Bob,
This might be helpful: Attachment 22958 I have not used it and credit all goes to the author but it looks well written with pictures. Good luck.
Jeff
Bob,
This might be helpful: Attachment 22958 I have not used it and credit all goes to the author but it looks well written with pictures. Good luck.
Jeff
Put the door strut onto the new bracket. The doors now look like they open the same amount on both sides. The passenger side always looked lower than the drivers side. Both my doors do not open fully at 55 degree F today but do stay fully open if I help them. I also may play with those top seals. The seals do bind (I think they are too wide on the rubber). My drivers side also lifts the T-panel.
Dave M vin 03572
http://dm-eng.weebly.com/
Location: UK
Posts: 260
My VIN: #15768 EX #4584
Club(s): (DOC-UK)
Just received mine today, the list of winter jobs is getting longer....! (PX side also)Installed the passenger side door gas strut bracket. This is the bracket from Heninger so it installs without removing the 1/4 panel. I bought both sides but wondering why the drivers side does not get bent like the passenger side. Every car I've seen has the passenger side that needs a new bracket.
Chris
Chris Williams #15768 Back on the road after 14 years. Ex#4584
Worldwide DeLorean Owners Club: www.deloreans.co.uk Full colour DeLorean magazine shipped worldwide.
DeLorean Essential Buyers Guide: http://deloreans.co.uk/product/delor...-buyers-guide/
Here are some before and after shots:
Before:
20131109_143210.jpg
After:
20131109_150001.jpg
Done!
20131109_150039.jpg
As my car is with Eddie, we (Jessica, the owner, and myself) helped VIN 10480 do this for the first time since 2008:
DMCTalk.org Moderator
Actual snippet of a conversation from Sept 2013:
Me: Eddie, I can't wait to get the car back when you're done with it.
Eddie: Yeah, you'll be able to give the car gas, and it won't be - like - embarrassing....
Location: Illinois
Posts: 2,440
My VIN: 11408
Club(s): (DMWC) (TXDMC) (DCUK) (DOI)
sounds pretty rough
Supercharged 5.3L LS4 + Porsche 6spd
[email protected]
lsdelorean.com
I am not affiliated with Delorean Midwest in anyway.
Don't worry, it'll run great once Eddie is done with it. As he told me: "Jeremiah, just get it to where it can be started and driven on a transport. That's all I need."
He'll be doing a full on EFI conversion on it. For not being started in 4-5 years, I think it's pretty good . That video was taken just as the engine was able to idle on its own power.
The look on the owner's face when she saw her baby start up again was worth all 6.5 hours to me .
Last edited by DeLorean03; 11-10-2013 at 08:40 PM.
DMCTalk.org Moderator
Actual snippet of a conversation from Sept 2013:
Me: Eddie, I can't wait to get the car back when you're done with it.
Eddie: Yeah, you'll be able to give the car gas, and it won't be - like - embarrassing....
Location: Sunfield, Michigan, USA
Posts: 2,444
My VIN: 1798
Single-but-attached, and I-ain't-tellin'
I started a new thread for restoration and mod of Vin# 10480 here http://dmctalk.org/showthread.php?85...n-of-Vin-10480 so ya'll stop by, visit, and follow the fun!
Location: Sunfield, Michigan, USA
Posts: 2,444
My VIN: 1798