PDA

View Full Version : Heat & A/C Air con problem



Antileon
09-10-2016, 02:53 PM
My aircondition runs, I can hear the blower running but get no air through any of the vents ? any suggestions, thanks

Jonathan
09-10-2016, 03:15 PM
http://support.delorean.com/kb/a75/mode-switch-failure.aspx

Rich
09-10-2016, 03:15 PM
My aircondition runs, I can hear the blower running but get no air through any of the vents ? any suggestions, thanks

Maybe the main/central A/C face vent flaps (manually set with rotary wheel for each center vent) are somehow set to closed position. Check that first.

Not even any air thru even the door/armrest vents in A/C mode?

Bitsyncmaster
09-10-2016, 04:56 PM
Maybe the main/central A/C face vent flaps (manually set with rotary wheel for each center vent) are somehow set to closed position. Check that first.

+1
Beleave it or not but I know someone that pulled the vent off and it turned out to be just that.:bash:

Antileon
09-10-2016, 04:57 PM
Maybe the main/central A/C face vent flaps (manually set with rotary wheel for each center vent) are somehow set to closed position. Check that first.

Not even any air thru even the door/armrest vents in A/C mode?

The 2 metal flaps behind the main center vents are closed, no air from door or any other vents, not even from window vents

Antileon
09-10-2016, 04:58 PM
+1
Beleave it or not but I know someone that pulled the vent off and it turned out to be just that.:bash:

pulled the vent off ?

Rich
09-10-2016, 05:32 PM
pulled the vent off ?

The center pair of vent registers can be removed by carefully prying the keeper tabs on the inner faces.

But if you are not even getting any flow out of the ducts at either end of the dash that feed the door vents then the center vents are not the problem.

Either there is blockage somewhere or the fan wheel isn't spinning.

Along the blockage line how long ago did this problem start?

DKDMC
09-10-2016, 07:59 PM
Mode switch malfunction? May want to rebuild it and replace diaphragm?

Antileon
09-11-2016, 05:13 AM
The center pair of vent registers can be removed by carefully prying the keeper tabs on the inner faces.

But if you are not even getting any flow out of the ducts at either end of the dash that feed the door vents then the center vents are not the problem.

Either there is blockage somewhere or the fan wheel isn't spinning.

Along the blockage line how long ago did this problem start?



The flaps in the center duct remains closed and show resistance when I try and push them open.

I have never used the AC before. Got the car recently

Antileon
09-11-2016, 05:15 AM
Mode switch malfunction? May want to rebuild it and replace diaphragm?

When I use the mode switch I hear the ventilator start up, but the air is not getting into the car, regardless of mode switch selection.
When I engage the fan speed I can hear increased revolutions of the fan.

PJ Grady Inc.
09-11-2016, 11:30 AM
When I use the mode switch I hear the ventilator start up, but the air is not getting into the car, regardless of mode switch selection.
When I engage the fan speed I can hear increased revolutions of the fan.
Since you're not getting air from any vent it is most likely a bad mode switch diaphragm. We have rebuilt switch's on our website. If you get an intermittent hissing noise at the switch area while changing modes then that would confirm a bad diaphragm.
Rob

Antileon
09-12-2016, 10:04 AM
Since you're not getting air from any vent it is most likely a bad mode switch diaphragm. We have rebuilt switch's on our website. If you get an intermittent hissing noise at the switch area while changing modes then that would confirm a bad diaphragm.
Rob

If it was the switch,. would I hear the fan running ?

Jonathan
09-12-2016, 11:01 AM
http://support.delorean.com/kb/a75/mode-switch-failure.aspx


If it was the switch,. would I hear the fan running ?

Did you read the article in the link provided to you? It answers most of the questions you posted in this thread.

Antileon
09-13-2016, 03:16 PM
Did you read the article in the link provided to you? It answers most of the questions you posted in this thread.

Yes I read the document on the link, thanks, but the fan is responding to the control knob but something is blocking the airflow

Jonathan
09-13-2016, 09:19 PM
Yes I read the document on the link, thanks, but the fan is responding to the control knob but something is blocking the airflow

It still means the same problem and solution. The fan speed knob changes fan speeds. The mode control switch will tell whether the fan should be on at all, but the air flow direction comes from the vacuum tubing and seals on the back of the mode control switch.

David T
09-13-2016, 10:30 PM
While it is usually the mode switch it can be anything that prevents vacuum from getting to the mode switch too. We have seen the vacuum hose pinched under the console, the hose unattached to the motor, etc. You should start by verifying you actually have vacuum AT the mode switch. You can do it without any tools. Take a scrap of paper and place it on the hose with NO trace stripe. It should stay there without falling off. Of course you must do it with the motor running! Refer to N:08:15 in your Workshop Manual. If you have vacuum there replace the diaphragm and that should do it. If you don't have vacuum you must figure out why.

Andrew
09-14-2016, 01:13 PM
Since you indicated that the metal flap by the vent doors is not opening, I would recommend checking the actuator that operates that flap. The plastic rod that attaches the actuator to the metal rod on the air box broke on 5052 causing a lack of air from the center vents (I can't recall whether it also caused a lack of air from the door vents as well.) Either way, if that actuator has broken, you should still get air from the defroster and the heat vents when the mode switch is set to those respective positions. Thus, if you aren't getting air from any vents at any setting I would go with Rob's diagnosis of a mode switch.

On an aside, have you confirmed that the fan is spinning the correct way?

Best of luck,

Andrew
4194
5052