FRAMING JOHN DELOREAN - ON VOD
www.framingjohndeloreanfilm.com
-
It is a lot more than just cutting a hose to length and shoving a barbed fitting into a hose. If you don't get the exact correct fitting to use on that specific kind of hose the connection is of very dubious value. Some hose and fittings require a specific tool to hold everything just so to make a proper connection. There is a science to this. If you are really serious about this find a local hose shop like an Aeroquip dealer and get the right stuff. Shops like that will make the hoses up for you so you KNOW it is assembled with the right hose and fittings and done properly. Do that and then compare what it cost to what the vendor's kits cost. I am betting the vendor's kits are a better deal.
-
DMC Midwest - 815.459.6439
Something else to think about with respect to the comparison between the fuel pump/line hoses and the injector hoses. In the main fuel lines, the fuel flow is pretty significant, on the order of a gallon every few minutes since the system is recirculating. This holds the temperature of the hoses near the tank at not much over 120 degrees. (I'm sure Dave M has measured it but I don't recall the number!).
OTOH, the fuel in the individual injector lines is moving very slowly, i.e. only at the rate of consumption of each injector. So not so much cooling effect, therefore the temperature of the fuel in those lines, and the lines themselves, approaches the temperature right on top of the engine. This makes the composition of those lines even more important than the lines at the tank.
Dave S
DMC Midwest - retired but helping
Greenville SC
-
Senior Member
you know what would be interesting to see?
Has any one even routed the hard metal style injector lines that are sometimes used on K-jet systems?
-
Senior Member
Originally Posted by
Parzival
you know what would be interesting to see?
Has any one even routed the hard metal style injector lines that are sometimes used on K-jet systems?
I was thinking about that too.
-
Senior Member
Originally Posted by
DMCMW Dave
Something else to think about with respect to the comparison between the fuel pump/line hoses and the injector hoses. In the main fuel lines, the fuel flow is pretty significant, on the order of a gallon every few minutes since the system is recirculating. This holds the temperature of the hoses near the tank at not much over 120 degrees. (I'm sure Dave M has measured it but I don't recall the number!).
I've been planning to install this, to cool returning fuel, in a duct bringing in cool air from in front of the radiator.
fuelcooler.jpg
-
Senior Member
Originally Posted by
DMCMW Dave
Something else to think about with respect to the comparison between the fuel pump/line hoses and the injector hoses. In the main fuel lines, the fuel flow is pretty significant, on the order of a gallon every few minutes since the system is recirculating. This holds the temperature of the hoses near the tank at not much over 120 degrees. (I'm sure Dave M has measured it but I don't recall the number!).
OTOH, the fuel in the individual injector lines is moving very slowly, i.e. only at the rate of consumption of each injector. So not so much cooling effect, therefore the temperature of the fuel in those lines, and the lines themselves, approaches the temperature right on top of the engine. This makes the composition of those lines even more important than the lines at the tank.
I did measure with two therm o-couples the fuel temp leaving the tank and fuel temp returned to the tank. It was about 1 deg.F warmer on the return temps. So I concluded that most of the fuel heating was due to the returned fuel. I did have the hot air dam on my car and the tank temps would easily get to 125 deg.F and then my fuel pump would start making noise. I installed a fuel cooler on that return line and never heard the pump noise again.
-
Senior Member
Originally Posted by
Bitsyncmaster
I did measure with two therm o-couples the fuel temp leaving the tank and fuel temp returned to the tank. It was about 1 deg.F warmer on the return temps. So I concluded that most of the fuel heating was due to the returned fuel. I did have the hot air dam on my car and the tank temps would easily get to 125 deg.F and then my fuel pump would start making noise. I installed a fuel cooler on that return line and never heard the pump noise again.
I remember seeing a picture of you cooler, what was the temperature after you installed it?
-
Senior Member
Originally Posted by
r00b
I remember seeing a picture of you cooler, what was the temperature after you installed it?
I never measured the temps after the install. You really need to to driving for the AC to work best (my AC accumulator cooled the return fuel). Since it cured my buzzing pump problem I was happy without further testing.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules