PDA

View Full Version : Frame & Body Painting Fascias



mluder
08-23-2016, 03:03 PM
Opening up a discussion here...

My fascias are tired paint is flaking in areas and generally faded overall. I'm not sure if it's the original paint or a re-spray and I'm contemplating having them re-done. At a car show recently a guy suggested not touching them if it's the original paint. That, like an antique piece of furniture, there's more value in the original faded paint as a survivor car

Discuss amongst yourselves?

Cheers
Steve

Drive Stainless
08-23-2016, 03:11 PM
You could have the best of both worlds by wrapping them with vinyl. Cheaper, too.

Rich_NYS
08-23-2016, 03:47 PM
You could have the best of both worlds by wrapping them with vinyl. Cheaper, too.

Is there a color match to one of the original codes?

Michael
08-23-2016, 03:47 PM
If the job is done right, you will not only help the value but the appearance by painting them.

Jonathan
08-23-2016, 04:04 PM
Personally, I think you add value when cleaning up something like this and not the opposite about lowering the value because it doesn't have that survivor/antique original aspect. I'd say most things on our cars don't fit into that numbers matching or original this and that mantra that other classics do. Someone would have a hard time telling you for certain that a particular area on your car didn't leave the factory that way when we don't know what way most cars left the factory ourselves anyway!

I'd like to hear what others have to say on paint codes and technique, as my front fascia is about due for some attention. Mine got done at some point before I got the car in 2007 and they had gone for the "trying to match the colour to the stainless" silver approach. I like it that way to be honest and will likely try to repaint it the colour it is when I do.

Flicky
08-23-2016, 04:13 PM
Opening up a discussion here...

My fascias are tired paint is flaking in areas and generally faded overall. I'm not sure if it's the original paint or a re-spray and I'm contemplating having them re-done. At a car show recently a guy suggested not touching them if it's the original paint. That, like an antique piece of furniture, there's more value in the original faded paint as a survivor car


A car will only be "more valuable" if it is a true survivor. These will have super low miles and tucked away for years. A Delorean will never gain much with this type of marketing as the 'bumpers', as non-D people will call them, are not the exterior part that makes the car cool.

Anything that looks bad will lower the overall desirability of the car. You may be able to con someone into the idea that they are getting original paint, but no one is really buying a Delorean for the paint. Looking at collector cars with original paint they never look bad.

Vinyl is a nice idea if you want a strange color/pattern. I think a carbon fiber pattern might look cool. It still needs prep to make it smooth so I don't know if it can really save the paint. All the cut outs and holes make it more labor intensive too.

There is also a thing called hydro-graphics if you like the idea of patterns.

DavidProehl
08-23-2016, 05:17 PM
I'm with the masses on this: paint!

Not sure I can add anything more. I agree that a great looking car is going to be worth more than a cracked and faded one. There are plenty of original paint jobs yet out there, you won't be able to compete with them when selling with your original cracked and faded paint.

Fresh paint lets you enjoy it more, and I expect will attract more buyers.

Lwanmtr
08-23-2016, 05:34 PM
Yep, I'll add my 2 cents.... Paint them, definately. Otherwise you'll look at them every day and see how bad they look against the nice stainless panels.

DMC-81
08-23-2016, 09:02 PM
Agreed. Have a quality shop paint them. If you are concerned with originality, get the vin correct paint codes from DMC, and have the shop pay attention to the details.. like the bottom being un-painted.

I did this when I had my fascias and louvre painted. I chose a well recommended shop that specializes in classic cars, and could paint in my vin correct oil based paint. I actually marked the areas that were not to be painted with marker on painters tape, and I stressed to the shop manager that I wanted the most experienced tech doing the work. They turned out well.

Here's a couple pics..

45667

45668

Lwanmtr
08-23-2016, 09:22 PM
If you decide to tackle it yourself, be patient with the sanding and blending cause thats where most of the work is.

Gfrank
08-23-2016, 11:05 PM
Nothing drags down the appearance of a DeLorean then some poor bumpers imo

mr_maxime
08-23-2016, 11:29 PM
What's a good price for getting the fascias painted? I was quoted $800-$950 by a shop but this seems high for such a small amount of car to paint. My dad was quoted $3000 for his entire TSX with 3 coats of "german" paint.

DMC-81
08-23-2016, 11:41 PM
What's a good price for getting the fascias painted? I was quoted $800-$950 by a shop but this seems high for such a small amount of car to paint. My dad was quoted $3000 for his entire TSX with 3 coats of "german" paint.

I don't know if there are regional price differences, but that sounds about right. Mine was more, but I had the louver painted as well. Also, I was quoted $500 to repaint the front fascia on my daily driver as an extra during work that was already being done.

I believe that in professional painting, you most often get what you pay for.

Lou and "Boo"
08-23-2016, 11:57 PM
I'm with Matt on this one. Wrap them !

Lou and "Boo"
08-23-2016, 11:58 PM
Oh and SEM trim black works great on the louver .

cdrusn
08-24-2016, 12:09 AM
I have both my front and rear off getting them ready for the paint shop. A lot of sanding due to multiple layers of previously applied paint, ended up using a sharp razor blade to carefully remove the old paint. The color is partly dependent on the VIN with the earlier bumpers painted to match the stainless and the newer ones a darker color. I used this thread to help remove them: http://delorean6575revisited.blogspot.com/2013/03/removing-and-reconditioning-front-and.html#!/2013/03/removing-and-reconditioning-front-and.html
There is also another thread that listed several paint codes. I couldn't use the paint code from 2009 because it was water based paint and we don't use that here. Make sure you use an adhesion promoter so the paint will not flake off or crack when you are putting the bumper back on. One quart of mixed paint, hardner (added to the paint to make a matte finish without clearcoat), bulldog adhesion promoter was $309 and I expect the painter to be about $200 per bumper. That's with me taking them off and prepping them. :race:

DMC-81
08-24-2016, 06:52 AM
Oh and SEM trim black works great on the louver .

Agreed. That's what I asked my paint shop to use. But, they said that the paint's matte finish wouldn't stand up as well to car washes, and minor abrasions etc. so, they employed a matte clear coat over it. I thought it was a nice feature to maintain the look while providing better duriblity, and they didn't charge me extra.

Here is a picture of what it looks like.

45671

Drive Stainless
08-24-2016, 07:44 AM
Agreed. That's what I asked my paint shop to use. But, they said that the paint's matte finish wouldn't stand up as well to car washes, and minor abrasions etc. so, they employed a matte clear coat over it. I thought it was a nice feature to maintain the look while providing better duriblity, and they didn't charge me extra.

Here is a picture of what it looks like.

45671

And that's how a real auto paint shop should apply satin black - using a professional, urethane, two-component black paint with a two-component satin clear. :thumbsup:

SEM in a rattle can is the DIY-er's weapon of choice.

Gfrank
08-24-2016, 08:42 AM
What's a good price for getting the fascias painted? I was quoted $800-$950 by a shop but this seems high for such a small amount of car to paint. My dad was quoted $3000 for his entire TSX with 3 coats of "german" paint.

Differ depending on location, but we are generally $450 a panel these days

Morpheus
08-24-2016, 10:10 AM
Agreed. Have a quality shop paint them. If you are concerned with originality, get the vin correct paint codes from DMC, and have the shop pay attention to the details.. like the bottom being un-painted.

I did this when I had my fascias and louvre painted. I chose a well recommended shop that specializes in classic cars, and could paint in my vin correct oil based paint. I actually marked the areas that were not to be painted with marker on painters tape, and I stressed to the shop manager that I wanted the most experienced tech doing the work. They turned out well.

Here's a couple pics..

45667

45668

I will have to ask you what shop you used when it's time for me to paint mine!

Jonathan
08-24-2016, 10:15 AM
Differ depending on location, but we are generally $450 a panel these days

Gary, "we" like you and your shop out in the East end of the GTA? My fascias might be something I do over the winter and would be good to have some local options I know and trust.

mluder
08-24-2016, 07:33 PM
I have both my front and rear off getting them ready for the paint shop. A lot of sanding due to multiple layers of previously applied paint, ended up using a sharp razor blade to carefully remove the old paint. The color is partly dependent on the VIN with the earlier bumpers painted to match the stainless and the newer ones a darker color. I used this thread to help remove them: http://delorean6575revisited.blogspot.com/2013/03/removing-and-reconditioning-front-and.html#!/2013/03/removing-and-reconditioning-front-and.html
There is also another thread that listed several paint codes. I couldn't use the paint code from 2009 because it was water based paint and we don't use that here. Make sure you use an adhesion promoter so the paint will not flake off or crack when you are putting the bumper back on. One quart of mixed paint, hardner (added to the paint to make a matte finish without clearcoat), bulldog adhesion promoter was $309 and I expect the painter to be about $200 per bumper. That's with me taking them off and prepping them. :race:

Thanks for the advice... For some reason the pics don't load in the link you shared. Hmmm....

Steve

Gfrank
08-24-2016, 10:09 PM
Gary, "we" like you and your shop out in the East end of the GTA? My fascias might be something I do over the winter and would be good to have some local options I know and trust.


Yup, that's a general ball park for my shop rate, that being said I could likely do better on a DeLorean bumper ;)

sdg3205
08-25-2016, 03:22 AM
When i got 3205 the front fascia looked like a piece of undercooked toast. Somehow, the back was still quite nice. I wanted to paint them the early VIN darker, glossier colour, but my friends in the restoration world said "it's only original once." They convinced me to colour match the front to the back and clean up the back with some polishes. I'm glad I did. Is that something you could do, or are they both in rough shape? If they're both pretty rough, just repaint them, but do it professionally. I've never been 100% happy with my own paint work unless it was high-heat engine paints. You probably saw on Facebook in July i did my own body work and paint work on my Jeep. It's much better, but not pro. Painting is one of those things I just think has to be done professionally, or at least with professional gear.

David T
08-25-2016, 02:32 PM
In the real world of buying and selling Deloreans, you will not diminish the value of the car by having the facias repainted just as long as it is done so it looks like it did originally. If you are going to do a bad job you are better off leaving it alone. To do it properly it is better to remove them and have them both painted off the car. Be prepared to replace/repair a lot of broken studs and it is a pain to get them back on and lined up. You might also have to refresh other trim and replace some lenses so the car looks "even". Maybe also regraining the whole car. Freshly repainted facias may make the rest of the car look tired so you may have to do a lot of other stuff to make it all look proper. Maybe repainting the rims too. Depends on the general condition of the whole car. Better to have a plan BEFORE you start so you know where you want to end up.

mluder
08-28-2016, 01:41 PM
When i got 3205 the front fascia looked like a piece of undercooked toast. Somehow, the back was still quite nice. I wanted to paint them the early VIN darker, glossier colour, but my friends in the restoration world said "it's only original once." They convinced me to colour match the front to the back and clean up the back with some polishes. I'm glad I did. Is that something you could do, or are they both in rough shape? If they're both pretty rough, just repaint them, but do it professionally. I've never been 100% happy with my own paint work unless it was high-heat engine paints. You probably saw on Facebook in July i did my own body work and paint work on my Jeep. It's much better, but not pro. Painting is one of those things I just think has to be done professionally, or at least with professional gear.

Paint is too far gone for a rehab.
I'll definitely have it done by a pro.
I believe my VIN is in the low luster category but I really like the gloss so I'm not sure which way to go with this.

Cheers
Steve

mluder
08-28-2016, 01:44 PM
In the real world of buying and selling Deloreans, you will not diminish the value of the car by having the facias repainted just as long as it is done so it looks like it did originally. If you are going to do a bad job you are better off leaving it alone. To do it properly it is better to remove them and have them both painted off the car. Be prepared to replace/repair a lot of broken studs and it is a pain to get them back on and lined up. You might also have to refresh other trim and replace some lenses so the car looks "even". Maybe also regraining the whole car. Freshly repainted facias may make the rest of the car look tired so you may have to do a lot of other stuff to make it all look proper. Maybe repainting the rims too. Depends on the general condition of the whole car. Better to have a plan BEFORE you start so you know where you want to end up.

Wheel repair and paint is another on my list of things to do.
A regrain definitely makes sense with the fascias off. I have a flapper wheel and correct speed drill but the few times I've tried it the grain wasn't real even and parallel. Probably just need more practice or is this something the blending pad will correct?
I've had my rear one off before with no issues - Lucky I guess. Hope the front goes as easily.

Cheers
Steve

David T
08-28-2016, 04:04 PM
Wheel repair and paint is another on my list of things to do.
A regrain definitely makes sense with the fascias off. I have a flapper wheel and correct speed drill but the few times I've tried it the grain wasn't real even and parallel. Probably just need more practice or is this something the blending pad will correct?
I've had my rear one off before with no issues - Lucky I guess. Hope the front goes as easily.

Cheers
Steve

If you can't regrain properly with a power tool I suggest you try doing it by hand until you are proficient. You cannot fix any mistakes with a blending pad, you must do it correctly BEFORE that. A typical regain starts with #80 grit possibly finishing up with a blending pad. You can regrain with the facias attached. You just mask them but if they are removed it is a bit easier. To try to regrain straight try using masking tape to give you a straight line as a guide. It is natural for the human body to do things in an arc, part of the learning process is to train yourself to hold a straight line.