more in it, due to the characteristics of refrigerants mentioned etc, it may work fine until a hot day (or future problem) comes along and the resulting overcharge damages something...or someone.

    ...Check out
    the link the Resources Section HERE then get your hands on a set of gauges, and hang in there!

  3. #33
    Senior Member NckT's Avatar
    Join Date:  Jun 2011

    Location:  Yorkshire UK

    Posts:    185

    My VIN:    No. 4068

    Always wear personal protective equipment (PPE) when dealing with refrigerant. Full safety eye goggles that seal around the face is a must at the very least. Refrigerant coming out under pressure can also freeze skin, as well as asphyxiation....

    I'll assume you'll read up on working safely with refrigerant and not take this lightly. You only get one set of eyes....

    Good luck, be safe, be seeing you
    Last edited by NckT; Yesterday at 02:45 PM.
    RIP Rob van de Veer Top bloke

    I say Sir, I must be mad, one loves fixing K-Jet !

    Make sure there's plenty in the tank for the weekend chaps....

Page 4 of 4 FirstFirst ... 2 3 4

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •