FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Results 1 to 8 of 8

Thread: Warm up regulator (pressure regulator )

  1. #1
    Junior Member
    Join Date:  Jan 2019

    Location:  Ponchatoula, LA

    Posts:    4

    My VIN:    SCEDT26T8BD004207

    Warm up regulator (pressure regulator )

    My WUR ground wire connection is not grounded. The black ground wire has continuity to the blue connector in the ignition coil box. The bulked head connection is not grounded. Does anyone know where this connection is grounded?

  2. #2
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    5,387

    Club(s):   (SEDOC) (DCUK)

    Is it blue with a black stripe (B/U)?

  3. #3
    Junior Member
    Join Date:  Jan 2019

    Location:  Ponchatoula, LA

    Posts:    4

    My VIN:    SCEDT26T8BD004207

    Wur

    No it is a solid black wire.

  4. #4
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    7,868

    My VIN:    03572

    The engine harness has splices in it combining some grounds and a few other circuits are also spliced. Check if the WUR ground goes to ground wire which goes to the engine block.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  5. #5
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    5,387

    Club(s):   (SEDOC) (DCUK)

    Quote Originally Posted by hjhjr View Post
    No it is a solid black wire.
    WUR Ground.jpg

  6. #6
    Junior Member
    Join Date:  Jan 2019

    Location:  Ponchatoula, LA

    Posts:    4

    My VIN:    SCEDT26T8BD004207

    WUR ground

    pin 22or 23 of the blue connector are not connected to ground. where do they connect to ground? I cannot tell by the ground diagram.

  7. #7
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    7,868

    My VIN:    03572

    Quote Originally Posted by hjhjr View Post
    pin 22or 23 of the blue connector are not connected to ground. where do they connect to ground? I cannot tell by the ground diagram.
    The bulkhead side connects as follows.
    22 To Lambda ECU pin 5
    23 To Lambda ECU pin 16

    The engine harness side ties those mating pins together and to the ground lug for the engine cylinder head. I think other grounds are also tied to the lug circuit.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  8. #8
    Junior Member
    Join Date:  Jan 2019

    Location:  Ponchatoula, LA

    Posts:    4

    My VIN:    SCEDT26T8BD004207

    I just checked with a trace light. The warm up regulator ground is the ground pin on the regulator. In other words pin 23 from the regulator grounds the Lambda ECU pin 16 through the regulator.. I also checked with trace light. I have no ground on ECU pin 5. There is no connection between ECU pins 5 or 16 to the case ground.
    The wiring diagram shows pin 12 connected to the case it is not and pin does not connect to anything in the ECU. Pins 22 & 23 are not connected to each other in my car. where is pin 5 of the ECU grounded?

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •