View Full Version : General Engine Dies while Driving
Jimmycxc
09-19-2016, 11:50 AM
So I ran into this a few months ago and very appreciative for everyone's help. My car died on the road and after troubleshooting all electrical, I ended up replacing my fuel pump, primed the lines, and she started right up. I drove around 300 miles and everything was fine. Last night, I went out for a little ride and as I'm pulling back into my neighborhood, the engine shuts off and will not restart. I pushed it back to my garage. This morning, I turn the key and it fires right up. Any ideas?
David T
09-19-2016, 12:26 PM
So I ran into this a few months ago and very appreciative for everyone's help. My car died on the road and after troubleshooting all electrical, I ended up replacing my fuel pump, primed the lines, and she started right up. I drove around 300 miles and everything was fine. Last night, I went out for a little ride and as I'm pulling back into my neighborhood, the engine shuts off and will not restart. I pushed it back to my garage. This morning, I turn the key and it fires right up. Any ideas?
When you have a trouble that comes and goes like that it is usually an electrical problem. Check the connections to the ballast resistor on the firewall. Next time it happens try to hear if the fuel pump is running.
burch
09-19-2016, 01:59 PM
Also check the fuel pump electrical connection. Depending on which pump solution you went with, the connectors can be a little iffy.
SS Spoiler
09-19-2016, 03:04 PM
I would lean toward the pick up coil in the distributor......
Drive Stainless
09-19-2016, 03:15 PM
I would lean toward the pick up coil in the distributor......
Seconded.
Morpheus
09-19-2016, 03:16 PM
I'm surprised nobody here has suggested RPM relay.
Elvis
09-19-2016, 04:36 PM
ignition coil and rpm relay :-)
sdg3205
09-19-2016, 05:20 PM
RPM relay is often all or nothing, but you could rule it out in a heart beat with a jumper.
Jimmycxc
09-19-2016, 06:28 PM
Sorry, I should have said what I already corrected from the last time it happened. Solid state rpm relay. Cleaned all grounds and ran a new ground for inertia switch. Cleaned rear ballast resistor connections. Exact replacement of fuel pump. I will have to do some research on the pickup coil. Thank you
AugustneverEnds
09-19-2016, 07:06 PM
How long were driving for when the car shut down? I remember reading about a guy who claimed his D would die after 5 minutes and 30 seconds and he would coast to a stop and wait for 10 minutes or so and it would restart and drive normally. It turned out to be the pickup coil. He said he did that whole routine for months and it was a fairly simple fix.
davidc89
09-19-2016, 08:49 PM
Did you have the air conditioning on?
Jimmycxc
09-20-2016, 02:03 PM
Previously, I had driven about an hour and a half, stopped for a few hours, then drove back home and everything was fine. On Monday, I drove maybe 25 minutes, stopped for about an hour, then drove home and that's when it happened.
I did have the AC on.
davidc89
09-20-2016, 08:04 PM
Mine will do that from time to time if I have the a/c running.
David T
09-20-2016, 09:29 PM
For those who suggested checking the impulse coil, they typically fail when they get hot. For example, you start and drive normally but after about 20 minutes the engine dies and won't restart til it cools. Also seems to be very repeatable. They can fail in other ways too but that is less likely. I just had a car that was running fine and then suddenly developed a no-start. It was the connection where the wire plugs into the distributor (and the coil). Cleaned it up and now it starts every time. The way to troubleshoot is to first try to figure out if it is the fuel system or the ignition system. Two very different causes. Once you can rule out either system the possibilities narrow down considerably. The next time it dies check for spark or fuel immediately. Whichever is not present is the problem. More often than not the root problem is electrical in nature, especially if it is ignition. To do a quick check for fuel press on the air sensor plate and see if there is any back-pressure. If none, then you don't have fuel. Another quick test is a shot of Ether. If that doesn't do it you don't have spark. Or you can pull a spark plug wire and see if you have any spark while cranking. Important to do it as soon as you can after it dies while the motor is still hot.
Jimmycxc
09-21-2016, 04:34 PM
So it's not an engine warming issue. I wanted to move the car to another garage that had more room. I started it up, backed up, and drove the 300 feet to the end of my street. When I pushed in the clutch to stop, so did the engine. Would not start up again. Pushed the car to my driveway, got mad, gave it full throttle as I turned the key and it fired right up. Put it back in my garage and closed the door.
I did notice that my new fuel pump was making a slightly different tune than the normal hum I've come to love when it's priming. I also realized the car shut off when there is a sudden drop in rpms, like when pushing in the clutch. I'm wondering if my pump could be acting up again, but it is a brand new pump. Will have to check the volts again.
I'm no mechanic, but what about a collapsing rubber fuel pickup hose? Just throwing it out there.
Bitsyncmaster
09-21-2016, 06:53 PM
Does your idle hold 775 RPM at normal idle?
Sounds like you have a problem with the idle circuit since it started wide open.
David T
09-21-2016, 09:39 PM
I'm no mechanic, but what about a collapsing rubber fuel pickup hose? Just throwing it out there.
That is certainly a possibility but before guessing at the cause it is helpful to determine if it is a fuel or ignition problem. Also we don't know if he has the original style fuel pick-up or the newer one that wouldn't have the hose.
Jimmycxc
09-28-2016, 11:13 AM
That is certainly a possibility but before guessing at the cause it is helpful to determine if it is a fuel or ignition problem. Also we don't know if he has the original style fuel pick-up or the newer one that wouldn't have the hose.
I do have the old style with the hose. Dave, do you happen to have a picture of the plug for the distributor and coil? I am on an anniversary vacation, but will be working on the car this weekend. Thanks!
Jonathan
09-28-2016, 01:36 PM
I do have the old style with the hose. Dave, do you happen to have a picture of the plug for the distributor and coil? I am on an anniversary vacation, but will be working on the car this weekend. Thanks!
The wire that goes between the ignition coil and distributor is here:
http://store.delorean.com/p-6871-wire-ign-coil.aspx
I believe both ends of this wire have the same style plug. That plug is similar to the distributor end of the spark plug wires (but unlike the end that connects to the spark plug itself).
It is the red wire in this photo:
46385
The replacement coil wire may come in black, as I believe those were improved quality over the red ones.
When you push down on any of those plug end connections, at the distributor or the top of the coil, you should be able to feel it snug into place. You should not be able to lightly pull up on it from the wire and have the plug come off, it is much more firm of a connection than that. If it does come off loose, it isn't on all the way or something is out of sorts with the connection on the wire or the coil or distributor.
DMCVegas
09-28-2016, 02:29 PM
Does your idle hold 775 RPM at normal idle?
Sounds like you have a problem with the idle circuit since it started wide open.
I had that same problem. Driving home one night, pull up to a stop light and the engine dies. Fires right back up, but as soon as I took my foot off the gas it died again. Had to hold the gas pedal down to keep the engine from dying on the way home. Hit the wires between the ISM and the ECU with a multi meter to check resistance and found a bad one. Spliced in a new wire and never any any more trouble.
Jimmycxc
09-28-2016, 04:04 PM
I had that same problem. Driving home one night, pull up to a stop light and the engine dies. Fires right back up, but as soon as I took my foot off the gas it died again. Had to hold the gas pedal down to keep the engine from dying on the way home. Hit the wires between the ISM and the ECU with a multi meter to check resistance and found a bad one. Spliced in a new wire and never any any more trouble.
Thanks. I would definitely need some pics to fully understand what you did. I can splice in new wires, but not sure where everything is located.
Also, with my issue, it doesn't always start right back up. I need to do more investigating to get more information.
DMCVegas
09-28-2016, 05:26 PM
Thanks. I would definitely need some pics to fully understand what you did. I can splice in new wires, but not sure where everything is located.
Also, with my issue, it doesn't always start right back up. I need to do more investigating to get more information.
When cranking, hold the gas pedal down ¼ of the way. RPMs will shoot up, but don't be scared. Just make sure it runs. THEN take your foot off the pedal and see if it dies.
I don't have any pictures right now since I am no where near my car. However, for you anyone else coming into this thread, here is a quick video to give you an idea about how to check continuity to first watch:
https://www.youtube.com/watch?v=5G622WDZaHg
Now not all meters will have the ability to beep. So you'll just have to keep an eye on your meter's gauge or display. But I have a feeling that most of us probably have something close to the Cen-Tech Harbor Freight special, so I'll reference one of those.
Set the Meter to ohms, 200 Ω to be exact. Touch the leads and you should pretty much have zero resistance. Now whenever you touch the opposite ends of a single wire, you should pretty much get the same result on the meter. This will tell you two things:
The wire is in good shape and shows connectivity.
If you're trying to sort out & locate an individual wire, you've not just located the correct one.
Now to check the wires between the Idle Speed Motor and the Idle Speed ECU, it's pretty easy.
Disconnect your car battery! Yeah can probably just leave the key out, but it's a good safety habit to get into. Hit the wrong wire that's powered, and you can risk electrical damage. Or even blown fuses, and that's just irritating.
Unplug the 3-wire connector from on top of the ISM. Then unplug both connectors from the back of the ECU. You should see one plug that contains Four wires, and another that contains Five. The plug that has has Five wires is the one you want to focus on. Wire 1 is 12V power, 2 is Ground (or Earth), and 3, 4, & 5 are the ones that connect to the ISM. Those are the ones you want to check. In this picture, look at the plug on the left with the five prongs. See the two on the bottom, and then that 3rd on the top, off by itself, all the way to the right? Those are the leads that power the ISM. Simply mirror that image to see which of the sockets on the wiring harness they plug into.
46390
Refer to Item 108 on your Master Wiring Schematic for further clarification and wiring color codes.
Now, you're gonna need some extended leads here because of the different locations inside of the Engine Compartment and the Passenger Compartment. But it can be done. Just connect your lead extensions first and verify the absence of resistance on your test wires to make sure they're all good. Then just plug the probes into the sockets to check for continuity.
No resistance on your wires means that they're good. Any resistance or failed continuity means that they're bad. Resistance may just mean some corrosion that needs to be cleaned off. So check your connections, clean them, and then retest. But it can also mean a bad wire with a potential break. In my case, I isolated the single bad wire, and then cut it an inch away from the ISM plug. I verified continuity through the plug itself was good, so then I just pulled a fresh wire in along side the harness, severed the bad wire behind the ECU plug too, and then just spliced it in. Everything worked just fine after that.
Is this the same problem you're having? I don't know. But before you cut anything, follow these instructions to test your wiring. And make sure you always disconnect and isolate the wire to fully test it for proper continuity.
Jimmycxc
10-02-2016, 12:40 PM
A little update. The car starts up great on a cold start. It idles, although it does hunt a little bit (always done this). I can rev up the engine and it goes back to idling.
So I decided to try and move it to the other garage again. I got a little farther this time before it stalled the first time. I got into 2nd gear by keeping on the gas a little while I shifted and as long as I kept on the pedal, the car would drive. As soon as I let off, the engine would die. When it died, I would coast for as long as I could. I found out if, I tried to start it by pushing in the clutch and turning the key while I was still coasting, it would start right up. If I came to a stop, I would have to give it full throttle for it to start.
I still have to check for continuity between the ISM and Idle Speed ECU. I will hopefully have an update for everyone by the end of the day.
Jonathan
10-02-2016, 01:31 PM
Sounds to me like your idle speed microswitch isn't engaging. Loosen the lock nut on the upper post and dial it in one full rotation (360 deg) towards the microswitch tab. Tighten the nut and go take it for a test drive. Double check the electrical connections on the switch are ok too while you're there. There are only two, the black ground goes to the top and the black/green one goes to the lower tab. Make sure neither of those has fallen off or is loose.
Jimmycxc
10-02-2016, 03:16 PM
Still troubleshooting and discovered this...Took the air filter box off and with the car running at idle, I push down on the plate and it immediately stalls.
Bitsyncmaster
10-02-2016, 03:32 PM
Still troubleshooting and discovered this...Took the air filter box off and with the car running at idle, I push down on the plate and it immediately stalls.
Does what it should. That air plate is not the throttle plate. It adjusts the mixture so your basically shooting to much fuel with very little air.
Jimmycxc
10-02-2016, 03:40 PM
Does what it should. That air plate is not the throttle plate. It adjusts the mixture so your basically shooting to much fuel with very little air.
Gotcha. Thanks Dave
Jimmycxc
10-02-2016, 04:01 PM
When cranking, hold the gas pedal down ¼ of the way. RPMs will shoot up, but don't be scared. Just make sure it runs. THEN take your foot off the pedal and see if it dies.
I don't have any pictures right now since I am no where near my car. However, for you anyone else coming into this thread, here is a quick video to give you an idea about how to check continuity to first watch:
https://www.youtube.com/watch?v=5G622WDZaHg
Now not all meters will have the ability to beep. So you'll just have to keep an eye on your meter's gauge or display. But I have a feeling that most of us probably have something close to the Cen-Tech Harbor Freight special, so I'll reference one of those.
Set the Meter to ohms, 200 Ω to be exact. Touch the leads and you should pretty much have zero resistance. Now whenever you touch the opposite ends of a single wire, you should pretty much get the same result on the meter. This will tell you two things:
The wire is in good shape and shows connectivity.
If you're trying to sort out & locate an individual wire, you've not just located the correct one.
Now to check the wires between the Idle Speed Motor and the Idle Speed ECU, it's pretty easy.
Disconnect your car battery! Yeah can probably just leave the key out, but it's a good safety habit to get into. Hit the wrong wire that's powered, and you can risk electrical damage. Or even blown fuses, and that's just irritating.
Unplug the 3-wire connector from on top of the ISM. Then unplug both connectors from the back of the ECU. You should see one plug that contains Four wires, and another that contains Five. The plug that has has Five wires is the one you want to focus on. Wire 1 is 12V power, 2 is Ground (or Earth), and 3, 4, & 5 are the ones that connect to the ISM. Those are the ones you want to check. In this picture, look at the plug on the left with the five prongs. See the two on the bottom, and then that 3rd on the top, off by itself, all the way to the right? Those are the leads that power the ISM. Simply mirror that image to see which of the sockets on the wiring harness they plug into.
46390
Refer to Item 108 on your Master Wiring Schematic for further clarification and wiring color codes.
Now, you're gonna need some extended leads here because of the different locations inside of the Engine Compartment and the Passenger Compartment. But it can be done. Just connect your lead extensions first and verify the absence of resistance on your test wires to make sure they're all good. Then just plug the probes into the sockets to check for continuity.
No resistance on your wires means that they're good. Any resistance or failed continuity means that they're bad. Resistance may just mean some corrosion that needs to be cleaned off. So check your connections, clean them, and then retest. But it can also mean a bad wire with a potential break. In my case, I isolated the single bad wire, and then cut it an inch away from the ISM plug. I verified continuity through the plug itself was good, so then I just pulled a fresh wire in along side the harness, severed the bad wire behind the ECU plug too, and then just spliced it in. Everything worked just fine after that.
Is this the same problem you're having? I don't know. But before you cut anything, follow these instructions to test your wiring. And make sure you always disconnect and isolate the wire to fully test it for proper continuity.
Got 4 ohms resistance one the first wire. 0.3 Olmsted second wire, and no continuity for the third. Looks like I need to run a new wire.
Jimmycxc
10-02-2016, 04:28 PM
Not sure what happened, but when I tested everything again before I spliced in a new wire and now each wire is either zero or 0.4 ohms.
Elvis
10-02-2016, 05:04 PM
The micro switch does NOT turn the idle ECU or the idle motor off !!!
there's thousands of infos about the idle system here in the forum...
Sounds to me like your idle speed microswitch isn't engaging. Loosen the lock nut on the upper post and dial it in one full rotation (360 deg) towards the microswitch tab. Tighten the nut and go take it for a test drive. Double check the electrical connections on the switch are ok too while you're there. There are only two, the black ground goes to the top and the black/green one goes to the lower tab. Make sure neither of those has fallen off or is loose.
David T
10-02-2016, 05:25 PM
The micro switch does NOT turn the idle ECU or the idle motor off !!!
there's thousands of infos about the idle system here in the forum...
For all practical purposes you can say it "turns it off". Refer to the Workshop Manual D:05:02. The Idle Speed Control System is only "in operation" when the throttle plates are closed and the micro switch provides a ground path for the ECU via the B/LG wire. From a more technical point of view, the Idle ECU is always on, it is just not controlling the Idle Speed Regulator, aka idle air motor. The idle ECU is getting power whenever the key is in the RUN or Start position. For a more complete description of the Idle Speed Control System refer to Section D:05
DMC5180
10-02-2016, 06:46 PM
This story may be long winded, but a Delorean Adventure with a Happy ending is GOOD THING and the found fault could be applicable to this thread topic.
I had a recent Failure to start a couple weeks ago. First time in my 22 years ownership. I had packed up the car for a 4 hr road trip and when I went to leave it would not start. My car has never failed to start before for no apparent reason. I checked the obvious things, resistor connections, Fuel pump, Etc. Nothing I tried worked. We were running behind our scheduled departure time, so I packed up the daily driver and left it to when I got back home. Once, I returned, I did more confirmation checks. On one of those checks I went into the ECU bay and wiggled the two connectors in the Idle ECU and followed that a crank attempt. Boom It fired right up. Thinking somehow the IDLE ECU may have lost connection to the ISM, I figured this may have been the plausible reason for the NO START.
Now Fast forward 2 weekends, Friday I go out to the garage and start the car up just to be sure I don't get Surprised when I need to take it on long drive to partake in a Midwest Tech day. The car fires up and I let it go through normal warmups and everything appears fine. Okay, so SATURDAY Morning at 3:30 AM, I get ready to leave on a 400 mile drive to the Tech day. The car fires right up and I leave, I stopped for fuel and fill up. Everything is hunky dory, UNTIL about 3 miles down the road the ENGINE SHUTS DOWN. I Let the car roll as far as I can until I see a side road I can pull off on. I come to a full stop Open the door and then try cranking a couple times, NOTHING. Less than 30 seconds later a vehicle pulls in behind me from off the Highway that had been traveling the opposite direction. AND the LIGHTS COME it was a county Sheriffs Deputy. I walked back to his car and explained what had just happened, I can only imagine what the guy was thinking at seeing a Delorean off the side of the road at 4 AM. Anyway, after the usually Plate run and DL check, He offered to call a tow truck If I needed it. I said, I would do that IF needed and that I could roll the car off the road into a Drive way just ahead of me that just happened to be Country Church. I told him I was going to call my wife to come get me since I was just barely out of town. He said, no problem and I thought I was going to need to leave the car unattended, to just call it into dispatch to let them know and then he went on his way. I called the wife and told her what had happened and to come get me. So while I was waiting for her to arrive. I did a few more diagnostics including jumping the RPM relay. (always carry a jumper in he car) I could here the pump running but It still would not start. So on a hunch I decided to go back into the ECU compartment and check the IDLE ECU Connection again. Wiggle,wiggle and Crank, NOTHING! Then, just for shits, I put my fingers on the IGNITION ECU connector, you can barely move it due to its difficult location. I crank the engine Engine again and SHE FIRES RIGHT UP. WOW I think, maybe it was not the Idle ECU connection I had previously thought it was. I must have disturbed the Ignition ECU connection under the Idle ECU connectors when I was checking those 2 weeks earlier. With the engine running, I did a verification of the Ignition ECU connector rocking it side to side until one side popped loose, just barely I might add, and the engine dies. I grab screwdriver and managed to pry the connector off the ECU to examine it. NOTHING appeared abnormal, so I just re-connected it and the engine fired right back up. Right about that time the phone rings and my wife is nearby but can't seem to find me. (misunderstanding in location details) I told her what I had found and told her the car was running and I would come back into town and meet her at a well lit location. After we met up, I told her I thought a had found the root cause to my NO START problem and decided I would proceed on my Tech DAY trip. The Car ran fine and I just returned from an 800 mile ROUND TRIP. It was a Saturday Event and probably one of the last times the car will get out this year save for some fall color touring.
The moral here is that we tend to overlook the remote causes for NO STARTS. It is largely Agreed that the Ignition ECU almost never fails, so it tends to get overlooked. But in this case the ECU connection developed light oxidization and lost connection. Hopefully, just pulling the connector off and reinstalling it scratched fresh points of contact on the terminals and it will be okay. At least if I have another NO START or Random SHUT DOWN , I'll know what not to overlook.
Bitsyncmaster
10-02-2016, 06:53 PM
The micro switch does NOT turn the idle ECU or the idle motor off !!!
there's thousands of infos about the idle system here in the forum...
+1
When I was designing my idle ECU I tested the stock unit and never found the idle switch to do anything to the ECU. Now it may have changed a little timing but I never put much effort into analyzing it. The main purpose of the idle switch is to turn the ignition advance on or off.
Someone with the stock ECU should pull a wire off that diode near the idle ECU and see if anything changes with your idle.
Jimmycxc
10-02-2016, 08:53 PM
Just ordered a new set of relays just for shits and giggles.
David T
10-02-2016, 09:07 PM
That was a long-winded little story! The moral of the story should be if you have an intermittent you cannot be sure it is fixed unless you actually find the problem. You may have disturbed it and got the motor running again but until it is fixed you can't trust it. You can expect the problem to occur again. I would suspect the wire to the impulse coil, the coil itself, or the connections to the ballast resistor. I don't see how the idle ECU can prevent the motor from running or shut it down. The next time it happens you should immediately check for spark to verify an ignition problem.
DMC5180
10-02-2016, 11:06 PM
David,
The Original No Start Happen in my Garage after previously parking a running car following my 2 week Vacation driving tour that coincided with DCS 16.
Imagine my surprise when I go to start the car two weeks ago. As I stated, the last item I touched was the Idle ECU prior to it starting up like nothing happened. This apparent coincidence led me to think the plausible cause was a poor connection at one of the idle ECU connectors. Btw, what usually happens when You pull the Connector off the ISM when the Engine is running? Not trick question. The engine has a tendency to stumble and or quit. The valve closes and starves the Engine of Idle control Air. So it's plausible that if the ISM lost partial signal it could be driven closed. This possibility led me to believe thats what had happened. Also, I never consciously heard the ISM hum. Of coarse I wouldn't if the key was Off While I was checking the usual suspects. iE resistor connections, ignition coil, coil wire both ends. And I had confirmed I had functioning Impulse coil, the RPM relay was running the FP And TACH needle was Bouncing while Cranking, but it did not fire till I after I had Wiggled the Idle ECU connection.
The engine shutting down on me after leaving the gas station made me ponder other possibilities. I recalled recently that someone else on the forum experienced a similar situation. He went through all the connections and found the Ignition ECU connector was not fully seated. He heard it Click after touching it. His engine started right up after that one. This is what made me go to that connector and see if that was a possibility. In my case it was kind of I'm very confident I found the Smoking Gun. I think my 800 mile trip gives me that reassurance. I'll look at the glass as half full, you can see it as half empty and continue to cast doubt. [emoji6]
I'm good with what I found. I'll agree with you that those items you mentioned are always a potential suspect.
Sent from my iPhone using Tapatalk
Jimmycxc
10-15-2016, 11:28 AM
Update:
Received my new relays and put them in. Fuel pump will not turn on now. Tried jumping it and nothing. I removed the new Lambda relay and plugged the old one back in. Fuel pump turns on and car starts and idles. However, it will turn off after about 30 seconds. When it shuts off I can hear and feel the idle speed motor buzzing. Fuel pump, when running is getting 11.4 volts. When engine dies, so does the voltage to the fuel pump. I've tested the inertia switch and it works as it should...with it up, the fuel pump does not work, I push it down, fuel pump works.
Bitsyncmaster
10-15-2016, 12:36 PM
The lambda relay should have no effect on the the fuel pump running. Maybe someone modified your wiring. The RPM relay powers the fuel pump and drives the lambda relay coil. Maybe that lambda relay coil is shorted but that would have blown the fuse.
Jonathan
10-15-2016, 04:32 PM
Is this thing you mentioned about it shutting off after about 30 seconds repeatable? And is the duration exactly the same each time? (30 seconds, or 45 seconds, or 22 seconds, etc.) If you can get the car to keep doing what you've described consistently, it'll help you narrow down what the problem is.
Jimmycxc
10-15-2016, 04:55 PM
I would not call it consistent. ill have to time if a few times to really see. I took off the air filter and watched the air flow sensor plate during idle. Right before it dies, the plate moves down on its own.
Jonathan
10-15-2016, 05:29 PM
That air plate moving down on its own would mean you're losing fuel pressure, right? Might be beneficial to get some fuel pressure gauges hooked up and see what is really happening.
Could be a pump suction problem. Or could be something after the pump constricting things, like a plugged filter perhaps?
Jimmycxc
10-16-2016, 11:31 AM
That air plate moving down on its own would mean you're losing fuel pressure, right? Might be beneficial to get some fuel pressure gauges hooked up and see what is really happening.
Could be a pump suction problem. Or could be something after the pump constricting things, like a plugged filter perhaps?
Was thinking it could be as simple as a plugged filter. Can't hurt to replace it. I did take the pump out and checked it the suction hose was collapsed, but it was good.
DMC-81
10-16-2016, 11:46 AM
Was thinking it could be as simple as a plugged filter. Can't hurt to replace it. I did take the pump out and checked it the suction hose was collapsed, but it was good.
One other thing I would check as well is the little screen in the CPR/WUR. What does the air plate do after you shut the engine off, (and before it dies)? I wonder if it goes down as well, or if it's just while the engine is idling?
David T
10-16-2016, 03:26 PM
Was thinking it could be as simple as a plugged filter. Can't hurt to replace it. I did take the pump out and checked it the suction hose was collapsed, but it was good.
Before guessing and "throwing" parts at the problem you should do some systematic testing to try to determine exactly what the problem is and what is causing the problem. Disturbing things and changing parts (possibly good parts) can introduce other problems that you didn't already have. Rare for a filter to get so plugged up as to stop the motor from running. Other things are more likely like a collapsing suction hose.
Jimmycxc
10-29-2016, 10:01 AM
After all this, it's the inertia switch. Bypassed temporarily and car ran great for 45 minutes before I turned the key off. Ordered a new one and should be here by Tuesday. Thank you all again for everyone's help!
David T
10-29-2016, 01:56 PM
Did the bad one (the one you bypassed) have a splotch of white paint on it? If not it was never changed during the recall and was defective. When reinstalling make sure you install it on the footwell wall NOT the Lambda counter. Do not mix up the wires. Two are for the fuel pump and 2 are for the Central Locking System to unlock the doors.
Jimmycxc
10-31-2016, 04:00 PM
Did the bad one (the one you bypassed) have a splotch of white paint on it? If not it was never changed during the recall and was defective. When reinstalling make sure you install it on the footwell wall NOT the Lambda counter. Do not mix up the wires. Two are for the fuel pump and 2 are for the Central Locking System to unlock the doors.
Apparently, mine was never changed out after all these years. I have no white splotch. It is located on the footwell though.
vin6635
10-23-2017, 11:33 AM
Thanks everyone - I found a bad wire on my ballast resistor killed my car a few weeks ago. Quick and simple fix and now back up and running (at least till the weather gets worse...).
PJ Grady Inc.
10-24-2017, 01:41 AM
Apparently, mine was never changed out after all these years. I have no white splotch. It is located on the footwell though.
According to your VIN you have an 83. From 82 on the cars were fitted with the updated switches but DID NOT HAVE A WHITE DOT OF PAINT. Don't replace the switch as it should be fine. There may be a small S stamped onto the housing. If not check for 2 brass outer terminals and a chrome center one at the plug in. That also means it's an updated switch. The recalled switches had three brass terminals at the connection point.
Rob
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.