Log in

View Full Version : Transmission Auto Bad Torque Converter



brew
08-09-2016, 01:21 PM
Hey everybody, just got done replacing the auto trans in the D and it's having some issues. It slips when moving off in Drive and Reverse, which according to the workshop manual could be low fluid, fluid pressure, valve body, or torque converter. The fluid pressure and level check out normal, and I replaced the valve body with my known good one from my old trans. So that leaves the torque converter. The car itself is making an unusual noise that I can't even describe, but I can only assume it's the converter.

https://www.youtube.com/watch?v=TwEwDFqtBME
Here's a video of it in motion, if you can listen closely you can here that strange noise over the crazy amount of brake squeal lol. You can also hear the engine reving higher than needed to back up. I also have the new "digital" auto trans governor.

Jonathan
08-09-2016, 04:43 PM
Fuses look okay? Maybe you'll get lucky and it will be something that wasn't hooked back up right with the shift computer or wiring connections.

DMCMW Dave
08-09-2016, 06:31 PM
Fuses look okay? Maybe you'll get lucky and it will be something that wasn't hooked back up right with the shift computer or wiring connections.

Fuses/shift computer don't impact reverse and don't cause bad noises. I don't recognize this one.

David T
08-09-2016, 06:58 PM
Are you sure it is slipping? Can the brakes be dragging badly also causing the squeal? You said you "rebuilt" the trans. What did you do (if anything) to the torque convertor? Rare for them to go bad unless it is an especially high mileage part. Recheck your fluid level and pressure as per the Service Manual. If your levels and pressures are OK then it is the clutch packs.

brew
08-09-2016, 10:38 PM
I am 100% sure it's slipping. Other than the slipping when moving off in drive or reverse, everything shifts fine. Another thing to mention, the transmission only slips when there is a load on it, like when actually driving it. However if you jack the rear end up so the wheels are off the ground and put it in drive, the slipping goes away.

I didn't rebuild the trans, I bought a used one off a nice gentlemen from our forums. It had about 8k miles on it when removed but I have no idea how long it had been sitting before I got it. There could have been moisture that got in the converter and wreaked havoc or some other kind of disaster.

Lwanmtr
08-10-2016, 07:52 AM
To me it sounds like the noise increases with speed?

Jonathan
08-10-2016, 08:15 AM
How's the oil level/condition in the final drive? Have you checked or replaced that fluid recently?

David T
08-10-2016, 10:30 PM
Repeating, if you have the proper level of fluid and good line pressure, if it is slipping the clutch packs are gone. Last thing to try is running without a filter and see if that helps. If none of this works you must either replace the trans or get it rebuilt. The torque converter is not the problem.

brew
09-27-2016, 09:44 PM
Just wanted to give a final answer to this. It ended up being a bad torque converter. I took it out for a 2 hour shake down run and everything drives, shifts, and downshifts as it should.

David T
09-27-2016, 10:33 PM
Just wanted to give a final answer to this. It ended up being a bad torque converter. I took it out for a 2 hour shake down run and everything drives, shifts, and downshifts as it should.

Glad you found it. An unusual one. It would be interesting to open up the T/C and see what happened. Typically when you do transmission work you have the torque convertor rebuilt since it is impossible to clean it properly. Drive the car for a while and recheck all of the external On-Car adjustments and recheck your fluid levels. Make sure the wiring to the shift computer is securely away from the exhaust pipes.