Log in

View Full Version : General Does Anyone know what this IS!! Please



MJH
09-06-2016, 04:30 PM
Hi All
Nearly completed the full restoration of 10169 fitted with BAE Turbo set up

I have come across the part which I don't really know what it is !!!and where it goes !! and what function it does.
Any info or suggestions would be really appreciated.

Car seems to run ok without it but running very rich on idle, so I am wondering if this part has something to do with that maybe.

Many thanks Mike

Bitsyncmaster
09-06-2016, 04:33 PM
Looks like a pressure switch of some kind. Maybe vacuum switch. Have not seen it on my stock D.

MJH
09-06-2016, 04:50 PM
Looks like a pressure switch of some kind. Maybe vacuum switch. Have not seen it on my stock D.

Hi Dave
Yes I thought the same maybe it's only fitted to Deloreans with Turbos
Thanks Mike

DMCVegas
09-06-2016, 04:59 PM
I don't see anything resembling this part in the BAE installation instruction manual.

http://www.deloreanclub.de/BAE-Instructions.pdf

It almost looks like the first Hobbs Switch from an Island Twin Turbo kit that gets mounted on the left side of the intake manifold. Which makes me wonder if perhaps that's what someone was going after here.

MJH
09-06-2016, 05:04 PM
I don't see anything resembling this part in the BAE installation instruction manual.

http://www.deloreanclub.de/BAE-Instructions.pdf

It almost looks like the first Hobbs Switch from an Island Twin Turbo kit that gets mounted on the left side of the intake manifold. Which makes me wonder if perhaps that's what someone was going after here. Take a look at this BAE installation, and the extra vacuum line being ran off the left, front side of the manifold boss (previously sealed thanks to the instructions of CIS that abandoned the old Auxiliary Air Valve).

http://iudexmaximus.delorean.fr/gallery/40_1289733370.jpg

Hi Robert
Thanks for your response, I have also looked at the BAE instructions and could,not find it either!
Cheers Mike

DMCMW Dave
09-06-2016, 05:05 PM
The purpose of that Hobbs switch on the Island kit was to short the O2 sensor to ground, driving the ECU to full rich (under full boost only). Looks like a variation on the theme. I suppose it the switch was bad (i.e. shorted) you'd see an issue, but that would show up when you measure the ECU dwell. It would look like a bad O2 sensor and you'd never be able to set the CO mixture.

FABombjoy
09-06-2016, 05:17 PM
Agree with this thread, looks like an older version of adjustable vacuum switches. I use one of these along with a Hobbs switch to control open-loop fueling.

BAE / Island used boost switches to go open loop under boost. A vac switch could be misused to provide on-boost enrichment, if you set it to open as close to atmospheric as possible. You'd be laggy and smoky but it would work.

That type of vacuum switch can also be used to electrically bypass a defective warm up regulator, should the vacuum plumbing to the WUR not look standard.

Regarding the blue vac line visible in the above photo on the LH manifold near the BAE intake adapter - on a standard BAE install that is connected to the wastegate. On most turbo kits wastegate is connected directly to the compressor housing. Not sure if BAE did it this way because there wasn't any provision on the Rajay compressor housing or if it was done to dial out a teensy bit of turbo lag. I'm guessing the latter.

DMCVegas
09-06-2016, 06:02 PM
Regarding the blue vac line visible in the above photo on the LH manifold near the BAE intake adapter - on a standard BAE install that is connected to the wastegate.

That is absolutely, positively correct. I re-read the instructions and saw that. It's why I deleted that incorrect line from my last post, but MJH saw it before the save was completed.

Even the schematics on the Island Twin Turbo schematic don't show the same switches and pulls, but who knows if this was apart of the BAE system post-installation. And if so, *why* was it installed? We've all seen POs do stranger things than this to our cars, so who knows...

Michael
09-06-2016, 06:14 PM
Could it be part if an aftermarket boost controller?

FABombjoy
09-06-2016, 06:23 PM
There may have been multiple install guides, too. The BAE scan I have mentions a pressure switch but doesn't have any wiring diagram. The Island has the user drill and tap the intake manifold which is a pain. It would have been easy to integrate it into their manifold adapters. I had a bung welded into the my BAE charge pipes so I didn't have to disturb the intake - that's how they really should have been delivered.

Actually the Island scan I have has some kind of nonsense twin hobbs switch method. You can leave all of the O2 sensor wiring alone and create the same result by grounding terminal 11 on the K-jet controller.

Both kits left a lot of room for improvement and it would be interesting to see a list of what other owners put into place over the years. Some of what I've seen is scary enough that I have a bit of respect for what the B28F can stand up to. As long as you don't turn up the boost too far, anyway.

FABombjoy
09-06-2016, 06:29 PM
Could it be part if an aftermarket boost controller?
Those usually have twin/tri vacuum ports separated by a solenoid or a spring / valve chamber of some sort.

Michael
09-06-2016, 06:43 PM
I had an Apex Intergration AVC boost controller on my 300hp Talon and that thing had more vacuum diaphragms that I can remember. Very complex outfit.

FABombjoy
09-06-2016, 06:51 PM
Haha, a friend of mine converted a twin turbo RX7 into single and could have opened his own vacuum valve store.

APEXi... now there's a name I haven't heard in a long, long time.

DMCMW Dave
09-06-2016, 07:10 PM
I had an Apex Intergration AVC boost controller on my 300hp Talon and that thing had more vacuum diaphragms that I can remember. Very complex outfit.

The good old days pre Aftermarket Engine Computers. . .

David T
09-06-2016, 07:15 PM
It is some kind of switch to sense pressure or vacuum. Under boost you need to do some things. One thing is to get more fuel and most of the turbo systems force the Lambda system into full rich. You can do that by messing with the O2 sensor or the WOT switch. You also have to limit spark advance.
Next, if you do mess with the O2 sensor and you have an A/F meter you need to keep it connected to the O2 sensor if you are grounding the wire from the Lambda ECU.
Some control the solenoid going to the vacuum advance on the distributor. Depending on if you have 1 or 2 Hobbs switches and if they are NC or NO or both, you can do a lot with relays. There are also some who use the Control Pressure Regulator to get a little more fuel. Additionally some have tried wiring up the cold start valve to dump more fuel in. Finally some have tried water injection. My notes for the BAE have a pressure switch penciled in at the end of the parts list but the instructions don't say how to hook it up. Many of the turbo systems have been "customized", so there is no standard. The goal has been to try to prevent detonation and keep the boost limited to 5 psi.