PDA

View Full Version : General MASTER - parts cross reference list



hillbillysims
08-22-2016, 10:33 AM
I've been learning a lot in the 2 weeks I have been a member here & keep seeing lots of mentions about saving money by buying cross referenced parts.

Is there an existing "Master List" or thread of all parts that can be cross referenced? I didn't find one using search

If not, that could be a useful thing for all of us to start putting together.

Michael
08-22-2016, 10:44 AM
http://dmctoday.com/showthread.php?5-Cross-reference-parts-list

dn010
08-22-2016, 10:44 AM
http://dmctalk.org/showthread.php?932-Parts-Crossover-List

David T
08-22-2016, 12:08 PM
http://dmctalk.org/showthread.php?932-Parts-Crossover-List

It is getting harder and harder to even get the cross/ref parts. For the most part the cars that the cross/ref parts go on are also getting very old and no one is stocking them either. Also a lot of the companies that are cross/refed are no longer in business and the stock has been depleted. Another thing that is happening is parts are being cross/refed that don't fit right or work well. Buying from one of the Delorean vendors insures that what you buy will fit and work because they use the same parts in their service departments. Of course this doesn't apply to stuff like fuses and bulbs or hoses but for the more specific parts you are best served by using your favorite Delorean vendor. In many cases they are selling parts for less than you can get locally if you can even find it. If you need the part in a hurry they can often ship "Next Day" if you order the part early enough.

DMCVegas
08-22-2016, 01:02 PM
Cross-referenced parts were great back when we were running low on parts. Nowadays though it seems that rather than the DeLorean relying upon other cars for parts, other cars are now relying upon our parts supply.

I've also done the whole looking through parts catalogs for brake pads and trying to match silhouettes, and I can't say it was much fun. Especially when the pads squealed. I the end, I didn't really save that much cash either. Stick with a DeLorean vendor.

Josh
08-22-2016, 01:17 PM
If you are looking to save money buying cross referenced parts - you are sadly mistaken

The DMC vendor support is great, and prices are reasonable. Better than most cars in my experience.

You can waste alot of time and money hunting down cross referenced parts that may or may not work, then end up buying the dmc part anyway later. Way more expensive. I speak from experience.

content22207_2
08-22-2016, 02:03 PM
Not everything is cheaper from a vendor (O rings, for example -- even round ones), and some things vendors just don't sell, such as CV joints.

Some xRef'd items, such as the heater core shutoff valve, are arguably better designed than what the vendors sell (sealed diaphragm versus gate valve with external linkage).

Houston resells Borgeson steering columns, but they don't offer them with vibration reduction -- if you want that option you need to buy from Borgeson direct (which is about $100 cheaper...).

Refusing to xRef on principle alone can be more expensive in the long run, and you may find yourself without a needed part (I waited half a year for Houston to restock coolant temp sending units before buying a one off the shelf at Autozone).

That said, some things are the same price or cheaper from Houston. I xRef'd the water pump radiator hoses from Gates but only saved a couple of dollars. Houston's CV joint boots are basically the same price as outside sources.

Note that Houston does not offer lifetime warranties on things such as alternators and starter motors.

Bill Robertson
#5939

dn010
08-22-2016, 02:42 PM
A while ago, I receive parts and proceeded to opened up the box from a vendor. Under the cardboard flap on the bottom of the box, there was a corner of a paper sticking out, turned out to be an Amazon receipt for a Valeo clutch kit. Obviously the vendors also need to purchase parts elsewhere. Picking a random vendor (they are not whose box I opened to find the receipt), I went to the DMCH site and punched in a clutch kit.

DMCH: $275 + $150 core + shipping (With rear seal)
Amazon: $191.27 & free shipping with no core, same clutch kit
Rock Auto: $169 + $11.99 shipping

Rear main seal:
DMCH: $24 + shipping
Rock Auto (Volvo): $2.75 (Fel-Pro seal and gasket) + shipping.

I've also purchased A/C accumulators & low pressure switch which were similar to DMCH pricing. Brake pads, cabin fan resistor, tie-rod ends, and many, many other similar things were cheaper than vendor pricing.

I'm not all out against using vendors for parts, but after all these years I pretty much know what I can get cross referenced and what will be cheaper, and what I cannot. The vendors are great, and they definitely get my support - I spend enough of my money when it comes to things like hub carriers, interior trim, windshield, and other parts that you really cannot get elsewhere.

Edit: I guess the Clutch kit is a bad example, since it isn't really a cross referenced kit.

hillbillysims
08-22-2016, 05:52 PM
and I just KEEP learning.... thanks again for the input

Andrew
08-22-2016, 06:28 PM
The original DMC blower motor is an AC Delco part, complete with an AC Delco part number stamped in the case which is still valid 35 years later:

HVAC Blower Motor: DMCH $103.82
Rockauto: $36.79
Autozone: $26.99

Another great example is the clutch master cylinder. Since Bill discovered that cross-reference, I'll let him share that story. In contrast, the vendors have the best prices on clutch slave cylinders and clutch disk kits.

Rich_NYS
08-22-2016, 07:18 PM
I try to support the vendors first, except for parts that could have 30+ year-old plastic or rubber.

If I get sticker shock from the price of a part, I lean toward a crossover as long as it's not more expensive in the long run (as Josh mentioned.) I also prefer crossover parts that have a lifetime warranty that can be sourced from Autozone or Advance (like the Eagle starter)... worthwhile wisdom I learned from Bill.

DMCVegas
08-22-2016, 07:49 PM
The original DMC blower motor is an AC Delco part, complete with an AC Delco part number stamped in the case which is still valid 35 years later:

HVAC Blower Motor: DMCH $103.82
Rockauto: $36.79
Autozone: $26.99

Another great example is the clutch master cylinder. Since Bill discovered that cross-reference, I'll let him share that story. In contrast, the vendors have the best prices on clutch slave cylinders and clutch disk kits.

You sure it works correctly though? I thought that part was wired oppositely for the DMC-12 so it runs backwards?

Farrar
08-22-2016, 08:17 PM
FWIW, I used a Four Seasons blower motor on mine (part number 35589) and it spins correctly.

I've used most of the vendors over the years, but sometimes I need a part right away, or I can't justify the shipping cost by bundling the part with other items, so I source something locally. And as someone else said, sometimes shelf life is a factor.

content22207_2
08-22-2016, 10:01 PM
The original DMC blower motor is an AC Delco part, complete with an AC Delco part number stamped in the case which is still valid 35 years later:

HVAC Blower Motor: DMCH $103.82
Rockauto: $36.79
Autozone: $26.99


I paid $16.99 for my blower motor (lifetime warranty): http://www.autozone.com/cooling-heating-and-climate-control/a-c-heater-blower-motor/vdo-a-c-heater-blower-motor/141598_0_6648_5281/

Normal clockwise rotation, so I reversed positive/negative to make it spin counter clockwise with the stock squirrel cage.

Bill Robertson
#5939

Rich_NYS
08-22-2016, 11:07 PM
I reversed positive/negative to make it spin counter clockwise with the stock squirrel cage.

I was thinking that was all that's needed, but wasn't sure....

content22207_2
08-23-2016, 12:34 AM
DC motors are super easy to reverse direction -- just swap positive and negative leads and the motor spins the other way. That's how you move an electric winch in and out for example.

Bill Robertson
#5939

DMC-81
08-23-2016, 08:15 AM
If you are looking to save money buying cross referenced parts - you are sadly mistaken

The DMC vendor support is great, and prices are reasonable. Better than most cars in my experience.

You can waste alot of time and money hunting down cross referenced parts that may or may not work, then end up buying the dmc part anyway later. Way more expensive. I speak from experience.

+1. For major parts, research the options among vendors and read the forum / get some feedback before buying.

First, you may want to decide your restoration goal. The closer your goal is to concourse correct or mostly correct with flaws corrected means that you will need to decide whether you want a given part to be VIN correct, or whether the original one was flawed, and there's an improved version among vendors, etc.

"Research twice, buy once". :)

whocruiser
08-23-2016, 01:15 PM
I try to support the vendors first, except for parts that could have 30+ year-old plastic or rubber.

If I get sticker shock from the price of a part, I lean toward a crossover as long as it's not more expensive in the long run (as Josh mentioned.) I also prefer crossover parts that have a lifetime warranty that can be sourced from Autozone or Advance (like the Eagle starter)... worthwhile wisdom I learned from Bill.

Same here for the most part (no pun intended, LOL)

I recently put in one of the Eagle starters as preventive maintenance when my original stock starter (one of the relatively few items on VIN 1150 that was not swapped out for new during the previous owner's 2008 frame-off resto at DMCFL) began to show classic symptoms of getting ready to fail. I went with the Eagle unit for both the lifetime warranty by a big national chain (Autozone in my case) and the price ($99 part and only $25 for the core charge, plus a 20% off the total order promo that month, plus a $10 gift card bonus, just can't beat that!) It should be noted however that I could NOT just pick it up instantly at a local location, as HAD been the case until quite recently. Both Autozone & also Advance Discount Auto Parts, the two biggest major national chains with local stores in my area, have shifted this part from being stocked locally to being an exclusive "shipped free to you or your local store for pickup in several days" status, thereby negating one of the chief reasons I had for getting it - the ability to get one pretty much on the spot without having to wait for shipping if it fails out on the road in B.F.E. :-( I also had that rationale for putting in the Saturn alternator last year, which is still offered as locally available stock OR shipped out if temporarily out of stock locally. The alternator I got through Advance (was $10 less than Autozone with a higher core fee, but I was returning the core the next day anyway.) Already took advantage of the lifetime warranty on that alternator as the voltage regulator on it crapped out after 9 months, and they did happily exchange it on the spot, no waiting, but I fear that this part will eventually also slip into "shipped out only" status as demand dwindles along with the numbers of Saturns still on the road.

whocruiser
08-23-2016, 01:35 PM
only $25 for the core charge

Oh, and by the way, I've still got the old original factory equipment Paris Rhone starter sitting in an Autozone box on a shelf. Anyone know of a vendor (or private owner) who'd offer me more than (or even the same as, plus allowing some extra for shipping costs too, it would probably fit in a Postal Service Large, or POSSIBLY Medium, flat rate box) the $25 I'd get by simply dropping it off at my local Autozone? It's currently (again no pun intended) operable, but cranks slower and more labored when hot from multiple starts in short succession and/or long hot highway drives, which I'm told is a symptom of needing the brushes cleaned and/or replaced, and or the windings redone. Would rather see it re-used within the DeLorean community for someone seeking an accurate original part than just dropping it off at Autozone to disappear into their system.

I guess once I post this here, I'll also put a link to the post in the used parts for sale section too... ;-)

DMCVegas
08-23-2016, 07:11 PM
DC motors are super easy to reverse direction -- just swap positive and negative leads and the motor spins the other way. That's how you move an electric winch in and out for example.

Bill Robertson
#5939

Right. But now the external housing would be positive, meaning that it can short out much easier to blow a fuse by simply touching it.

content22207_2
08-23-2016, 09:32 PM
Right. But now the external housing would be positive, meaning that it can short out much easier to blow a fuse by simply touching it.

Evaporator box is made of plastic -- non conductive (just like the car itself...).

Plastic evaporator box mounted to a fiberglass dashboard -- I'm good.

Bill Robertson
#5939

content22207_2
08-23-2016, 10:02 PM
Right. But now the external housing would be positive, meaning that it can short out much easier to blow a fuse by simply touching it.

Exactly what does Robert think happens if you touch a power wire to a negative ground housing?

Tomato tomato....

Bill Robertson
#5939

Josh
08-24-2016, 01:30 AM
Right. But now the external housing would be positive, meaning that it can short out much easier to blow a fuse by simply touching it.

I agree, electrifying the external housing is kind of dumb.

but i dare not challenge the genius that is bill...

content22207_2
08-24-2016, 02:16 AM
Um, negative *IS* electrified. In fact that is the source of DC flow -- current flows from negative to positive (Ben Franklin got it backwards).

In the late 40's/early 50's some car companies went through a phase of trying to sort everything out with positive grounded vehicles, but they never caught on.

On a metal bodied car current flows through the entire car structure back to the battery. Works much better than DeLorean's daisy chains of ground wires.

If you ever wonder why steel fasteners weld themselves to your PRV, it's because the engine is electrically charged all the time. Add moisture and the dissimilar metals become miniature batteries, sharing electrons until they become one.

Irrespective, the evaporator box is electrically neutral because it is non-conductive, just like the plastic distributor cap that insulates ignition voltage from the negative grounded distributor body.

Bill Robertson
#5939

Farrar
08-24-2016, 02:24 AM
In the case of the blower motor, you wouldn't be blowing a fuse, anyway -- just tripping the auto-reset breaker. If nothing else, that would make troubleshooting easier...

content22207_2
08-24-2016, 02:33 AM
This whole tempest in a teapot is nothing more than a controversy in search of a crisis. There is no difference between touching a positive lead to a negatively grounded frame and touching a negative lead to a positively grounded frame -- effect is exactly the same: a short circuit (objective is not to touch either...).

If the evaporator box itself was negatively grounded then there would indeed be a problem because a positively grounded blower motor frame would essentially be a giant positive lead. But the evaporator box isn't grounded -- it's a big piece of electrically neutral plastic. Moreover, it is attached to an electrically neutral fiberglass underbody. Without a complex web of ground wires, the entire car body is electrically neutral for crying out loud (try disconnecting that bolt behind the parcel shelf and see what happens...).

Bill Robertson
#5939

Farrar
08-24-2016, 02:40 AM
a controversy in search of a crisis

Isn't that what the internet is for? ;)

Josh
08-24-2016, 03:17 AM
I dont need a lecture on DC circuits.
As mentioned it woudnt make much to ground out the casing and trip the fuse / breaker.
How about if your evaporator is leaking or the drain tube is plugged. Seems like a bad time having water contacting the casing.

Anyway i'm done with this. The only opinion you value is your own, as you are the all mighty bill.

content22207_2
08-24-2016, 03:19 AM
Everybody running around with their hands in the air does realize that a traditional steering wheel with integrated horn is positively charged all the time? (Not the non-conductive ring you hold onto, but metal superstructure inside the horn portion is charged just waiting for you to mash it against the column ground).

Bill Robertson
#5939

content22207_2
08-24-2016, 03:30 AM
the all mighty bill.

Is it possible your personal prejudices are interfering with technical discussion?

Bill Robertson
#5939

content22207_2
08-24-2016, 03:53 AM
Just so everyone is clear: if you fill an electric motor full of water, it is by definition full of water. Doesn't matter whether the lead is positive and the chassis is negative or vice versa -- both will be under water.

Bill Robertson
#5939

DMCVegas
08-24-2016, 12:35 PM
Exactly what does Robert think happens if you touch a power wire to a negative ground housing?

Tomato tomato....

Bill Robertson
#5939

Well if you touch a power wire to a negative housing, you create a dead short for that particular power wire and it's respective circuit, obviously. Not including any other risks to it.

If you have a positive housing, you're creating a safety concern for the vehicle if anything else conductive touches it. It creates another short, but one that flows in the opposite direction. It may be a dead one that blows a fuse, a resistor, or simply trips a circuit breaker. Or it can also transfer power on that unintended ground to generate heat. Which can damage wiring, or even risk a vehicle fire.

If your DeLorean was the victim of an electrical fire, and I made you a deal where I was able to completely restore the vehicle back to it's previous condition before it ever caught fire for $76, you'd take me up on that. For $76 it would be like nothing ever happened to your car. You'd be crazy not to take me up on that offer, right?

So why would anyone cheap-out on non-OEM parts that fail to function as intended, and risk their safety? Because that $76 price difference is what you're "saving" by not buying the correct parts, but it's costing you a whole lot more on your risk management side.

content22207_2
08-24-2016, 02:26 PM
Exactly what part of "non-conductive" isn't clear?

The entire car body is non-conductive. That is why the nice people at Lotus ran ground wires everywhere. If you lay a bare positive wire against the fiberglass underbody, absolutely nothing happens (outer stainless panels are grounded from the factory for static discharge, but even those wires are sometimes missing. There's only three grounding points anyway).

It is obvious this simple solution is driving you and Josh to distraction. My recommendation therefore is for you to buy your blower motors from Houston. I will continue to get my free replacements from Autozone (after the first $16.99 any replacements are free). PM105 is a stock item that doesn't have to be ordered in (cross references to a large number of 1980's GM products).

Bill Robertson
#5939

content22207_2
08-24-2016, 02:58 PM
If you lay a bare positive wire against the fiberglass underbody, absolutely nothing happens

Clarification: if you lay a bare wire of any sort -- positive or negative -- against the car body, absolutely nothing happens. The fiberglass underbody, including integrated dash superstructure, is electrically neutral.

Bill Robertson
#5939

DMCVegas
08-24-2016, 03:05 PM
Did I say once that the underbody was conductive? Please, enlighten us all and show us where exactly I ever made such a ludicrous claim. Re-read and you will clearly see where I clearly specified the risk in reference to conductive materials.

Using this part is a hazard, plain and simple. There is a very clear reason as to why the motor housings, even on a fiberglass car, are designed to be negative: Safety.

The only distraction here is you, Bill. You prejudiced against myself, Josh in this case, and a whole slew of other people from past conversations where our only "crime" is calling you out on your misinformation. I am all for saving money, and doing things economically. My goal is to keep cars on the road, and ensure that people are able to do that in a safe manner. But safety is paramount in all aspects. If there is an aftermarket part from even a non-DeLorean vendor that can save money, or even better exceed OEM specifications, I am all for that. But when it is a sub-standard replacement such as this blower motor, then I cannot abide by it's recommendation.

You are trying to demonize anyone who is a threat to your illusion of somehow being a DeLorean messiah.

Sometimes parts are more expensive due to mark-ups, and sometimes they're simply more expensive because they're the unique, rare components which you must use.

You're trying to first put words into my mouth, and second, ridicule me for paying a higher price to DMCH, and use that as some sort of character assassination against me in order to invalidate my position on this. This isn't an opinion, Bill; it's a fact. If you're not happy about the facts that run counter to your own invalid opinions, either take it up with the laws of physics and see if you can seek a judgement in your favor to get them repealed, or take the time to learn why you're wrong.

Sometimes you've just got to buy the correct parts, even if they cost more, to get the job done right. There is nothing wrong with that as it ensures your safety and the preservation of the vehicle.

dn010
08-24-2016, 03:05 PM
Clarification: if you lay a bare wire of any sort -- positive or negative -- against the car body, absolutely nothing happens.

The car body or underbody?

The stainless skin of my car is grounded via a ground wire that is glued underneath the windshield. Touching a +12VDC from the car to the panel will not end well.

EDIT: I now see you stated above "underbody". Disregard my post.

content22207_2
08-24-2016, 03:30 PM
The stainless skin of my car is grounded via a ground wire that is glued underneath the windshield. Touching a +12VDC from the car to the panel will not end well.

That wire grounds the hood and fenders (assuming jumper wires between them are still intact). From the factory it passes underneath the windshield to one of the dash pad mounting studs (electrically neutral), then to the blower motor (EEK!), then to the rear bulkhead bolt with the rest of the car body grounds.

Quarter panels and T panel are originally grounded to the back of the frame with two wires bolted in the corners by the rear fascia (T panel is grounded by laying against the quarter panels -- no jumper wires like the hood and fenders).

Believe it or not the doors are electrically neutral (no joke: try ringing them to ground).

Bill Robertson
#5939

DMCVegas
08-24-2016, 06:04 PM
Believe it or not the doors are electrically neutral (no joke: try ringing them to ground).

Bill Robertson
#5939

Actually, no, I don't believe you at all.

Because you see, the doors actually ARE grounded. The ground wire is provided inside of the Door Wiring Harness. It attaches to the Door Lock Solenoid on the rear bolt, which in turn grounds the rest of the door.

ALL metal body panels on vehicles must remain grounded at all times. This prevents static electricity from building up so that it doesn't knock you down, or in rare cases even kill you.

content22207_2
08-24-2016, 09:54 PM
If Lotus used the door lock solenoid as the ground point that would explain why both my cars have electrically neutral doors -- I've removed solenoids from both (I just lock the doors like a pickup truck).

Does illustrate electrical weakness of a non-conductive car (like the Corvette) -- a maze of jumper wires substitutes for the ground plane. A metal bodied car is a gigantic ground plane -- anywhere you drill a hole (and perhaps scrape off some paint) is a known good ground, battery to body cable permitting. Lose one ground point on a plastic car and whole sections of the ground plane can disappear.

(Of course lack of conductivity is what keeps me from immolating myself with that Gosh Awful Autozone blower motor...).

For the morbidly curious, these are DeLorean ground points I've been able to trace out on my own cars (obviously all the K-Jet engine grounds are missing, and apparently there are details in the doors somebody may want to add. ECU tray ground has been added since earlier postings of this schematic):

45686
45687

After this schematic the rear bulkhead bolt is grounded to the frame by a cable under the coolant expansion tank, then to the battery via the cable attached to the trailing arm bracket.

Bill Robertson
#5939

DMCVegas
08-25-2016, 11:59 AM
If Lotus used the door lock solenoid as the ground point that would explain why both my cars have electrically neutral doors -- I've removed solenoids from both (I just lock the doors like a pickup truck).

So once again a "problem" with your car is a result of your own inadequate tinkering. Are you not seeing a pattern here too?



Does illustrate electrical weakness of a non-conductive car (like the Corvette) -- a maze of jumper wires substitutes for the ground plane. A metal bodied car is a gigantic ground plane -- anywhere you drill a hole (and perhaps scrape off some paint) is a known good ground, battery to body cable permitting. Lose one ground point on a plastic car and whole sections of the ground plane can disappear.

Actually, you're wrong again.

First, there is no "weakness" here. Using your logic it would make more sense to live in a metal tool shed run off of DC power in order to avoid all the pesky extra wiring involved. Even on a traditional all metal vehicle, you still have dedicated negative wires which bolt to ground elsewhere thanks to plastic bumpers, trim, interiors, etc. They're in all honesty no different than a DeLorean. Even IF components were immediately grounded directly where they were located in a vehicle by their mounting hardware, the metal sections still have common paths to ground which can be interrupted as well, and thus the entire ground plane can be severed even on a traditional vehicle.

Second, make no mistake, despite being made out of far more conductive materials, you're still going to have wiring harnesses in modern cars with a similar, if not the same design as the DeLorean with common, shared, and relocated ground points. Cabs of trucks are mounted from the chassis by way of rubber isolators, and thus are not automatically grounded. So a ground strap must still be installed between to two to provide a path to ground. If that strap gets disconnected, you've just wound up with the exact same complaint you just made about DeLoreans and Corvettes. So once again your words have proven your arguments to be invalid.

Otherwise if all the wires in a harness are too intimidating, you're always going to be having problems. Especially if you keep hacking away at vehicles without understanding them first. Exactly how many years now have you been erroneously telling people that the doors in their vehicles were not grounded from the factory because you didn't understand what you were looking at? Better yet, what else have you been wrong about, Bill?



After this schematic the rear bulkhead bolt is grounded to the frame by a cable under the coolant expansion tank, then to the battery via the cable attached to the trailing arm bracket.

Again, hardly any different from most, if not all, modern cars that utilize common paths to ground for multiple components. Just another straw man argument to try and deflect criticism. But let's get back on track with that right here:



(Of course lack of conductivity is what keeps me from immolating myself with that Gosh Awful Autozone blower motor...)

No, the fact that you've not yet grounded anything to that housing is why. Reversing those wires to energize the external housing is dangerous. It doesn't matter if the housing, nor even the underbody are non-conductive. There are plenty of other wires & surfaces under the dashboard which are. So if someone is working around that housing, if you or a passenger stuff some items into the passenger footwell, or who knows what else could cause it, there is a significant risk of shock, and/or fire.

Don't be stupid and risk your safety for a few dollars. Install the proper part the first time and this won't be a problem.

Andrew
10-02-2016, 12:04 PM
You sure it works correctly though? I thought that part was wired oppositely for the DMC-12 so it runs backwards?

This week I installed a Four Seasons 35582 blower motor on 5052. It spins in the correct direction with no wiring modifications and has the correct vent tube. For all intents and purposes it appears identical to the stock A/C Delco unit.

The total cost was less than $30.

The part crosses to a 1980 Chevy Monza V6, with A/C, with vent tube.

r00b
09-26-2019, 05:48 PM
This week I installed a Four Seasons 35582 blower motor on 5052. It spins in the correct direction with no wiring modifications and has the correct vent tube. For all intents and purposes it appears identical to the stock A/C Delco unit.

The total cost was less than $30.

The part crosses to a 1980 Chevy Monza V6, with A/C, with vent tube.

I got this same part a few years ago from Pep boys for $14,
It's 22.49 now, here is the link
https://www.pepboys.com/four-seasons-blower-motor/product/8051316