Replacing Fans and Fan Shroud

[JBaker4981]

I am wanting to replace my stock fans with the lower amperage fans from DI to limit how much of a beating the electrical system takes though the stock fans with Bitsyncmaster's Fan Relay and Fan Fail Unit have been amazing so far.

Is it possible to unbolt the existing fan shroud and drop it out without having to drain the system and take out the radiator? In my mind, it should be fairly easy but I have noticed a few people throughout various threads here that mentioned that dropping the fans was an utter nightmare.

I had hoped to find a How To Guide or any other thread specifically dedicated to this task on either DMCTalk or DMCToday however I came up short.

Thanks in advance for any advice!

[Bitsyncmaster]

I have dropped the shroud on two cars with the fans still installed. You have to drop the "sway" bar for the OEM fans to clear. Just have to have a good assortment of 1/4" drive sockets, extensions and wrenches. If the blots stick, work them back and forth carefully so as not to break any. So no need to drain cooling system or drop the radiator.

[WHO1DMC]

I am wanting to replace my stock fans with the lower amperage fans from DI to limit how much of a beating the electrical system takes though the stock fans with Bitsyncmaster's Fan Relay and Fan Fail Unit have been amazing so far.

Is it possible to unbolt the existing fan shroud and drop it out without having to drain the system and take out the radiator? In my mind, it should be fairly easy but I have noticed a few people throughout various threads here that mentioned that dropping the fans was an utter nightmare.

I had hoped to find a How To Guide or any other thread specifically dedicated to this task on either DMCTalk or DMCToday however I came up short.

Thanks in advance for any advice!

The only advice I have is get a strong friend to help push and pull on the radiator to try to find the little room there is to get those big fan motors out.. Now the fans won't drop straight out there will be a fight!

Doing this without taking the radiator out or totally removing the anti sway bar is a big PITA but I did it all by myself it took all day.


Dave B.

[Lenny]

I’m interested in doing the same thing. Living in Florida my fans are on most of the time.


Sent from my iPhone using Tapatalk

[bfloyd]

It's a pain to do it without dropping the radiator, but it can be done. I did it earlier this spring when I upgraded my fans and shroud. However, I ended up developing a hairline crack in my 2015 DMCH replacement radiator, so I ended up having to drop and drain the radiator anyway.

If you're wanting to just replace your fans with new low current models, DMCH sells new units that will bolt up directly to your existing shroud. If you're dead set on replacing the shroud "just because"... I would highly steer you toward Josh Bengston's set at Delorean Industries.

[JBaker4981]

It's a pain to do it without dropping the radiator, but it can be done. I did it earlier this spring when I upgraded my fans and shroud. However, I ended up developing a hairline crack in my 2015 DMCH replacement radiator, so I ended up having to drop and drain the radiator anyway.

If you're wanting to just replace your fans with new low current models, DMCH sells new units that will bolt up directly to your existing shroud. If you're dead set on replacing the shroud "just because"... I would highly steer you toward Josh Bengston's set at Delorean Industries.

I just purchased Josh's fans from DI and should have them by this weekend. Hopefully this won't be too difficult... I know the previous owner (tommyrich) originally had swapped the fans out and then back to stock at one time so I don't expect any issues out of the bolts. I'll have to figure out how to remove the sway bar and go from there.

[David T]

If you still have the OEM radiator with the plastic tanks, just replace the radiator too. Those little bolts and nuts are a real PITA and if they have not been touched in a LONG time expect to snap many of them off. Since you say things were recently worked on, you may be fortunate and will be able to remove them easily. Draining the radiator and refilling the system, IMHO, is easier than disconnecting the sway bar and trying to get the parts out in the limited space.

[Gregadeth]

Does anyone know how much the stock shroud/fans weigh and how much the aftermarket (stainless) ones weigh in comparison?