Log in

View Full Version : Frame & Body Where to mount "Emblem clips" SP10557



BABIS
08-11-2016, 11:50 AM
Hello guys,

last time I removed my centre console I had these 2 clips falling from the console: http://www.delorean.eu/catalog/product_info.php?cPath=19_31_129&products_id=129052
(they are not even listed on DMCH site, part #39 here http://www.delorean.eu/catalog/index.php?cPath=19_31_129)
do you have a pic to see where they are mounted? I am guessing on the mounting bars, near the end towards the front of the car

Many thanks

Jonathan
08-11-2016, 11:58 AM
Look at the second photo in this post:

http://dmctalk.org/showthread.php?10336-Assorted-helpful-technical-photos&p=165448&viewfull=1#post165448

See towards the rear of the car, bottom end of where the shifter is, that little flat bracket/bar going across? Are those the two clips you mean?

I looked at the parts website and agree it doesn't make sense from what you see there. I can't tell from that picture on the EU website whether they have holes across the centre of them, but if they do, this is what came to mind when I read your description of where you were looking.

DMC-81
08-12-2016, 08:43 AM
Hi there,

If you look at Jonathan's picture, they go in the forward holes in the bracket that have the little rectangle in them. It's a clip that grabs the smooth post in the shifter panel that go in those holes. The clips go in with the pointed end down.

Hopefully that make sense.

Cheers,

BABIS
08-13-2016, 04:18 PM
Hello guys,
they definitely aren't the clips on the small bracket at the base of the shifter, I attached a couple of pics of the clips I am talking about (the same displayed on dmc.eu website and missing from houston):

4538045381

Ryan King
08-13-2016, 04:51 PM
Hi there,

If you look at Jonathan's picture, they go in the forward holes in the bracket that have the little rectangle in them. It's a clip that grabs the smooth post in the shifter panel that go in those holes. The clips go in with the pointed end down.

No. Its not those...I have my shifter plate apart right now and I just inspected mine as well. His clips aren't the same...

So weird, what are these!?!

Ryan King
08-13-2016, 04:53 PM
Hello guys,
they definitely aren't the clips on the small bracket at the base of the shifter, I attached a couple of pics of the clips I am talking about (the same displayed on dmc.eu website and missing from houston):

4538045381

I KNOW WHAT THEY ARE

They attach to the sides of the center console, and there are two brackets on either side that attach to the knee pads. There is a screw that goes through the hole on the clip and into the center console. Ill snap a photo for reference.

Ryan King
08-13-2016, 04:59 PM
45383

DMC-81
08-13-2016, 06:39 PM
Hi there,

If you look at Jonathan's picture, they go in the forward holes in the bracket that have the little rectangle in them. It's a clip that grabs the smooth post in the shifter panel that go in those holes. The clips go in with the pointed end down.

Hopefully that make sense.

Cheers,

Hi there,

I'm sorry. I guess a picture is worth a thousand words. :)

Here is what I meant...

Clip installed pointed end down in the rectangular hole...
45388

It grabs the smooth post....
45389

2 clips installed....
45390

You need to ensure that the thick wire harness that runs below the clip doesn't interfere during installation.

Ryan King
08-13-2016, 06:55 PM
Hi there,

I'm sorry. I guess a picture is worth a thousand words. :)

Here is what I meant...

Clip installed pointed end down in the rectangular hole...
45388

It grabs the smooth post....
45389

2 clips installed....
45390

You need to ensure that the thick wire harness that runs below the clip doesn't interfere during installation.

Oh wow! I have NEVER seen those before.

I want some now....

BABIS
08-14-2016, 09:32 AM
Hi there,

I'm sorry. I guess a picture is worth a thousand words. :)

Here is what I meant...

Clip installed pointed end down in the rectangular hole...
45388

It grabs the smooth post....
45389

2 clips installed....
45390

You need to ensure that the thick wire harness that runs below the clip doesn't interfere during installation.

BINGO!

thank you so much ;)

DMC5180
08-14-2016, 01:37 PM
Oh wow! I have NEVER seen those before.

I want some now....

NO you really don't.

They are a one way retainer. The forward pins go IN fine, if in proper alignment, but can be troublesome get back out IF you need the Cover removed again. Half the time the clips will fall out during the install process, mine did repeatedly on one side. They were really meant for a one and done installation. A Ball stud snap in fastener configuration would have been a better choice here (think battery cover or Grill attachment ). The console cover will stay in place just fine without them because the A/C panel sits over the front lip of the cover plate. If your going for factory purity like Dana, then put'em in, no harm in that. Besides when Dana gets done, the car will be so perfect nothing will ever go wrong in the future. Trailer QUEEN :biggrin:

DMC-81
08-14-2016, 07:58 PM
^ Thanks Dennis! I guess I'm somewhat of a perfectionist. The car is babied, but I intend to enjoy it when it's done.

I see that my clips do not have the brads that bite into the post like the EU part. That makes it grab the post, but easy to take off the shifter panel. Maybe there were production changes?

SpudMurphy
04-01-2020, 03:58 PM
^ Thanks Dennis! I guess I'm somewhat of a perfectionist. The car is babied, but I intend to enjoy it when it's done.

I see that my clips do not have the brads that bite into the post like the EU part. That makes it grab the post, but easy to take off the shifter panel. Maybe there were production changes?

I purchased the clip SP10557, as they are advertised as also being used as tread plate clips.
When I received the new clips they don't have the barb as shown in one of the earlier pictures in this thread. Without the barb they will not fit or should I say, "grip" the tread plate plastic lug
Here's a picture showing the old and new clips - the old clips have the tang formed by a hole punched (not drilled) into the clip.
63184
I've had to send the clips back for a refund as they won't "do" what the they should.

I've done quite a bit of work on my treadplates and plastic sills .... they are now solid as a rock and 100% better than the factory install.
I used 3 of these instead on the treadplate and bonded them using Wurth Bond after scouring the plastic to aid bonding.

6318563186

Those damn clips (sp10557) ... and I can confirm .... you don't need them on the console - so imo these clips are worthless so don't waste your money


On the first photo, you can see the "witness marks" on the treadplate platic legs - if you use the sp10557, they plastic legs will not grip and will just float about in SP10557 like a "prick in a shirt sleeve" .