View Full Version : 2126 died---no start???
leroylem
07-24-2014, 06:42 PM
Car has been running great since I resurrected it 3 years ago--no problems. Filled up with gas where I always go Monday AM---drove about 20 miles after, no problems, next afternoon headed to town---started hard miss in high gear when accelerating---progressively got worse---headed back home---didn't make it---finally died---had to be towed home---here is what we've done to try to fix---pump is running--removed the fuel hose at the cold start valve---spun it over---getting plenty of fuel---did the plug swap--checked fire at the plugs---good strong spark---sprayed starting fuel down the throat---still no start----pulled one injector---jumped RPM relay(Daves)---sprayed plenty in a bottle----checked timing with lite ----appears to be correct. The only thing left to me is the gas, but we have pumped out a little---it looks good, smells OK, I also talked to the station manager---they have had no complaints about bad gas. I hate to pump out the tank at this point----maybe someone could tell us what we have missed. I Just don't know what else to look at.
Thanks for any ideas.
Jonathan
07-24-2014, 06:54 PM
Fuel = ok
Spark = ok
Air = ?
Any reason to think you have something blocking air flow? Maybe have a quick look into the air filter housing or ducts. Or take it off and try the car without it for a moment.
NightFlyer
07-24-2014, 06:57 PM
Vacuum leak.
Do a thorough check.
A few owners have recently had troubles caused by a problem with the air induction system. Specifically, the rubber flex joint/gasket that connects the lower mixture unit housing to the throttle body, No. 11 in the image below, Part No. 102772 (which is NLA), cracks/splits causing a HUGE unmetered air/vacuum leak. This causes the engine to run extremely lean, and depending upon how bad of a leak is present, can stall out a running engine or even prevent the engine from starting. Being a flexible joint, it's possible to be fine at idle, but just the slight shift in engine orientation that occurs when going open throttle/under load can be enough to pull the crack/tear/split open, thus resulting in an engine that feels powerless and/or stalls out. As a replacement part is NLA, your only options, should you encounter such a problem, are to find one on a junk yard Volvo PRV or do your best in repairing the existing one.
http://store.delorean.com/images/Category/large/1-4-1.gif
Bitsyncmaster
07-24-2014, 07:51 PM
Did it even fire at all when you used the "plug swap" or starting fluid?
leroylem
07-24-2014, 08:05 PM
Did it even fire at all when you used the "plug swap" or starting fluid?
It has never even "popped"---absolutely nothing---even pulled a couple plugs--squirted gas directly into cylinders---still nothing---good hot battery, with charger boost---spins fast---an earlier reply mentioned a massive air/vac leak at the lower fuel metering unit??? Also, checked compression---it is good??? any ideas???
NightFlyer
07-24-2014, 08:07 PM
Did it even fire at all when you used the "plug swap" or starting fluid?
I was also going to suggest a faulty relay, but then I saw that he was running yours.
Have you had any failures of your solid state modules that you're aware of?
Bitsyncmaster
07-24-2014, 08:34 PM
It has never even "popped"---absolutely nothing---even pulled a couple plugs--squirted gas directly into cylinders---still nothing---good hot battery, with charger boost---spins fast---an earlier reply mentioned a massive air/vac leak at the lower fuel metering unit??? Also, checked compression---it is good??? any ideas???
I was going to suggest a compression check but you beat me to it. All I can think of is your "good spark" test is not valid.
Bitsyncmaster
07-24-2014, 08:37 PM
I was also going to suggest a faulty relay, but then I saw that he was running yours.
Have you had any failures of your solid state modules that you're aware of?
It's been years since any failures and those two were because the connector was plugged in backwards. If I were to ever make my own connector, I would make the guide a solid ring around the pins.
NightFlyer
07-24-2014, 08:43 PM
If spark is good, then it's gotta be a massive air/vacuum leak.
The problem that I previously described has been known to be severe enough to prevent start-ups.
leroylem
07-24-2014, 09:47 PM
If spark is good, then it's gotta be a massive air/vacuum leak.
The problem that I previously described has been known to be severe enough to prevent start-ups.
I just went to the shop and attempted to inspect the rubber flex gasket you mentioned----of course, difficult to see, but with a good inspection mirrow & lite, I can see most of seal area--not all---could not see any definite cracks, tears----any way to test this without tearing everything apart??
NightFlyer
07-24-2014, 11:04 PM
I just went to the shop and attempted to inspect the rubber flex gasket you mentioned----of course, difficult to see, but with a good inspection mirrow & lite, I can see most of seal area--not all---could not see any definite cracks, tears----any way to test this without tearing everything apart??
Smoke machine. Other than that, the only test I know of only works if the car is actually running/idling.
If the joint looks OK, then let's assume that it's good. That brings us back to either fuel pressure or ignition. As it's usually always fuel instead of ignition, let's start with fuel.
There may be a problem with the CPR/WUR. You'll need the Bosch K-Jet gauges though to properly diagnose this.
Best luck :thumbup:
I just went to the shop and attempted to inspect the rubber flex gasket you mentioned----of course, difficult to see, but with a good inspection mirrow & lite, I can see most of seal area--not all---could not see any definite cracks, tears----any way to test this without tearing everything apart??
Three things:
1. Vacuum leak test
One way to figure out whether there is a massive vacuum leak without smoke or a teardown is to use a vacuum gauge plumbed in anyplace past the throttle while cranking (with throttle closed).
Charge up the battery before testing to be sure she spins over nice and fast, sort of like a simulated idle condition. No idea what the reading should be but it should register something. You can also run the test with throttle half open or full open (a no-vacuum condition) and compare.
Feel free to disable the fuel pump for this test since you don't expect the engine to start anyway. The inertia switch makes that easy to do.
2. Spark really OK?
I guess I don't quite understand why a vacuum leak would keep it from at least catching and maybe sputtering on starting fluid if the spark is really OK. The "factory book" test: Pull the ignition cable off of the center of the distributor and hold the end of it 0.5 in. from a good ground while cranking and look for a spark across that (large) gap. If you have to reduce the gap below 0.5in. to get any spark then you may have an ignition problem.
3. Exhaust problem?
This might sound weird - have you had any trouble with your catalytic converter? If it were to fail massively, as in kind packing it in as the engine progressively ran more poorly during your last drive then you might now have a big plug in the exhaust keeping air from getting out of the engine - and it thus cannot get in. With throttle wide open, the FP turned off and one of the exhaust pipes plugged check for good airflow out of the other exhaust pipe while cranking fast. While you're at it see if the air metering plate is moving down.
These tests can all be done in 10-15 minutes. After you find a vac gauge.
leroylem
07-25-2014, 12:07 AM
Three things:
1. Vacuum leak test
One way to figure out whether there is a massive vacuum leak without smoke or a teardown is to use a vacuum gauge plumbed in anyplace past the throttle while cranking (with throttle closed).
Charge up the battery before testing to be sure she spins over nice and fast, sort of like a simulated idle condition. No idea what the reading should be but it should register something. You can also run the test with throttle half open or full open (a no-vacuum condition) and compare.
Feel free to disable the fuel pump for this test since you don't expect the engine to start anyway. The inertia switch makes that easy to do.
2. Spark really OK?
I guess I don't quite understand why a vacuum leak would keep it from at least catching and maybe sputtering on starting fluid if the spark is really OK. The "factory book" test: Pull the ignition cable off of the center of the distributor and hold the end of it 0.5 in. from a good ground while cranking and look for a spark across that (large) gap. If you have to reduce the gap below 0.5in. to get any spark then you may have an ignition problem.
3. Exhaust problem?
This might sound weird - have you had any trouble with your catalytic converter? If it were to fail massively, as in kind packing it in as the engine progressively ran more poorly during your last drive then you might now have a big plug in the exhaust keeping air from getting out of the engine - and it thus cannot get in. With throttle wide open, the FP turned off and one of the exhaust pipes plugged check for good airflow out of the other exhaust pipe while cranking fast. While you're at it see if the air metering plate is moving down.
These tests can all be done in 10-15 minutes. After you find a vac gauge.
Thanks Rich---I also think it should at least sputter or pop---something---spark is very good at coil and at plugs---I will check the vac and the plugged exhaust tomorrow.
Thanks Rich---I also think it should at least sputter or pop---something---spark is very good at coil and at plugs---I will check the vac and the plugged exhaust tomorrow.
OK, I want to believe you have very good spark but will ask this anyway - are you saying that the coil cable will generate a spark to ground at a gap of 0.5in.?
Seeing a spark at some random (closer) distance at the end of that cable end or seeing the spark plug fire is not the same thing as that test is.
I can ask it a different way.....What is the largest gap over which you see a consistent series of ignition sparks to ground off of the end of the coil cable during cold cranking with a topped up battery? Data.
And do remember to turn the FP off for the tests. Lots of gas will flood it. And it won't help your engine oil, either. And remember to turn the FP back on when you need it....have fun with it tomorrow.
leroylem
07-27-2014, 08:15 PM
Three things:
1. Vacuum leak test
One way to figure out whether there is a massive vacuum leak without smoke or a teardown is to use a vacuum gauge plumbed in anyplace past the throttle while cranking (with throttle closed).
Charge up the battery before testing to be sure she spins over nice and fast, sort of like a simulated idle condition. No idea what the reading should be but it should register something. You can also run the test with throttle half open or full open (a no-vacuum condition) and compare.
Feel free to disable the fuel pump for this test since you don't expect the engine to start anyway. The inertia switch makes that easy to do.
2. Spark really OK?
I guess I don't quite understand why a vacuum leak would keep it from at least catching and maybe sputtering on starting fluid if the spark is really OK. The "factory book" test: Pull the ignition cable off of the center of the distributor and hold the end of it 0.5 in. from a good ground while cranking and look for a spark across that (large) gap. If you have to reduce the gap below 0.5in. to get any spark then you may have an ignition problem.
3. Exhaust problem?
This might sound weird - have you had any trouble with your catalytic converter? If it were to fail massively, as in kind packing it in as the engine progressively ran more poorly during your last drive then you might now have a big plug in the exhaust keeping air from getting out of the engine - and it thus cannot get in. With throttle wide open, the FP turned off and one of the exhaust pipes plugged check for good airflow out of the other exhaust pipe while cranking fast. While you're at it see if the air metering plate is moving down.
These tests can all be done in 10-15 minutes. After you find a vac gauge.
Thanks to all who have offered possible problems/solutions---2126 still will not start---however, we finally decided to pull it and it did actually start and ran about 5 second---died, has not hit or sputtered since. Even now got a new battery, and with a hot charge, will jump a half inch spark from the coil----cold start valve disconnected, and rpm relay unplugged, sprayed starting fluid into the intake---still will not even pop. I wonder now about a plugged cat/exhaust. How much air flow/pressure should you feel at the exhaust tips at cranking speed???I covered the tips with masking tape----cranking speed will not disturb the tape----could this be the problem??comments welcome .
....How much air flow/pressure should you feel at the exhaust tips at cranking speed???I covered the tips with masking tape----cranking speed will not disturb the tape----could this be the problem??comments welcome .
Yes. Could be.
PM sent.
bayouboy
12-18-2014, 01:09 PM
Sorry to see this topic terminate in the middle of the problem. That was 5 months ago. What turned out to be the solution?
Sorry to see this topic terminate in the middle of the problem. That was 5 months ago. What turned out to be the solution?
Tracking back on Leroy's last no-start thread post to his other posts shows at least one story of the resolution. See his Post #4500, relating the success story to someone else with a non-start situation about 3 wks ago:
http://dmctalk.org/showthread.php?241-What-have-you-done-to-your-DeLorean-today&p=161699#post161699
Weak spark.
leroylem
12-18-2014, 11:32 PM
Sorry ---guess I failed to update my problem/resolution on the Talk site---AFTER AT LENGTH TESTING, TALKING, CUSSING/DISCUSSING, I FINALLY DECIDED MY PROBLEM HAD TO BE A WEAK SPARK---I HAD SPARK AT THE PLUGS, BUT NOT ENOUGH TO START. I HAD REPLACED THE BATTERY---HAD A 50a BOOST CHARGER CONNECTED WHILE TRYING TO START---STILL NO START---, DECIDED TROUBLE HAD TO BE IN THE DISTRIBUTOR---STRIPPED IT DOWN TO THE vod---REPLACED DIST CAP, ROTOR, WIRES AND PLUGS--DECIDED THIS WOULD BE A GOOD TIME TO SEE IF I COULD FAB AN INTAKE MANIFOLD IN MY SHOP---BUILT THE INTAKE MANIFOLD IN MY SHOP, INSTALLED A REBUILT CARB, PLUGGED THE INJECTOR HOLES, AND MADE A BRACKET TO UTILIZE THE THROTTLE SPOOL---STARTED FIRST CRANK---RUNS SO GOOD I HAVE NOT YET RE-INSTALLED K-JET. THE PROBLEM WAS ELECTRICAL---K-JET HAD BEEN RUNNING FINE---IT WON'T BE MUCH TROUBLE TO GO BACK WHEN I HAVE TIME.
THANKS AGAIN TO ALL WHO RESPONDED TO MY REQUEST FOR ADVICE/OPINIONS.
Andrew
12-18-2014, 11:38 PM
Congrats on getting it going!
Just for the sake of information, what type of carb are you running? Also did you do a complete custom intake or did you modify a stock intake. Finally what fuel pump are you running with your carb?
Andrew
4194
5052
Sent from my LGL55C using Tapatalk 2
leroylem
12-19-2014, 09:12 AM
[QUOTE=Andrew;163302]Congrats on getting it going!
Just for the sake of information, what type of carb are you running? Also did you do a complete custom intake or did you modify a stock intake. Finally what fuel pump are you running with your carb?
Andrew
4194
5052
I built the manifold entirely---made flanges from 1/2 inch plate---runners are 1 1/2 j bend tubing--made a plenum from 1/4 inch plate--all mig welded---carb is 2100 Ford/w electric choke--mounted an airtex pump near the tank, & fabbed a pickup system in the tank--ran a new fuel line back to the engine. WORKED OUT REALLY GOOD---RUNS WELL---POWER/ECONOMY SEEM ABOUT SAME AS K-JET.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.