View Full Version : General A/C Won't Flush.
WHO1DMC
08-07-2016, 02:37 PM
Can't get a/c to flush. Put some flush in low side applied air in low side and nothing nothing nothing! Every thing looks to be original. I have seen you tube video that this works pretty well.
Any thoughts? :banghead:
Bitsyncmaster
08-07-2016, 03:58 PM
Can't get a/c to flush. Put some flush in low side applied air in low side and nothing nothing nothing! Every thing looks to be original. I have seen you tube video that this works pretty well.
Any thoughts? :banghead:
What hose are you flushing from. You have to remove the hose going to the evaporator and then flush the condenser from the high pressure hose at the compressor. Then you can flush the evaporator if you pull the orifice and accumulator but most of the required flush is the condenser.
WHO1DMC
08-07-2016, 04:23 PM
Well I pulled a failed compressor. It would turn part way than dead stop. Took the back of for new compressor some pressure was released than I could turn it all the way round. It was also deprived of oil not a drop. I found a you tube video were 2 guys flushing a system in from the low out the high side going through the entire thing and on a Delorean. Well if I mest up did I do a lot of damage? I think I'm in for a good ride.
Putting in a SD5h14.
Thanks Dave B.
DMCMW Dave
08-07-2016, 04:43 PM
Well I pulled a failed compressor. It would turn part way than dead stop. Took the back of for new compressor some pressure was released than I could turn it all the way round. It was also deprived of oil not a drop. I found a you tube video were 2 guys flushing a system in from the low out the high side going through the entire thing and on a Delorean. Well if I mest up did I do a lot of damage? I think I'm in for a good ride.
Putting in a SD5h14.
Thanks Dave B.
You really need to pull the orifice tube to get a good flush. Also if you flush though the accumulator you just end up with an accumulator full of flushing oil and old compressor parts.
WHO1DMC
08-07-2016, 04:59 PM
Sorry for the lack of Knowledge but is there some step by step were to disconnect from and blow through? I do know of the orifice tube can be a B.
Thanks Dave B.
Bitsyncmaster
08-07-2016, 05:11 PM
A few guys flush with the accumulator but as Dave S said, that just fills up the accumulator with old oil and you really can't get the flush out of it. The orifice tube will really limit the flow of the flush and the screen on the orifice will just plug up with the junk you want to flush.
content22207_2
08-07-2016, 05:23 PM
Actually the screen will get cleared out if you flush backwards (all the crap was trapped flowing forward).
I suspect Steve Rice and I and the two YouTube guys referenced, flushing Brandon Barber's A/C out. Worked pretty good, eh? A/C was still working when he sold the car.
Rich Rogers and I repeated the procedure at Justin Mettee's house. Worked pretty good then too. Rich's A/C was still working when he sold that car.
I guess the only drawback of flushing the system backwards is it appears to lead to sale of the car (albeit with the A/C still working).
Bill Robertson
#5939
spikeygg
08-07-2016, 05:51 PM
Don't want to hijack this thread but I have a related question.
I was thinking about pulling the accumulator and orifice tubes from my system and flush the two halves independently -- is that a bad idea? I was planning on flushing both of them in reverse to maximize the effect.
content22207_2
08-07-2016, 06:07 PM
Farrar didn't think so.
Then he accidentally damaged tubing going into the evaporator trying to separate them....
(Helpful hint: if you damage the evaporator you have to take the whole dashboard apart to replace it).
The world is full of people telling you to disassemble the system to flush it.
Curiously, none of those people will come to your house to help you put a new evaporator in after it gets damaged.
Bill Robertson
#5939
spikeygg
08-07-2016, 06:41 PM
Farrar didn't think so.
Then he accidentally damaged tubing going into the evaporator trying to separate them....
(Helpful hint: if you damage the evaporator you have to take the whole dashboard apart to replace it).
The world is full of people telling you to disassemble the system to flush it.
Curiously, none of those people will come to your house to help you put a new evaporator in after it gets damaged.
Bill Robertson
#5939
Actually, I just vacuumed out my A/C system this morning and to my surprise it's holding ~25mmHG of vacuum. So I might try it your way to begin with. Let me know if I have these rough steps correct:
Disconnect the compressor and pull it from the engine bay
Flush the entire system backwards as-is
Blow out the entire system with the air compressor
Drain and refill the compressor with the mineral oil (replace O-rings)
Reinstall the compressor
Vacuum out the system
Recharge the system with R134a
I've been studying this post (http://www.dmctoday.com/showthread.php?927-Convert-Your-A-C-System-to-Use-an-Alternative-Refrigerant).
content22207_2
08-07-2016, 06:48 PM
Drain and refill the compressor with the mineral oil (replace O-rings)
I'd use Ester. It's the universal refrigerant oil.
Bill Robertson
#5939
spikeygg
08-07-2016, 06:51 PM
I'd use Ester. It's the universal refrigerant oil.
Bill Robertson
#5939
Sorry that's what I meant, Ester oil, but is that the only correction? :)
content22207_2
08-07-2016, 06:53 PM
My Autozone loans vacuum pumps, but found out at Brandon's house his Autozone doesn't (none of the parts houses around there do). At the time I didn't own a vacuum pump of my own (just borrowed one from Autozone whenever needed), so we used engine vacuum instead. It works, but a proper vacuum pump is optimal. Vacuum pumps don't cost very much, so you may as well buy one if you can't find a loaner.
Bill Robertson
#5939
Bitsyncmaster
08-07-2016, 08:37 PM
Don't want to hijack this thread but I have a related question.
I was thinking about pulling the accumulator and orifice tubes from my system and flush the two halves independently -- is that a bad idea? I was planning on flushing both of them in reverse to maximize the effect.
That is how I do it. If your careful and use two wrenches, you don't damage the evaporator removing the accumulator. I had installed a VOV valve to replace the orifice and it did not work because the tube had a bend in it. It also got stuck when I went to remove it. I pressurized at the compressor and plugged the open hoses and it blew that VOV valve out like a bullet.
WHO1DMC
08-08-2016, 03:38 AM
Sounds like a plan I'll start at the evaporator and remove orifice tube and accumulator . The nuts on the accumulator are the one's that move correct?
Dave B.
Bitsyncmaster
08-08-2016, 06:47 AM
Sounds like a plan I'll start at the evaporator and remove orifice tube and accumulator . The nuts on the accumulator are the one's that move correct?
Dave B.
Good question. I guess I never really thought about that before since I can usually see what should move. I just looked at a spare accumulator I have and there are no movable nuts on it. That is the new type accumulator. Some of the older Ds used another type that had a hose connection on the bottom.
bfloyd
08-08-2016, 02:08 PM
Sounds like a plan I'll start at the evaporator and remove orifice tube and accumulator . The nuts on the accumulator are the one's that move correct?
NO... The nut on the accumulator is fixed and welded on. The part of the fitting that moves on those pipes are on the evaporator tubes. I repeatedly soaked mine in PB Blaster for almost two weeks before I took a shot at it with wrenches the other night. Had my oldest son lay under the wheel well and hold on to the accumulator while I crawled up in the trunk and loosened the fittings on the evaporator tubes. Came right off with hardly no struggle at all. Once the accumulator was out, removing the line and fitting to the orifice tube was super easy.
As soon as Josh (DPI) gets me the instructions on how to assemble these new fittings, I'll be back up and running with air conditioning.
Farrar
08-08-2016, 07:27 PM
If [you're] careful and use two wrenches, you don't damage the evaporator removing the accumulator.
And here's hoping the previous owner didn't install any "stop leak" which essentially corrosion-welds the connection. All that wrenching on mine caused a breach in the tube. I ripped the damn thing out with half of the short hose still on it. :angry::angry::angry::angry::angry:
DMCMW Dave
08-08-2016, 08:02 PM
And here's hoping the previous owner didn't install any "stop leak" which essentially corrosion-welds the connection. All that wrenching on mine caused a breach in the tube. I ripped the damn thing out with half of the short hose still on it. :angry::angry::angry::angry::angry:
It doesn't take stop leak. A year of driving in a area of salted roads will do a fine job of welding the aluminum and steel pipes together.
content22207_2
08-08-2016, 08:13 PM
I would go so far to say merely driving in wet weather will eventually weld the aluminum and steel together (electrolysis/galvanic corrosion uses plain old H2O as the electrolyte).
Lotus may be geniuses, but putting the accumulator in the wheel well wasn't exactly the smartest thing they've ever done.
Bill Robertson
#5939
DMCMW Dave
08-08-2016, 08:57 PM
I would go so far to say merely driving in wet weather will eventually weld the aluminum and steel together (electrolysis/galvanic corrosion uses plain old H2O as the electrolyte).
Lotus may be geniuses, but putting the accumulator in the wheel well wasn't exactly the smartest thing they've ever done.
#5939
I've had a car or two in the shop where it was relocated into the trunk. A bit of intrusion on trunk space though.
WHO1DMC
08-09-2016, 10:57 AM
Accumulator off, evaporator side went good hose needed some effort. Now orifice tube, how do the fittings turn? Do they both turn or one and not the other?
Thanks for the help. Dave B.
Bitsyncmaster
08-09-2016, 11:55 AM
Accumulator off, evaporator side went good hose needed some effort. Now orifice tube, how do the fittings turn? Do they both turn or one and not the other?
Thanks for the help. Dave B.
I have a spare hose that goes from the condenser to evaporator (I needed the hose with the hub so got this by accident) and both those hose fittings rotate.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.