PDA

View Full Version : Engine High Idle, no power, hard to start, rough. pfffffff



Mrdashbo
09-17-2016, 12:16 PM
Hello All,

I'm literally at the end of my rope with my car, I can't get it to idle normally and its running very rough. When I drive it, it takes ages to wake up and even then it misfires (pops n pips) and the power is rubbish. I'm methodically going through all the obvious and possible causes but getting nowhere. It always seems very hot even though the temp gauge is accurate and reads normal. (new radiator and fans and otterstat) Although today it did overheat in my driveway due to an airlock but that's another tale. I could really do with some advice as I feel like I am getting nowhere and seeing no improvements at all.

Here is what I have done recently to try to fault find and cure any potential issues.

I have removed the intake manifold and replaced the idle speed thermisitor and the thermal vacuum switch along with all 3 hoses (hoses are in the correct position and manifold gaskets are in good condition too). I have also put in a new vacuum solenoid (although I wasn't sure which way the electrical connector went on as its not marked) Idle switch has been replaced, along with idle speed control valve (which buzzes as normal, oh, should the arrow on the ISV point to the manifold brass pipe or the otherway??), all connections have been cleaned and are sound. I have done the timing and it is ok. OEM brand new plugs installed and ignition leads are good and all connected in the right order. New Bosch coil, and new ballast resistor. I removed and lubed all of the throttle linkage and the spring on the butterfly and visually confirmed that they are fully closed in rest position. Brass screws are fully in. I have done a hell of a lot to this car, its had a new frequency valve (from DMC) all the fuel lines are new right from the new fuel pump to the new filter. I took off the lines of the WUR and checked for blockages (none) and checked I had 19 ohms at the connector, so that appears to be good. There is fuel coming to the distributor, think I have good pressure but it hasn't been tested with a gauge. RPM relay is new, so is the cold start valve and the thermo time switch, (it also has a new waterpump) fuel tank is new and has only had new fuel in it. NOTE I have always had trouble starting cold, never warm! All other vaccum lines are also new! Idle switch is actuated but not too much.



Here are the things that I don't know. Why is Idle currently 2000 (approx an ants dick either way).

Firstly the car wont start unless I press the fuel flap ever so slightly down, or crank and crank it and it eventually fires, and I mean press it a mm down (the flap), any more and it boggs and dies. If i touch the accelerator it dies right away. When I set the timing (using a new gun) I pulled the vacuum advance off the distributor and plugged it, but it didn't seem to make any difference on or off, this was the case before and after I went into the VOD and replaced parts/hoses. So I don't know if my advance is buggered or if the vacuum solenoid is not getting power (should check that really now I say it out loud!!) I know my fuel mix is off too so I'm going to set it with my new dwell meter that is on its way to me, I timed it at its stupid high idle so that possibly needs doing again too once I get the idle down. Not sure if my O2 sensor works so I've had it unplugged, plugged it in earlier today and had idle hunting which I have never had before, is this a good sign or bad or none? I think my brass pipe it too loose causing a vacuum leak despite the o-ring being in ok condition but probably worn, but I've re seated it to see if it made a difference and no it didn't. (new o ring on the way)


So I'm at a loss, I try to get further but getting nowhere, cant get the idle anywhere near close to what it should be, and its drives like a bag of shit! Any advice you guys can help with before I'm found naked except for one red shoe wandering the local fields babbling to myself and drooling!

Mike

Jonathan
09-17-2016, 12:51 PM
The idle being right at 2,000 RPM points to the electrical connections between the thermistor (under the intake in the valley) and the idle ECU (the black one sitting on top) behind the driver's seat.

A test to see if that aspect is working is to unplug the white connector on the back of the ECU (the connector of the two on the passenger side of that black box). What you would normally see on our cars is for the idle to go immediately to 2,000 RPM and stay there.

Since your car is already doing that, it tells me either that connector isn't in properly, or perhaps, it is the connector at the thermistor itself (which is a pain because you can't reach it with the intake in place).

You said you replaced your thermistor, got any pictures of that spot after you replaced it and before you put the intake back on?

Check the connections on the back of that ECU and report back. Hang in there best you can. This sort of thing with our cars sucks, but we'll try and help you get it sorted out.

sdg3205
09-17-2016, 02:08 PM
Cold Starts: You don't say if you have verified thats your CSV is actually firing during a cold start - have you checked that? Let us know.

High Idle: - do you have access to another idle ECU you can swap in? That would rule out a bad idle ECU. Though rare, a bad ISM can damage an idle ECU. Have you verified the butterfly/plates are closing all the way? after delving into the VOD, the fit and alignment can change and the throttle linkage almost always need to be tweaked. Are you also hitting the idle microswitch at idle? once running, there is enough vacuum to cause the throttle to open just enough to prevent the switch from being engaged of the linkage is out of alignment.
You can test your ISM too by removing it, leaving the pin harness in tact, turning on power, and watching the valve rotate over the span of a few seconds.

Have you double checked for vacuum leaks?

Rough Idle/Pinging: Have you done a injector flow test? if not, do this, and re "crack" the injectors to set a baseline for adjusting the mixture.

Also, if it takes a while to warm up, that could be a WUR issue. Do you have gauges to test system pressures? perhaps a moot point until the fuel system has a baseline set.

Mrdashbo
09-17-2016, 03:27 PM
Thanks Fellas,


I will for sure check out the ECU and see what it tells me. I have only just installed brand new injectors from DMC so I doubt its that because I had this issue when the old injectors where in.

I can hear the idle motor spinning but I will unplug it to do a visual to be sure, wish I had access to a spare ECU but no dice. I have had some weird wiring gremlins early on in my endeavours so its a very good possibility.

The day I took off the meter unit i opened it up to check that the butterflies were closing completely. I haven't checked of the CSV is firing thats a good call I will do that tomorrow.

You are right its well worth cracking the injectors to see the flow never thought of that while I was in my dark rage haha, yes the microswitch is being contacted.
Stupidly I didn't get a picture of the damn valley but while I was there I did clean the contact for the thermistor and the other temp switch thingy.

Also on the ECU there is a black diode is this correct? its connected right next to a contact that comes out of the white plug??

Vacuum leaks i was sure there wasn't any but today I heard a hissing from the left side of the engine air rushing but could locate it, thought it was that brass pipe seal letting air in but want sure.

really appreciate the help thanks a million

sdg3205
09-17-2016, 03:35 PM
Thanks Fellas,


I will for sure check out the ECU and see what it tells me. I have only just installed brand new injectors from DMC so I doubt its that because I had this issue when the old injectors where in.

I can hear the idle motor spinning but I will unplug it to do a visual to be sure, wish I had access to a spare ECU but no dice. I have had some weird wiring gremlins early on in my endeavours so its a very good possibility.

The day I took off the meter unit i opened it up to check that the butterflies were closing completely. I haven't checked of the CSV is firing thats a good call I will do that tomorrow.

You are right its well worth cracking the injectors to see the flow never thought of that while I was in my dark rage haha, yes the microswitch is being contacted.
Stupidly I didn't get a picture of the damn valley but while I was there I did clean the contact for the thermistor and the other temp switch thingy.

Also on the ECU there is a black diode is this correct? its connected right next to a contact that comes out of the white plug??

Vacuum leaks i was sure there wasn't any but today I heard a hissing from the left side of the engine air rushing but could locate it, thought it was that brass pipe seal letting air in but want sure.

really appreciate the help thanks a million

Did you clean the gas tank REALLY well before using new injectors? new fuel filter? dirty fuel can ruin new injectors in just a few seconds.

Cracking the injectors - pull all 6, put in clear bottles, jump fuel pump, adjust mixture screw so that the injectors are JUST about to start spraying. Thats your baseline. Press metering plate to check spray patterns. Bad or no spray is either an injector or distributor issue.

If your CSV isn't spraying on a cold crank, check the 2 pin harness on the water pump switch - if it is seated BACKWARDS its possible the switch is now fried.

Vacuum leaks - that brass pipe is a killer. Use a flashlight in the dark (with air box removed) and shine the light from the LH side of the intake while pressing down the metering plate to see if you can see light. If you can, thats a leak. Also, did you follow the vacuum diagram when you were in the VOD? are the hoses off the y-pipe vacuum solenoid routed properly?

Mrdashbo
09-17-2016, 05:35 PM
Did you clean the gas tank REALLY well before using new injectors? new fuel filter? dirty fuel can ruin new injectors in just a few seconds.

Cracking the injectors - pull all 6, put in clear bottles, jump fuel pump, adjust mixture screw so that the injectors are JUST about to start spraying. Thats your baseline. Press metering plate to check spray patterns. Bad or no spray is either an injector or distributor issue.

If your CSV isn't spraying on a cold crank, check the 2 pin harness on the water pump switch - if it is seated BACKWARDS its possible the switch is now fried.

Vacuum leaks - that brass pipe is a killer. Use a flashlight in the dark (with air box removed) and shine the light from the LH side of the intake while pressing down the metering plate to see if you can see light. If you can, thats a leak. Also, did you follow the vacuum diagram when you were in the VOD? are the hoses off the y-pipe vacuum solenoid routed properly?

My Tank is brand new never had fuel in it until i put new fuel in recently, I have lots of glass jars so i will do the injector test in the morn, the more i think about it the more I'm convinced there is a leak on that goddam brass pipe. My thermotime is connected properly the connector will only fit in one way as its in good nick. Yeah vacuum pipes are the right way round I even labelled the when I installed them just incase a fucked it up! haha.

Brilliant idea on the shinning of the light on the brass tube I'm going outside to do that now!!

feel more positive now i have things to check and trace!

David T
09-17-2016, 11:01 PM
Do all the stuff suggested so far. I also agree the cold start valve should be checked because of the cold start problem. As for the lack of power I would check the duty cycle on the frequency valve. Make sure it gets into "closed loop".

Mrdashbo
09-22-2016, 05:08 PM
Hey Guys,

Have not had a chance to do anything til today as work has been mad, so here are my findings so far

1. Plug swap - starts first time then obviously dies when i unplug it.

2. Cold start valve is firing and fuel comes out fine.

3. The car wont start unless I jam something to press the fuel flap down a mm or so. (before doing baseline on injectors i may add)

4. Cracked the injectors, jumped the fuel pump, nice even spray pattern so I did what was suggested and set a baseline so fuel just about comes out.

5. Brass pipe o- ring and vacuum leaks all checked and seem to be fine.

6. Idle ecu when I unplug it the revs fly up and reduce when plugged back in. (but not to normal)

7. I hooked up my dwell meter and I can t get a reading to drop below 65 degrees (4 cylinder reading)

8. Brand new frequency valve does not buzz currently.

Car seems very hot small amount of steam/vapour coming from oil filler, but temp gauge is ready ok, then climbs (no doubt as its revving its tits off) after 5 mins of so called idling the engine was unbearably hot (cant remember if that right from my previous Delorean) the car runs like its under acceleration but the throttle is totally closed and the push road was disconnected so its not under any tension. Perhaps maybe its the WUR or something electrical have had issues with that yellow plug before, however I have replaced the metal contact inside with new. I do feel more positive like I'm getting somewhere but also come to a bit of a halt.

One question I do have is how to I know if my idle control valve has been put in the right way there is an arrow on it, but what way should it point?

Any ideas throw them at me I'm ready.

Cheers

Mike

Bitsyncmaster
09-22-2016, 06:00 PM
If your getting 65 deg for dwell and your FV is not buzzing, you probably don't have power on the FV. Make sure your lambda relay is the correct relay. The lambda relay is different from all the others.

I found it does not make much difference which way the idle motor is installed. But I think all of them have the connector closer to the rear bumper.

DMCMW Dave
09-22-2016, 06:07 PM
The arrow should point to the rear of the car (away from the brass tube).

Jonathan
09-23-2016, 09:11 AM
Something else you can do to eliminate potential problems while you try and figure things out, would be to disconnect the full throttle microswitch(s).

If you have an automatic trans car, you have two of these switches. If your car is a manual, you have just one switch. You will also hear them called WOT (wide open throttle) switches. Or the "kickdown" microswitch, or the "fuel enrichment" microswitch.

When you floor the gas pedal, the throttle spool is supposed to rotate all the way and push the tab on these switches to give you a) more fuel momentarily and b) drop you down a gear (on the automatic). Disconnecting them won't hurt a thing while you're troubleshooting, yet if one of those switches is shorted, it could be contributing to the high idle or enriched fuel condition.

The connection for the switches are the on the top of the engine, just behind the W pipe. Right out in plain sight. They look like little Tetris pieces.

46348

DMC5180
09-23-2016, 10:39 AM
You've got a lot of things going on here, perhaps we should focus on one Item at a time.

COLD START: You did the plug swap and said the engine fired right up, That verifies the the CSV functions when supplied with new circuit (+12 and Ground).

With the plugs back in the normal position, install a jumper between the Blue/Black and Black wire in the EMPTY white (hot start) relay socket in the back of the relay compartment. This will provide a TTS by-pass Ground for the CS circuit. Now try to Start the engine. If it fires right up, you've proven the CSV is seeing +12 while cranking and the ground side Terminal connection in the Blue connector is GOOD. If it does not start up then either of this items could be suspect. Assuming a GOOD TEST result, REMOVE the JUMPER, and focus on the TTS. As SG Dave suggested, check the plug orientation. Also do an Ohms test on the TTS pins to the block. I don't recall what the readings should be but someone will jump in with those I'm sure. They have been stated many times in various other threads. You said, you replaced the TTS, was this a JUST BECAUSE thing or was the old one actually bad? You may want to reinstall it if you still have it. (Assuming it was good) Do the OHMs test to that one also.


High Idle suggestion, pull the connector off the ISM the next time you have it running and report the results.

Mrdashbo
09-24-2016, 11:01 AM
Ok

I did the jumper in the hot start relay, did not make any difference, I can't get a reading on the tts and I've noticed the female connector on the tts is loose and looks like it's coming away from the main body of the switch.

I got it running eventually and while it was idling unplugged the ISV and it made no difference although it buzzes on key position 2?

Looking like it's a new tts for me, again! I removed the old one because it was a dud Also this one is only a few months old and the car hasn't really run. It's a new connector so it cannot be plugged in the wrong way.


The idle situation I'm stumped at I've got it a bit lower by adjusting the linkage as it was not quite contacting the switch but it's still just under 2000

And on .....

Bitsyncmaster
09-24-2016, 02:59 PM
Ok

I did the jumper in the hot start relay, did not make any difference, I can't get a reading on the tts and I've noticed the female connector on the tts is loose and looks like it's coming away from the main body of the switch.

I got it running eventually and while it was idling unplugged the ISV and it made no difference although it buzzes on key position 2?

Looking like it's a new tts for me, again! I removed the old one because it was a dud Also this one is only a few months old and the car hasn't really run. It's a new connector so it cannot be plugged in the wrong way.


The idle situation I'm stumped at I've got it a bit lower by adjusting the linkage as it was not quite contacting the switch but it's still just under 2000

And on .....

If the jumper in the hot start relay did not get it started but it does start doing the plug swap, you must have a bad connection in the bulkhead connectors. Otherwise I would suggest you get my hot start relay other than another TTS.

DMC5180
09-24-2016, 03:33 PM
Ok

I did the jumper in the hot start relay, did not make any difference, I can't get a reading on the tts and I've noticed the female connector on the tts is loose and looks like it's coming away from the main body of the switch.

I got it running eventually and while it was idling unplugged the ISV and it made no difference although it buzzes on key position 2?

Looking like it's a new tts for me, again! I removed the old one because it was a dud Also this one is only a few months old and the car hasn't really run. It's a new connector so it cannot be plugged in the wrong way.


The idle situation I'm stumped at I've got it a bit lower by adjusting the linkage as it was not quite contacting the switch but it's still just under 2000

And on .....

ISV aka ISM (idle speed motor). Is supposed to buzz with key in position 2 (RUN)

Jumping the Hot start socket should have provided a direct GROUND for the CSV circuit assuming you have +12V feeding the CSV while Cranking. Break out the Multi-meter start checking Harness continuity. Use Audible setting.

With the Hot start jumper in place, Remove the Blue CSV connector and Unplug TTS ) Hold CSV connector with terminals looking like this [ T T ] the LH terminal should show continuity to a chassis Ground (engine Intake) if NOTHING Back probe or remove bulkhead connectors Note: If you remove the BH connectors look for pins that may be dislodged (pushed Back)

The +12 power source for the CSV is the Same as the Starter Solenoid.

Test between the (doubled) WHITE/red wire in the White 7-way Bulkhead connector and the Blue CSV connector then to the TTS connector.

Test between the BLUE/ black wire in the White 9-way connector and the Blue CSV connector then check the TTS connector.

Mrdashbo
09-29-2016, 04:19 PM
Hello All,

Update time:

Ok, after a lot of great advice from you guys, i started tracing wiring, checking relays, and generally poking around.

Heres what happened, the car now starts first time on the key, I went around every offending connector and cleaned them, including a rather oxidised looking lambda connector (behind the drivers seat) I replaced the lambda relay with a new one from DMC and now I have a good start even when left for a few days.

Phew!

The idle situation seems to be improving, my idle (according to the gauge, which I'm unsure of its accuracy) sits at a hair below 1500, again I cleaned the switch connectors swapped out the microswitch for a spare I have and its improved a lot. I Hooked up my dwell meter to the + coil and - to ground and I have a steady 50 degrees.

i plugged in my O2 sensor and it hunted for a bit then after a while settled, I notice the frequency valve buzzes just off idle but not when idling normally. I still have a few adjustments to make on the throttle linkage as I has some play in it and the microswitch is a bit too far closed, but I seem to not quite be able to get any lower.

It doesn't sound as fast as before so ill test the RPM with a meter before choosing to believe the gauge, or buggering about further.

I think I must have a vac leak somewhere around the brass pipe as i can hear an air rushing sound from that area, so I'm going to dig around in that when I get another few hours. Its still a bit shaky the engine when idle but it may need a good run as I'm sure the cat is full of crap by now and i have a loose clamp on the exhaust so that prob won't help.


Oh just to add during idle if i press my full throttle switch nothing happens? is this normal???

Anyone have any more ideas on what maybe causing it not to fall anymore? feel so close but not quite there.

Mike

Bitsyncmaster
09-29-2016, 05:40 PM
Try hooking your dwell up to the FV or use the orange wire from the lambda dwell output. You probably need to adjust your mixture.

FABombjoy
09-29-2016, 06:10 PM
If you have a vacuum leak the lambda controller may already be maxing out your mixture, hence the lack of change when pushing the WOT switch. You can confirm by using the kjet dwell test Dave mentions above.

Fix all vacuum leaks before making any adjustments or you'll just be re-readjusting things again.

Mrdashbo
10-05-2016, 04:04 PM
Went back to my car the other day, turned the key and all of the crappy problems I had thought I'd solved were back, which makes me think I have fuel pressure problems?

So I bought a pressure testing kit hooked my gauge up to the larger input on the WUR (through the banjo so just tapping into the system) and it struggled to get up to 30 PSI (fuel pump jumped) the engine was like a crappy washing machine jumping all over the place then died.


Two questions: 1. Am I connecting the gauge up to the right port? 2. What the hell could be causing such low pressure? my pump, accumulator, filter and tank, and lines were all brand new. Could it be the check valve in the pump? or the WUR, meter head?


thoughts?

Bitsyncmaster
10-05-2016, 04:28 PM
Went back to my car the other day, turned the key and all of the crappy problems I had thought I'd solved were back, which makes me think I have fuel pressure problems?

So I bought a pressure testing kit hooked my gauge up to the larger input on the WUR (through the banjo so just tapping into the system) and it struggled to get up to 30 PSI (fuel pump jumped) the engine was like a crappy washing machine jumping all over the place then died.


Two questions: 1. Am I connecting the gauge up to the right port? 2. What the hell could be causing such low pressure? my pump, accumulator, filter and tank, and lines were all brand new. Could it be the check valve in the pump? or the WUR, meter head?


thoughts?

You do two pressure tests.

1) Primary pressure is tested without the engine running and the test set hose valve shut, RPM relay jumpered. You should get 70 to 75 PSI.

2) With engine running and test set hose valve open. Pressure starts out low with cold engine 10 to 20 PSI and quickly gets up to 50 PSI when engine warms up.

Mrdashbo
10-05-2016, 05:09 PM
You do two pressure tests.

1) Primary pressure is tested without the engine running and the test set hose valve shut, RPM relay jumpered. You should get 70 to 75 PSI.

2) With engine running and test set hose valve open. Pressure starts out low with cold engine 10 to 20 PSI and quickly gets up to 50 PSI when engine warms up.

Sorry to sound thick, but what do you mean by hose valve open/closed
my gauge has many attachments but the one i currently have hooked up is a straight from gauge to the banjo on the WUR

Bitsyncmaster
10-05-2016, 05:30 PM
Sorry to sound thick, but what do you mean by hose valve open/closed
my gauge has many attachments but the one i currently have hooked up is a straight from gauge to the banjo on the WUR

To read primary pressure you shut off the feed going to the WUR. So the test setup should have a shutoff valve to measure primary pressure.

If you can somehow plug that line going to the WUR, you could still use your gauge to read primary pressure.

Mrdashbo
10-07-2016, 12:48 PM
You do two pressure tests.

1) Primary pressure is tested without the engine running and the test set hose valve shut, RPM relay jumpered. You should get 70 to 75 PSI.

2) With engine running and test set hose valve open. Pressure starts out low with cold engine 10 to 20 PSI and quickly gets up to 50 PSI when engine warms up.


Did the primary pressure test first time got about 40psi and it was very slow getting there, but I tightened the connections on the pressure tester and did it again and I got around 65 psi. But it wouldn't reach 70

I also tested direct off the feed line off the filter too and the pressure was over 90 psi? Car still runs like a bag of shit and won't start unless I press the air flap. So I think that points to my WUR? Or meter head?

David T
10-07-2016, 02:51 PM
Sounds like you may need a mixture adjustment and/or fix a bunch of vacuum leaks. By pressing down the air sensor plate you are making the A/F mixture richer (adding more fuel to the air). Means the motor is running too lean, either because the mixture is off (not likely unless it has already been messed with) or (more likely) you have a lot of vacuum leaks. Also the frequency valve must buzz. That adds fuel to the mixture to get the A/F ratio just right. Without it buzzing the motor will be running lean and have no power. Is there a plug over the mixture screw?

Bitsyncmaster
10-07-2016, 02:52 PM
Did the primary pressure test first time got about 40psi and it was very slow getting there, but I tightened the connections on the pressure tester and did it again and I got around 65 psi. But it wouldn't reach 70

I also tested direct off the feed line off the filter too and the pressure was over 90 psi? Car still runs like a bag of shit and won't start unless I press the air flap. So I think that points to my WUR? Or meter head?

Primary pressure should peak in two seconds. 65 psi will probably not hurt engine operation as long as mixture is set.

Your WUR usually does not affect engine starting. Control pressure should settle out around 50 PSI after engine has warmed up.

Mrdashbo
10-07-2016, 03:48 PM
Primary pressure should peak in two seconds. 65 psi will probably not hurt engine operation as long as mixture is set.

Your WUR usually does not affect engine starting. Control pressure should settle out around 50 PSI after engine has warmed up.

Ok so am I looking at a blockage somewhere in the meter head or lines? My primary pressure literally took a minute to get to 65?

David T
10-07-2016, 04:06 PM
Ok so am I looking at a blockage somewhere in the meter head or lines? My primary pressure literally took a minute to get to 65?

It can take a while for the primary pressure to get up to spec especially from 0 because you must pressurize the accumulator. That's OK because the cold start valve doesn't need full pressure to get the motor started. The motor (when cold) starts on the cold start valve and by the time it has used up that fuel the injectors should be squirting. Easy to check, pull an injector and watch. you should also feel back-pressure when you push down on the air sensor plate.

Mrdashbo
10-07-2016, 04:54 PM
It can take a while for the primary pressure to get up to spec especially from 0 because you must pressurize the accumulator. That's OK because the cold start valve doesn't need full pressure to get the motor started. The motor (when cold) starts on the cold start valve and by the time it has used up that fuel the injectors should be squirting. Easy to check, pull an injector and watch. you should also feel back-pressure when you push down on the air sensor plate.



Yeah I get pressure on the plate and the injectors are spraying,
Just a bit puzzled at why the engine takes so long to fire up and it's very jumpy and splutters. Then dies I have to press the air flap to get it started. V weird

Frequency valve I can feel sputtery fuel in the hose

I know I'm still basing electrical gremlins too so can't rule that out

Bitsyncmaster
10-07-2016, 06:00 PM
Ok so am I looking at a blockage somewhere in the meter head or lines? My primary pressure literally took a minute to get to 65?

First check your voltage right on the pump and verify you get close to 12 volts. My guess is your pump is bad but if your accumulator had a bad leak that could be a problem.

David T
10-07-2016, 09:04 PM
Hard to start and "jumpy" could be that although the injectors are spraying, if they have bad patterns the fuel won't atomize properly and the motor won't run smoothly.

Mrdashbo
10-08-2016, 11:55 AM
Did some more checking this afternoon. The primary pressure test took 3 mins to reach 60psi and went no further
I have 12v at the pump but looking into the tank it's not pulling or returning really fast. Bear in mind i don't have an original baffle mine is more like specialtauto type.

Pump is also quite noisy, but when I put the pressure tester direct on the feed line the pressure was tremendous

I'm suspecting as you did it's a bad pump, but the pressure amomolies are convincing me it's something engine side as my pump is only about 2 years old and the car has hardly moved. I know some can just be bad.

The journey continues ...

Bitsyncmaster
10-08-2016, 01:55 PM
I have seen one fuel filter completely plugged. That could also be the problem.

Mrdashbo
10-08-2016, 04:51 PM
I will check it out , although i thinks its unlikely as its new and only has new fuel through it, I'm going to replace the pump and see what happens i also have spare accumulator incase thats the culprit, but the car is starting now but seconds later its dies seems like a fuel starvation and if the pumps on the fritz that makes sense


if anyone has any other ideas lemme know

cheers

DMC5180
10-08-2016, 06:29 PM
If it starts then dies, it's likely just running on the burst of cold start fuel.


Sent from my iPhone using Tapatalk

Horsebox
10-08-2016, 07:05 PM
Do you have 12V across the fuel pump whilst it is running?

It's easy to see 12V at the positive terminal of the pump under no load but it's what happens when the pump is running that matters.

Horsebox
10-08-2016, 07:26 PM
Before splashing the cash on a new fuel pump it would be worth running a long wire directly from the fuel pump negative terminal to the battery negative terminal. And see if the engine runs that way. This will bypass all of the stock harness connections back to the battery.

Mrdashbo
10-09-2016, 04:05 AM
Before splashing the cash on a new fuel pump it would be worth running a long wire directly from the fuel pump negative terminal to the battery negative terminal. And see if the engine runs that way. This will bypass all of the stock harness connections back to the battery.

I jumpered the fuel pump relay and it has 12v for sure but I'll try running a wire and start her up as suggested

I will report back

Bitsyncmaster
10-09-2016, 06:51 AM
If you just measure the voltage across the two pump terminals you will know if there is a bad connection on either side of the circuit. It is pretty typical you drop one volt or more over the wiring since the pump draws about 7 amps.

Mrdashbo
10-09-2016, 11:29 AM
Late last night (to rule it out)I took off the fuel meter head and cleaned it out with carb cleaner it looked pretty good the piston was very clean and not stuck it moved very freely so that's one less thing.

Going to do a measurement on the pump voltage shortly then I may try and put a new one way valve before the pump to see if the one inside has gone bad


Just out of interest what would cause a significant voltage drop on the pump itself?

To be continued ..

Horsebox
10-09-2016, 03:44 PM
Just out of interest what would cause a significant voltage drop on the pump itself?


Crappy connectors. They were crappy 35 years ago and time hasn't done them any favours. For the fuel pump circuit they are all easily accessible for a good clean except the washer bottle area connectors that probably haven't been touched since the car left Dunmurry. Those connectors do both the + and -. Hence my suggestion to eliminate the negative side by going directly from pump negative to battery negative and see if it runs OK that way. That would prove a wiring problem rather than replacing a perfectly good pump.

Every electrical problem I've had with my car has been down to the connections. After running problems I managed to claw back 2V across the pump by cleaning everything, and re grounding the pump.

I believe Bitsyncmaster has managed to get full primary pressure from just 8V across the pump, so maybe this isn't your problem. It's an easy/cheap test tho...

Good luck!

Horsebox
10-09-2016, 05:05 PM
Ok so am I looking at a blockage somewhere in the meter head or lines? My primary pressure literally took a minute to get to 65?

Are you sure you're measuring the pressures correctly?

The pressure testing kit you just got hold of should have a built in valve. With the valve open you measure control pressure. With it closed you measure primary pressure. The engine won't run in this second config so you do the test with the engine off and RPM relay jumpered to force the fuel pump to run.

If your kit doesn't have a valve, all you will ever measure is control pressure, which will start low and increase to a maximum after a few minutes.

As someone else said, you have many things going on with your engine by the sounds of it. All of which will have a simple fix, but diagnosis will be hard trying to unpick them all from each other. You will have that eureaka moment tho!

Bitsyncmaster
10-09-2016, 05:25 PM
Crappy connectors. They were crappy 35 years ago and time hasn't done them any favours. For the fuel pump circuit they are all easily accessible for a good clean except the washer bottle area connectors that probably haven't been touched since the car left Dunmurry. Those connectors do both the + and -. Hence my suggestion to eliminate the negative side by going directly from pump negative to battery negative and see if it runs OK that way. That would prove a wiring problem rather than replacing a perfectly good pump.

Every electrical problem I've had with my car has been down to the connections. After running problems I managed to claw back 2V across the pump by cleaning everything, and re grounding the pump.

I believe Bitsyncmaster has managed to get full primary pressure from just 8V across the pump, so maybe this isn't your problem. It's an easy/cheap test tho...

Good luck!

+1

The round connector pins are crappy and loose their tension if overheated.

I'm surprised you remember an old thread where I did test the pump working down to 8 volts. That's not saying they all will work that low.

David T
10-09-2016, 05:50 PM
+1

The round connector pins are crappy and loose their tension if overheated.

I'm surprised you remember an old thread where I did test the pump working down to 8 volts. That's not saying they all will work that low.

IMHO you are going off on a tangent. If you can get the injectors to spray and the motor runs, you probably have enough primary pressure. I would forget the pump for now and concentrate on why the motor is running badly. Verify the frequency valve is buzzing and you have no vacuum leaks. Rough set the mixture and then try doing it watching a dwell meter. Verify the idle system is working.

Bitsyncmaster
10-09-2016, 07:39 PM
IMHO you are going off on a tangent. If you can get the injectors to spray and the motor runs, you probably have enough primary pressure. I would forget the pump for now and concentrate on why the motor is running badly. Verify the frequency valve is buzzing and you have no vacuum leaks. Rough set the mixture and then try doing it watching a dwell meter. Verify the idle system is working.

But there is a problem with his pump taking 2 min to come up to pressure. It's best to start with fuel pressures and get the first things bad fixed first.

David T
10-09-2016, 09:18 PM
But there is a problem with his pump taking 2 min to come up to pressure. It's best to start with fuel pressures and get the first things bad fixed first.

While it is a problem it takes a while to get up to full pressure, that is not why the motor is running badly when it is running. Things that can cause it to take a while to build up pressure:
Bad pump
Bad connections to pump
Dirty fuel filter on pick-up
Kinked pick-up hose (old style baffle system)
Stuck open PPR
Should be able to check most of these things quickly and find the problem but it won't get the motor running any better.

Bitsyncmaster
10-10-2016, 06:30 AM
While it is a problem it takes a while to get up to full pressure, that is not why the motor is running badly when it is running. Things that can cause it to take a while to build up pressure:
Bad pump
Bad connections to pump
Dirty fuel filter on pick-up
Kinked pick-up hose (old style baffle system)
Stuck open PPR
Should be able to check most of these things quickly and find the problem but it won't get the motor running any better.

I have tested it takes less than two seconds with zero rest pressure and the OEM (large) accumulator to pump up to full primary pressure. If it takes 2 min. then there will be problems even if the engine starts.

Mrdashbo
10-10-2016, 10:51 AM
I have tested it takes less than two seconds with zero rest pressure and the OEM (large) accumulator to pump up to full primary pressure. If it takes 2 min. then there will be problems even if the engine starts.

Think I'm going to need to get it to at least start up and run before i can check any issues with poor running, I did notice the b@stard brass pipe o-ring and keeper had come completely loose so yesterday I installed a new one and that is all tight again, this could be the rough running culprit as obviously its a huge vacuum leak. I've checked the PPR, and the pump screen and pickup hose no problems there so its either connection, or crappy pump. ill get my head under the washer bottle area and look at that connections, grounds then work back from there. Although with the RPM relay jumped the pump did have just over 12v to it (tested from the harness connector not direct to the pump, as those rubbers are damn near like plastic now, can't get them off)

Worse case scenario is I have a spare pump. But I do hate not knowing what the problem is, to be fair if I think back I've always had a fuel delivery issue of some kind intermittanlty, at least this way its a good education into areas of the fuel system I wasn't familiar with. You guys are a wealth of knowledge thanks again, I will report back.

Mike

Mrdashbo
10-21-2016, 08:09 PM
Think I'm going to need to get it to at least start up and run before i can check any issues with poor running, I did notice the b@stard brass pipe o-ring and keeper had come completely loose so yesterday I installed a new one and that is all tight again, this could be the rough running culprit as obviously its a huge vacuum leak. I've checked the PPR, and the pump screen and pickup hose no problems there so its either connection, or crappy pump. ill get my head under the washer bottle area and look at that connections, grounds then work back from there. Although with the RPM relay jumped the pump did have just over 12v to it (tested from the harness connector not direct to the pump, as those rubbers are damn near like plastic now, can't get them off)

Worse case scenario is I have a spare pump. But I do hate not knowing what the problem is, to be fair if I think back I've always had a fuel delivery issue of some kind intermittanlty, at least this way its a good education into areas of the fuel system I wasn't familiar with. You guys are a wealth of knowledge thanks again, I will report back.

Mike

Hey guys

Sorry it's been so long but work, plus kids, plus rain, you get the idea!


I managed to borrow another fuel pump so I could rule it out and surprise surprise installing the known good pump did nothing. The car is definitely not getting enough fuel as it starts for 2 seconds on the CSV and dies, I'm once again stumped. Could this be an accumulator related issue?

Can anyone throw any light on this? Not sure where to check next

Thanks

Mike

DMC5180
10-21-2016, 08:32 PM
You would have to have a really bad accumulator diaphragm allowing fuel to by-pass and return to the tank. You could pinch off the spring chamber return hose with vise-grips to see if that made a difference before replacing parts.


Sent from my iPhone using Tapatalk

Bitsyncmaster
10-21-2016, 08:46 PM
If the accumulator is original, go ahead and replace it. I'd be surprised if any original accumulator is still good.

David T
10-21-2016, 10:14 PM
Even with a totally bad accumulator you would not see this symptom. If you can't get enough primary pressure some of the possibilities include:

Dirty tank and pick-up filter
Collapsing pick-up hose
Plugged up fuel filter
Stuck open PPR
Kinked, bent collapsed fuel line

At this point the thing to do is to bypass the fuel pump to run without the motor running and measure the Primary Pressure. If you don't have full pressure you have to figure out why. Is it possible you mixed up the feed and return lines at the fuel pump?

rtcraver
10-23-2016, 10:17 AM
this may sound dumb, but....
Check to see if both sides of the engine are heating up. I had an issue with backfiring, no power etc, and it turned out the guy who redid the engine did not set the distributor on cyl. 1 at TDC. Only 3 cylinders were firing, one side only....

Just sayin'

Mrdashbo
10-23-2016, 06:25 PM
The thing I can't get my head around is when I take off the feed line from the meter head and attach my pressure gauge, it reads 90 psi within seconds, then when I check the primary pressure in the correct way my pressure is practically non existent until a min or two then it's lucky if it reaches 50 psi,

As I said before my tank was brand new with only new fuel in it and the filter is new too.

Both sides of engine are stinking hot as normal. I'm going to replace and check the accumulator and lines as it may be a source to rule out. But before I'll check the pump hoses are correct way round.

Just can't make out the logic of this issue as it happened out of nowhere

Bitsyncmaster
10-23-2016, 08:02 PM
90 PSI from the pump is good. The primary pressure regulator inside the fuel distributor is what sets the primary pressure. Have you replaced the O-ring in the PPR yet?

David T
10-23-2016, 10:16 PM
You MUST use the pressure gauge set-up and connect it as per the manual. If you just disconnect the hose and hook a meter onto it you are not checking the PPR and the return line. Not doing it correctly you only measuring static pressure and not flow.

DMC5180
10-23-2016, 10:20 PM
The thing I can't get my head around is when I take off the feed line from the meter head and attach my pressure gauge, it reads 90 psi within seconds, then when I check the primary pressure in the correct way my pressure is practically non existent until a min or two then it's lucky if it reaches 50 psi,

As I said before my tank was brand new with only new fuel in it and the filter is new too.

Both sides of engine are stinking hot as normal. I'm going to replace and check the accumulator and lines as it may be a source to rule out. But before I'll check the pump hoses are correct way round.

Just can't make out the logic of this issue as it happened out of nowhere

Based on info you just stated. That pretty much rules out anything in the tank. It would also prove you don't have lines crossed at the tank either. If you did, you wouldn't have any pressure at the main feed line. The couple seconds to hit 90 with Deadhead pressure is normal and also verifies the accumulator isn't shot. In fact you should do this test again , kill power to the pump and see how long it will hold 90 and see how long it takes to bleed off pressure.

Aside from doing the above test, I'd say you've isolated it to a fuel distributor issue. PPR O-rings ??? Or other internal problem.



Sent from my iPhone using Tapatalk

David T
10-24-2016, 11:47 AM
Based on info you just stated. That pretty much rules out anything in the tank. It would also prove you don't have lines crossed at the tank either. If you did, you wouldn't have any pressure at the main feed line. The couple seconds to hit 90 with Deadhead pressure is normal and also verifies the accumulator isn't shot. In fact you should do this test again , kill power to the pump and see how long it will hold 90 and see how long it takes to bleed off pressure.

Aside from doing the above test, I'd say you've isolated it to a fuel distributor issue. PPR O-rings ??? Or other internal problem.



Sent from my iPhone using Tapatalk

I respectfully disagree. Without a good flow you can't know if a filter is plugged up, a hose or pipe kinked. It is possible he is on the return hose and the accumulator is bad and he is seeing pressure. With so many things going on here you can't assume anything is right. Since he is not using the proper gauge set-up we can't assume he is connecting to the feed hose. This test he just did only proves the fuel pump runs and can provide pressure.

Mrdashbo
10-25-2016, 07:33 PM
I respectfully disagree. Without a good flow you can't know if a filter is plugged up, a hose or pipe kinked. It is possible he is on the return hose and the accumulator is bad and he is seeing pressure. With so many things going on here you can't assume anything is right. Since he is not using the proper gauge set-up we can't assume he is connecting to the feed hose. This test he just did only proves the fuel pump runs and can provide pressure.

Just to clarify I have used the correct pressure tester set up for checking primary pressure this gave me 40-60 psi max
As a matter of course I checked the pump pressure direct off the feed line to see the result I got. Once I get a bit more time this weekend I'll check the PPR and check for linked lines etc

David T
10-25-2016, 09:39 PM
Just to clarify I have used the correct pressure tester set up for checking primary pressure this gave me 40-60 psi max
As a matter of course I checked the pump pressure direct off the feed line to see the result I got. Once I get a bit more time this weekend I'll check the PPR and check for linked lines etc

Using the correct test set-up you test flow and pressure. I suggest you go back into the tank and check everything again. Look for dirt that can plug up the pick-up filter, a soft pick-up hose that may be collapsing or kinking, verify you have the pump output connected to the feed hose. Check the filter, if you don't hook it up correctly you can block the flow of fuel. Do you have the original fuel tank set-up or are you using the combo filter? Recheck that you are hooking up the fuel gauge correctly and you are measuring Primary pressure not control pressure. If, after all this you can't get enough Primary pressure, and you have no leaks, either the PPR is leaking or set too low or the fuel pump is no good.

Bitsyncmaster
10-26-2016, 06:17 AM
Using the correct test set-up you test flow and pressure. I suggest you go back into the tank and check everything again. Look for dirt that can plug up the pick-up filter, a soft pick-up hose that may be collapsing or kinking, verify you have the pump output connected to the feed hose. Check the filter, if you don't hook it up correctly you can block the flow of fuel. Do you have the original fuel tank set-up or are you using the combo filter? Recheck that you are hooking up the fuel gauge correctly and you are measuring Primary pressure not control pressure. If, after all this you can't get enough Primary pressure, and you have no leaks, either the PPR is leaking or set too low or the fuel pump is no good.

You cannot check pump flow rate via pressure testing. The OP got 90 PSI quickly testing the "dead ended" pump pressure which sounds good to me. That suggests his tank internals are good.

David T
10-26-2016, 08:28 PM
You cannot check pump flow rate via pressure testing. The OP got 90 PSI quickly testing the "dead ended" pump pressure which sounds good to me. That suggests his tank internals are good.

"Suggests". Under high flow rates if you are pulling the fuel through a kinked pick-up hose or a partially plugged up filter, the flow would drop off and you would lose pressure. In my experience many of the fuel system problems begin in the fuel tank. You have to start somewhere. While he did say he did a lot of things maybe he did something incorrectly and by looking at it again he may see the problem. Hard to see anything wrong from here!

Mrdashbo
10-29-2016, 04:58 AM
Update

I replaced the PPR o-ring and added a Shim to see if the pressure would increase, my fuel flap has a good resistance that it hasn't had before and the pressure gauge climbs up much faster but it reaches only 55-60 then slows down to almost a non exhaustant climb. Car won't start still and strangely it has a hiss after it dies, not sure if hat is significant or not.

It is 100% nothing on the tank as i have now replaced all components in there to check if I had an a bad component or problem with the setup.


Can't believe this problem is still evading me feel like I'm missing something but don't know what

Double pffffffff

DMC5180
10-29-2016, 09:36 AM
Are you saying it won't start on CS fuel either? If that's the case check for spark again. May something got dislodged while working on things.

If you can post a video of your pressure testing that would be great.

Sent from my iPhone using Tapatalk

Bitsyncmaster
10-29-2016, 10:29 AM
Update

I replaced the PPR o-ring and added a Shim to see if the pressure would increase, my fuel flap has a good resistance that it hasn't had before and the pressure gauge climbs up much faster but it reaches only 55-60 then slows down to almost a non exhaustant climb. Car won't start still and strangely it has a hiss after it dies, not sure if hat is significant or not.

It is 100% nothing on the tank as i have now replaced all components in there to check if I had an a bad component or problem with the setup.


Can't believe this problem is still evading me feel like I'm missing something but don't know what

Double pffffffff

I thought I replied to this thread this morning but I don't see it now.

I'm still thinking your PPR is at fault. It takes about 0.040" of shim to up your PPR pressure 5 PSI. Maybe your PPR is missing OEM shims or the spring was changed by a PO.

Mrdashbo
10-29-2016, 10:55 AM
I thought I replied to this thread this morning but I don't see it now.

I'm still thinking your PPR is at fault. It takes about 0.040" of shim to up your PPR pressure 5 PSI. Maybe your PPR is missing OEM shims or the spring was changed by a PO.

It does fire and run on the CS but then immediately dies

It had only one shim in there so I bought from Dmc club three shims I put the middle thickness one in there can't remember the mm off the top of my head but maybe I should increase it with the thicker shim also and see the results? It did make a difference but you could be right it seems like the only feesable area of intestrest

I will add a shim and see what we get, the saga continues ...

David T
10-29-2016, 01:52 PM
It is also possible one of the "O" rings in the PPR is damaged. That would prevent you form building up sufficient pressure. The "O" rings usually are never damaged unless the PPR was taken apart at some point in the past. If you do take the PPR apart best to have a new set of "O" rings to put in on hand. It must be done carefully with a lot of lubrication. They are not ordinary size "O" rings that you can get locally. Order them from a vendor. Special T has them.

Mrdashbo
11-05-2016, 12:34 PM
Hey guys got an update for ya.

I added two shims to the PPR and replaced both o-rings this gave me a primary pressure reading of 65psi
Then my coil died due to water ingress, so I replaced it and still no difference I noticed if I kept the key on Position 3 it would keep running. Then I did the plug swap and it started and ran (like a bag of shit) but it ran yaaaaay!!!

I noticed the cat was smoking like crazy from the joint to the exhaust presumably with all the cranking and fuel it has clogged up the cat which will need to be replaced?

So if it starts from the plug swap what does that mean, as I have checked the CSV and I was firing fuel out before hand? But my thermotime is a bit wobbly (literally the connector moves) Is the cat smoking an issue or just as I suspect?

Was great to hear her run again never thought it would, but not out the woods yet

Cheers

Bitsyncmaster
11-05-2016, 01:56 PM
I would not worry about the CAT yet. Get the mixture adjusted and see if that makes it start better. A plugged CAT would make the dwell reading swing to extremes (can't set the mixture).

How does it run when warmed up?

Mrdashbo
11-05-2016, 04:33 PM
I would not worry about the CAT yet. Get the mixture adjusted and see if that makes it start better. A plugged CAT would make the dwell reading swing to extremes (can't set the mixture).

How does it run when warmed up?



Never got that far to get it warm revved it a bit it sounded good. but was worried about the cat smoking and didn't want to run it with the plug swapped it basically died when I unplugged it

Should I run it warm to see with the plug swap and get a reading? Plus during running my pressure gauge read about 40-50?

DMC5180
11-05-2016, 05:46 PM
No, running with the plug swap will flood the engine (run like crap) under normal circumstances. Your fuel distributor may be so far out of adjustment, it just won't run without the CSV fuel at the moment though.

You should pull all the injectors , put them in jars and see set the CO screw to spray fuel (fuel pump jumped to run)
Then back off the screw till fuel stops spaying from the injectors. This is a good starting point. Reinstall all injectors and see if it will stay running.


Sent from my iPhone using Tapatalk

David T
11-05-2016, 06:08 PM
No, running with the plug swap will flood the engine (run like crap) under normal circumstances. Your fuel distributor may be so far out of adjustment, it just won't run without the CSV fuel at the moment though.

You should pull all the injectors , put them in jars and see set the CO screw to spray fuel (fuel pump jumped to run)
Then back off the screw till fuel stops spaying from the injectors. This is a good starting point. Reinstall all injectors and see if it will stay running.


Sent from my iPhone using Tapatalk

Seconding the DO NOT RUN LONG with the plug swap. It will run very rich and the CAT will start to glow red. If it starts and runs on the plug swap it means the ignition system and basic mechanicals of the motor are OK. Your problem now is to get the fuel injectors to work. They could be plugged up, the pressure is too low, or the mixture is way off.

Mrdashbo
11-06-2016, 04:48 AM
Seconding the DO NOT RUN LONG with the plug swap. It will run very rich and the CAT will start to glow red. If it starts and runs on the plug swap it means the ignition system and basic mechanicals of the motor are OK. Your problem now is to get the fuel injectors to work. They could be plugged up, the pressure is too low, or the mixture is way off.

Should the injectors spray fuel only when the flap is pressed or should they spray when idle? Will try it today injectors are new so I assume it's mixture is wayoff and pressure issues

DMC5180
11-06-2016, 09:50 AM
Injectors will stop spraying at about 43 psi (rest pressure). The air plate (CO screw) should be adjusted so the injectors DO NOT SPRAY with air plate closed, but WILL SPRAY with slight down pressure applied to the plate. Under normal circumstances when the engine is idling steady the air plate will be down maybe 1/4" at the edge closest to you, the plate moves in an arc so the back edge gap will be greater than the front edge.


Sent from my iPhone using Tapatalk

Mrdashbo
11-13-2016, 12:32 PM
Managed to get an hour on the car this afternoon, pulled the injectors, no matter how far I turn the co screw they don't spray unless the plate is pressed down so I'm guessing the pressure is still not right. I get 65 primary pressure but when the engine is running it's only around 50.

So it's back to checking all the lines etc I do suspect at this point a bad accumulator or hose going into it as I have now checked every other thing. The garage at the bottom of my road lets me use their ramp from time to time. So that going to be my next goal.

Bizarrely it did start today with a lot of cranks but I'm sure it will not have very good acceleration but should make it.

Mrdashbo
12-01-2016, 04:23 PM
Ok so....

Weirdly it seems my issue is centred around the rpm relay or wiring I have two rpm relays both work intermittently not sure which one is bad, (need to test both properly) and my fuse 7 melted yesterday. But the car starts and runs fine now. I went out in it today, got to a Garage and it would not start, fiddled with the rpm relay and wiggled the new fuse in 7 and boom, of she went. I think a crappy relay or connection or poor earth?

So I'm going to be doing some investigating into this area. Has anyone else experienced any issues in the rpm, relay, wiring lambda fuse or that general region that could tip me off to what it could be?

But I can finally drive her and it felt great!!!!

DMC5180
12-01-2016, 05:05 PM
Melting fuse 7 is the most common issue with the delorean. Once resistance builds up at the fuse connection you can't just stick another fuse in it and expect it to last long. The terminals become weak and the wire near the terminal gets damaged from heat. The fix it is to do a replacement fuse box kit. The kit comes with high quality terminals. You also should replace any heat damaged wire near the box.

I think I replaced about a foot of wire for fuse 7 when I did my fuse box replacement 10 years ago. I've had zero problems at the fuses ever since.


Sent from my iPhone using Tapatalk

Bitsyncmaster
12-01-2016, 05:37 PM
The stock RPM relays will get broken solder joints where the relay inside is soldered to the circuit board. Happens a lot and is caused by the heating and cooling inside the unit. The stock RPM relays get very hot normally.

David T
12-01-2016, 09:39 PM
The stock RPM relays will get broken solder joints where the relay inside is soldered to the circuit board. Happens a lot and is caused by the heating and cooling inside the unit. The stock RPM relays get very hot normally.

If you melted fuse #7 you probably overheated the RPM relay. Often you can make it work again if you resolder the contacts. If you don't want to replace the whole fuseblock one way to fix it for a while is to remove the wires for fuse #7 from the fuseblock and wire in an in-line fuse. That circuit melts usually because of bad connections in the fuel pump circuit and a bad or dying fuel pump. Replacing the fuse and fixing the relay may get you going but to keep things from melting again you have to go over every connection to the fuel pump and replace the fuel pump.

Elvis
12-02-2016, 04:24 PM
overheated the rpm relay ? why ?

mechanical force is one of the main reasons why the contacts in the rpm relay
get loose.

Solder-joint is not meant to work with mechanical force !

heat and vibrations help to make it worse of course.

but - it lasted +30 years -> resolder it and it will be good for another car's life.