FRAMING JOHN DELOREAN - AT THEATERS THIS WEEKEND & ON VOD www.framingjohndeloreanfilm.com
Results 1 to 9 of 9

Thread: Can anyone do a temp sensor?

  1. #1
    Junior Member
    Join Date:  Aug 2018

    Posts:    3

    Can anyone do a temp sensor?

    Hi all,

    Iím very nearly close to selling the old boy, and the temp needle doesnít move. My best guess is the sensor because the fuse has been replaced and the battery gauge works. Donít want to have to send it ALLLLL the way down to Garden Grove and donít feel comfortable doing it myself. Live in Beaumont 92223.
    Thank you guys for reading.
    Graham

  2. #2
    Junior Member
    Join Date:  Jan 2018

    Location:  Salem or

    Posts:    13

    My VIN:    02785

    Does it sit down at the 6:00 position?

  3. #3
    Senior Member
    Join Date:  May 2011

    Location:  Burnsville MN-Moving to Kalispell MT. in June 20111

    Posts:    817

    My VIN:    2691

    gauge

    Give the left side of the binnacle a whack, sometimes the needle sticks...

  4. #4
    Junior Member
    Join Date:  Jan 2018

    Location:  Salem or

    Posts:    13

    My VIN:    02785

    Every couple months my needle will get stuck and i am able to just touch it with a paper clip through the trip/reset hole

  5. #5
    Senior Member Silverbullet's Avatar
    Join Date:  Jul 2012

    Location:  Brea, CA

    Posts:    592

    My VIN:    3757

    If you went to Garden Grove, you might be surprised, as they moved to Huntington Beach years ago....

  6. #6
    Junior Member
    Join Date:  Aug 2018

    Posts:    3

    Alright so I just started it up again and let it sit idling for about 5-6 mins. I smacked the side, top and bottom of the binnacle a couple times each. The speedo needle flopped a bit but that was about it. Just wanted to see if any of you lads could do a replace before I go bend over (presumably) at the shop. Is there anything else I should check? Stuck thermostat?

  7. #7
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    1,796

    My VIN:    5003

    Club(s):   (DCF)

    Turn the key on and try to use the paperclip through the trip reset hole to tap the needle and see if that works first. I've had my gauge stuck so bad that the paper clip trick was the only way it would reset. Otherwise no, the thermostat is not tied to the gauge at all. If it isn't the gauge then maybe the wire fell off the temperature sensor or the wire is broken somewhere along the line.

    Good luck.
    -----Dan B.

  8. #8
    Senior Member Chris 16409's Avatar
    Join Date:  May 2011

    Location:  Fresno, CA.

    Posts:    1,258

    My VIN:    16409

    Where abouts are you in southern CA? I had to remove the temp gauge section and replace it with a new one. The orange county DeLorean Club organizes tech days. I want to attend the next one. This is something that could be tackled at one of those.
    Last edited by Chris 16409; 09-25-2018 at 09:59 PM.
    Chris Miles

    For Better or Worse I own a DeLorean!
    1983 Grey Manual, VIN #16409, Fresno, California

  9. #9
    Junior Member
    Join Date:  Aug 2018

    Posts:    3

    Iím out in Beaumont near Redlands, Inland Empire. Iíll go to the paper clip next, but I just really donít think Iím gonna get away from this that easy. Fingers crossed. And yeah Iíd go to a Tech day no problem. Where are the details located?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •