FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Results 1 to 7 of 7

Thread: Wiper control module

  1. #1
    Member cis6409's Avatar
    Join Date:  Jul 2011

    Location:  ireland

    Posts:    91

    My VIN:    6409

    Club(s):   (DOC-UK) (DOI)

    Wiper control module

    Hi guys
    Just trying to tidy up my wiring routing for under the steering column and inertia switch etc.

    At the moment it's just cable tied to the lambda counter loom and it's all just hanging.

    Can't seem to find where the wiper control/logic box bracket is supposed to be mounted.

    There does not seem an obvious place to locate it.
    Have checked the manual but the pic is vague just says attached to underside of dash on driver side.. but where?

    There is 3 speed clips attached but again can't see where they might go.

    Does anyone have a pic of it installed in the proper location or any other ideas?

    Many thanks
    Shane
    only from the past can we choose the correct path for the future...

  2. #2
    Senior Member
    Join Date:  Jun 2016

    Location:  Austin MN

    Posts:    342

    My VIN:    03500

    Quote Originally Posted by cis6409 View Post
    Hi guys
    Just trying to tidy up my wiring routing for under the steering column and inertia switch etc.

    At the moment it's just cable tied to the lambda counter loom and it's all just hanging.

    Can't seem to find where the wiper control/logic box bracket is supposed to be mounted.

    There does not seem an obvious place to locate it.
    Have checked the manual but the pic is vague just says attached to underside of dash on driver side.. but where?

    There is 3 speed clips attached but again can't see where they might go.

    Does anyone have a pic of it installed in the proper location or any other ideas?

    Many thanks
    Shane
    Hope this is a help to you.


    Dave B.
    Attached Images

  3. #3
    Senior Member Rich's Avatar
    Join Date:  May 2011

    Location:  San Francisco Bay Area, Calif.

    Posts:    1,835

    My VIN:    0934

    Club(s):   (NCDMC) (DCUK)

    And this.

    Item 3, wiper module, is shown as it is in that photo screwed to left side of Item 1, Plate Support.
    March '81, 5-speed, black interior

  4. #4
    Member cis6409's Avatar
    Join Date:  Jul 2011

    Location:  ireland

    Posts:    91

    My VIN:    6409

    Club(s):   (DOC-UK) (DOI)

    Thanks guys that's great!

    Cheers
    Shane
    only from the past can we choose the correct path for the future...

  5. #5
    Member cis6409's Avatar
    Join Date:  Jul 2011

    Location:  ireland

    Posts:    91

    My VIN:    6409

    Club(s):   (DOC-UK) (DOI)

    I've got the plate refitted
    Great to finally have it in the correct place and not hanging down..
    One other question the flasher relay is supposed to be attached to that aswell but instead of the relay mounted to the bracket the 3 pin electrical connector is fixed to the bracket and the relay is pushed on and off instead of the connector.

    All that's there is a small pozi drive black screw. Is there a way of securing the connector to the bracket?. I've seen it another pic on the net but it's not clear can't make out how it's done?

    Thanks
    Shane
    only from the past can we choose the correct path for the future...

  6. #6
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    5,889

    Club(s):   (SEDOC) (DCUK)

    The screw goes through the socket, and it holds the flasher unit. See Rich's link (#3) above.

  7. #7
    Member cis6409's Avatar
    Join Date:  Jul 2011

    Location:  ireland

    Posts:    91

    My VIN:    6409

    Club(s):   (DOC-UK) (DOI)

    O I see now, excellent thanks!


    Shane
    only from the past can we choose the correct path for the future...

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •