View Full Version : Transmission Auto Best option for replacement Auto Trans Computer?
Mattglas
09-13-2016, 05:07 PM
My auto transmission is shifting slowly and slips out of gear when going into third. So, I'm looking into getting a new computer, but what's the best replacement? So far it's between sending mine in to DMC Texas to get rebuilt or ordering a "new" one from Specialtauto. Can anyone vouch for these products? Also should the solenoid valves be replaced? I saw that in a thread somewhere, wasn't sure if it was necessary.
DMCMW Dave
09-13-2016, 06:55 PM
My auto transmission is shifting slowly and slips out of gear when going into third. So, I'm looking into getting a new computer, but what's the best replacement? So far it's between sending mine in to DMC Texas to get rebuilt or ordering a "new" one from Specialtauto. Can anyone vouch for these products? Also should the solenoid valves be replaced? I saw that in a thread somewhere, wasn't sure if it was necessary.
What do you mean by slips out of gear? Does it drop into second perhaps when it should be in third? If you want to test the trans itself, get the car up to the high end of second gear and pull out fuse #13. It should go into third and stay there (an assistant is handy for this, it's an awkward motion). If you pull that fuse and it still slips you have other issues. But 99% of the time it's just the governor.
The SpecialT version requires you to cut into the wiring harness to install it. It is not a new governor by any stretch, it is a box that wires around the dead electronics on the one in the car. Not good for ultimate core value. We've removed a few due to faulty wiring, some skill is involved to install it reliably.
We sell the DMCH version, probably over a hundred, maybe even 200, at this point, never seen a failure. This re-uses your original unit but all the electronics inside are replaced. When back in the car it appears original.
I've only ever replaced one solenoid. They never fail.
Delorean Industries
09-13-2016, 07:12 PM
Agreed with Dave on this. Rebuilding/updating the stock boards is the only reasonable route. Not a good idea to splice into a good harness unless extensive damage from the cross over tube is present.
Ryan King
09-13-2016, 08:43 PM
If you follow this method like I did, you won't have to remove all the plugs from the transmission.
http://dmctalk.org/showthread.php?7648-How-To-Remove-the-Automatic-Transmission-Governor-Computer
This I found to be the best method. I had mine rebuilt by DMCMW and they did a fabulous job, turn around time of a couple days. Fixed all my slipping/shifting issues.
Or, if you haven't done anything to the transmission, now is a good time to drop the pan. Clean or change out the filter. Change the fluid and check overall condition on the inside of the transmission. And I would recommend switching to Josh's Silicone gasket. Beats the heck out of the stock cork gasket.
http://www.deloreanindustries.com/29-transmission-pan-gasket-silicone/
Hope this helps!
-Ryan
Jonathan
09-13-2016, 09:17 PM
I put a DMC Houston/Midwest shift computer rebuild into my car in 2010 and have not had a single problem with it since. That would be the one that gets my vote.
Do though take the suggestion of checking that it is indeed a failed shift computer and not fluid related. Do the fuse test Dave mentioned. Also confirm your fluid levels are fine and so too is your filter. More often than not automatic owners with problems shifting will find out it is the shift computer gone bad, but we have also seen other problems around plugged filters or cracked internals.
Measure twice and cut once, bud! Make sure you need a new shift computer before you pull the trigger.
Mattglas
09-13-2016, 09:33 PM
What do you mean by slips out of gear? Does it drop into second perhaps when it should be in third?
My dad was driving at the time so this isn't a first-hand experience. Basically what happened was that it would slowly shift from first, second, and then to third, but stepping on the pedal after costing (from third) would result in no throttle response almost like being in neutral. After slowing down for a bit it would catch again and drive just fine.
Mattglas
09-13-2016, 09:42 PM
Or, if you haven't done anything to the transmission, now is a good time to drop the pan. Clean or change out the filter. Change the fluid and check overall condition on the inside of the transmission. And I would recommend switching to Josh's Silicone gasket. Beats the heck out of the stock cork gasket.
-Ryan
Thanks for the advice, will definitely replace the filter/gasket after hearing how terrible the originals were.
David T
09-13-2016, 10:23 PM
Thanks for the advice, will definitely replace the filter/gasket after hearing how terrible the originals were.
One option, if you are handy, is to repair the shift computer yourself. If you can handle a soldering iron you can do it. It isn't that hard. The parts are inexpensive. In fact, the most work is actually taking the shift computer out and putting it back in. While you are checking things out run your hands over the wiring harness cables and make sure they have not been burned and are securely away from the exhaust pipes. Of course check all of the other things anyway like the fluid levels, the cable adjustments, etc. Not only must the level be good the fluid should be nice and red and not smell burnt. BTW, there was/is nothing wrong with the original filter or the gasket. The filter can be cleaned and reused if you are trying to save money. You should replace the pan gasket if you remove the pan. Make a note of the amount of debris in the pan and on the magnet. The higher the mileage the more you can expect. NEVER drive on a bad shift computer, it will damage the mechanical internals of the transmission making for a much bigger and more expensive repair.
DMCMW Dave
09-13-2016, 11:39 PM
My dad was driving at the time so this isn't a first-hand experience. Basically what happened was that it would slowly shift from first, second, and then to third, but stepping on the pedal after costing (from third) would result in no throttle response almost like being in neutral. After slowing down for a bit it would catch again and drive just fine.
That doesn't sound as much like the governor as it sounds like an internally failing transmission OR one that is very low on fluid. Check the fluid hot. A bad governor can fool you though as it may be dripping all the way in to first, but anytime someone says the engine goes "like in neutral" it's not usually the governor. I'd still replace it first as I have been fooled, and compared to replacing the whole trans it's cheap to try. And you'll need one anyway, most of the originals are long-failed at this point.
Jonathan
09-14-2016, 09:45 AM
That doesn't sound as much like the governor as it sounds like an internally failing transmission OR one that is very low on fluid. Check the fluid hot. A bad governor can fool you though as it may be dripping all the way in to first, but anytime someone says the engine goes "like in neutral" it's not usually the governor. I'd still replace it first as I have been fooled, and compared to replacing the whole trans it's cheap to try. And you'll need one anyway, most of the originals are long-failed at this point.
Two summers ago I had this "like in neutral" no power thing. Turned out my auto trans filter was plugged. When it happened, I was able to limp home from only a mile or two away. Shutting the car off seemed to let whatever was plugged up in the filter to fall back down again and return the power to the car. A couple more blocks and it would happen again. Got home and thanks to some kind of magical forces at play, Michael literally had just advertised his replacement filters were now available. Put the new filter in when it arrived along with new fluid and we were good to go again.
Mattglas
09-14-2016, 01:55 PM
Two summers ago I had this "like in neutral" no power thing. Turned out my auto trans filter was plugged. When it happened, I was able to limp home from only a mile or two away. Shutting the car off seemed to let whatever was plugged up in the filter to fall back down again and return the power to the car. A couple more blocks and it would happen again. Got home and thanks to some kind of magical forces at play, Michael literally had just advertised his replacement filters were now available. Put the new filter in when it arrived along with new fluid and we were good to go again.
Hopefully it's that simple of a fix! Dave's "internal failure" diagnostic guess has me worried. Speaking of Michael, I just ordered his filter/dpi's silicone gasket last night, hopefully that gets me somewhere.
Anyways, David's diy suggestion sounds interesting/cheaper. Though, having all new electronics in there sounds like the best bet.
DMCMW Dave
09-14-2016, 03:53 PM
Hopefully it's that simple of a fix! Dave's "internal failure" diagnostic guess has me worried. Speaking of Michael, I just ordered his filter/dpi's silicone gasket last night, hopefully that gets me somewhere.
Anyways, David's diy suggestion sounds interesting/cheaper. Though, having all new electronics in there sounds like the best bet.
You have nothing to lose trying to rebuild it yourself, but it's harder than it looks. The old circuit boards are made of something akin to wax paper.
There are several online resources that detail the procedure, I don't recall where offhand but I'm sure you can find them. Just don't louse up the core (i.e. don't break off the three small internal wires, don't cut any of the large wires) or then the upgrade won't be possible.
Mattglas
09-14-2016, 07:25 PM
So getting of the topic of the transmission. I hooked up my dwell/rpm meter to the positive side of the coil and to ground like some guy on YouTube showed. After starting and the needle not moving I shut off the car and removed the meter. Now my car wont start and there's no spark... Did I fry the coil?
Dangermouse
09-14-2016, 07:35 PM
You would be better starting a new thread. We have engine experts that would t even open an AT thread :)
Mattglas
09-15-2016, 12:35 AM
You would be better starting a new thread. We have engine experts that would t even open an AT thread :)
True. I just didn't want to spam the help page.
DMCVegas
09-15-2016, 02:13 AM
True. I just didn't want to spam the help page.
Legitimately asking questions is not SPAM. Don't sweat it. :)
Dangermouse
09-15-2016, 09:06 AM
True. I just didn't want to spam the help page.
You can never ask too many questions in the General Discussion page. ;)
That's what we are here for.
Separate threads help attract the right advice, and also are useful for members searching in the future for help with a similar problem.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.