Results 1 to 5 of 5

Thread: how to install evaporator/heater core boot?

  1. #1
    Senior Member
    Join Date:  Jul 2012

    Location:  Yardley, PA

    Posts:    162

    My VIN:    16795

    how to install evaporator/heater core boot?

    Is there any trick to getting the evaporator/heater core boot (part# 105847) pulled back over the retaining ring? I've been struggling with if for a couple of hours now. There doesn't seem to be any way to get my fingers into a position where I can get a good enough grip to pull the lip over the ring.

  2. #2
    Daily Driver ssdelorean's Avatar
    Join Date:  May 2011

    Location:  NW Ohio

    Posts:    224

    My VIN:    16506

    Club(s):   (DCO) (DCUK)

    Yeah not fun.
    I've used flat head screwdrivers, plyers and bicycle tire levers before with good results. Probably not the correct tools to use but that's what I had on hand. Heating up the boot may also help it stretch a bit - not sure but worth a try.
    Shannon Y
    www.ohiodeloreans.com
    www.facebook.com/ohiodeloreans
    ---
    1st angle drive - 58,027 miles (20 years) -- original
    2nd angle drive - 48,489 miles (21 years) -- original from donor
    3rd angle drive - 26,572 miles (2 years 3 months) -- DMCH
    4th angle drive - 21,988 miles (1 year 11 months) -- DMCH
    5th angle drive - 7,137 miles (10 months 2 days) -- DMCH
    6th angle drive - OVER 68,971 miles and counting (OVER 7 yr 1 months & counting) -- new Martin Gutkowski unit
    over 213K miles

  3. #3
    Senior Member
    Join Date:  May 2011

    Location:  Norton, MA

    Posts:    628

    My VIN:    767

    My friend helped me do an A/C conversion recently. He's an actual mechanic (as opposed to me, who makes it up as I go along), and after fighting with this for the better part of an hour we agreed that just using the caulk strip you use to re-seal the evaporator box would be just fine to hold down that last corner. I'll be keeping an eye out for leaks, but it seems pretty solid.

    Not the right answer, and I still have to fill the A/C system and drive the car, but I didn't want to spend anymore time on that boot. Hopefully someone else will be able to provide a good answer.

    -- Joe

  4. #4
    Senior Member
    Join Date:  Oct 2016

    Location:  San Diego, CA

    Posts:    163

    My VIN:    10353

    I just struggled with this yesterday replacing my evap. Was trying to go at it alone, best to have someone else to help guide it in from wheel side while you push it from inside the car. I gave up and just folded it back and will end up cutting it and then wrap the two ends around the pipes.

  5. #5
    Senior Member
    Join Date:  Jul 2012

    Location:  Yardley, PA

    Posts:    162

    My VIN:    16795

    To answer my own question...

    After struggling with this for way too long, I put the boot across a reversed woodworking clamp, extended the clamp to stretch out the boot, and let it sit that way for about 20 minutes. Then I quickly took the boot off the clamp and installed it on the car. With the boot stretched out a bit from sitting on the clamp, it only took me a minute with a flat head screwdriver to get it pulled around the lip. After a while it tightened up a and seems to be held on reasonably well.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •