I have two springs that came with my car. I am just trying to identify if they are stock or aftermarket springs. Does anyone have the height of the stock front and rear springs?
Thanks!
Location: Illinois
Posts: 2,440
My VIN: 11408
Club(s): (DMWC) (TXDMC) (DCUK) (DOI)
I have two springs that came with my car. I am just trying to identify if they are stock or aftermarket springs. Does anyone have the height of the stock front and rear springs?
Thanks!
Supercharged 5.3L LS4 + Porsche 6spd
[email protected]
lsdelorean.com
I am not affiliated with Delorean Midwest in anyway.
Location: Illinois
Posts: 2,440
My VIN: 11408
Club(s): (DMWC) (TXDMC) (DCUK) (DOI)
Well I measured them to be 14-3/8" . Look like they are stock fronts? Or perhaps lowered rears?
Supercharged 5.3L LS4 + Porsche 6spd
[email protected]
lsdelorean.com
I am not affiliated with Delorean Midwest in anyway.
Probably more important to know the "wire" diameter than the no load length.
Dave M vin 03572
http://dm-eng.weebly.com/
Location: Illinois
Posts: 2,440
My VIN: 11408
Club(s): (DMWC) (TXDMC) (DCUK) (DOI)
I understand there is more to a spring than the length; the unloaded height could be the same as stock but the loaded could be less depending on the capacities and rate of the spring. Ill put a caliper on the coil later
Supercharged 5.3L LS4 + Porsche 6spd
[email protected]
lsdelorean.com
I am not affiliated with Delorean Midwest in anyway.
Location: San Francisco Bay Area, Calif.
Posts: 2,079
My VIN: 0934
Club(s): (NCDMC) (DCUK)
These readings are within 1/4 in tolerance in hopes of ID'ing yours.
Good point from Dave M about the wire diameters, so here you go.
Spring wire diameters for the pairs of OEMs we took off the car.
Front: 0.485 in.
Rear: 0.510 in.
With OEM coating, no corrosion. Used dial calipers.
Last edited by Rich; 04-28-2013 at 08:53 PM.
Location: Illinois
Posts: 2,440
My VIN: 11408
Club(s): (DMWC) (TXDMC) (DCUK) (DOI)
Thanks for taking the time to measure Rich!
Supercharged 5.3L LS4 + Porsche 6spd
[email protected]
lsdelorean.com
I am not affiliated with Delorean Midwest in anyway.
I got close to the same measurements, using vernier calipers. Also, they have some rust, so measurements will vary from others.
Front -
Length: 14.375
Outside Diameter: 4.475
Inside Diameter: 3.500
Wire Diameter: 0.490
Gap: 1.305
Turns: (about) 8.25
Rear -
Length: 16.375
Outside Diameter: 4.515
Inside Diameter: 3.480
Wire Diameter: 0.514
Gap: 1.185
Turns: (about) 9.9
I do not have a way of measuring the compression weight (or know the correct term for it). Hope that helps.
Location: Orlando, Florida
Posts: 2,734
My VIN: 01643
Club(s): (DCF) (DCO) (DCUK)
All DeLorean springs have a spring rate of 150lb/in (+/- ~3lbs)
If you're trying to identify OEM springs as was mentioned above the rears have a heavier wire size. Also as the pic below shows the rears will have a yellow paint smear and the fronts will have a red smear.
002.jpg
Jack Skeens