Log in

View Full Version : Suspension Do shocks drop with age



Bitsyncmaster
09-26-2016, 04:07 PM
I have had Hervey's easy rider shocks on my car for 6 or 7 years and noticed the drivers side rear end is about a half inch lower than the passenger side. I did not see any movement in the clamp that holds the spring seat so I'm guessing the shocks may be a gas charge and one has leaked.

Are all the shocks gas charged?

Drive Stainless
09-26-2016, 08:01 PM
I have had Hervey's easy rider shocks on my car for 6 or 7 years and noticed the drivers side rear end is about a half inch lower than the passenger side. I did not see any movement in the clamp that holds the spring seat so I'm guessing the shocks may be a gas charge and one has leaked.

Are all the shocks gas charged?

Dave,

Shocks don't affect ride height; they just resist movement from the vehicle's equilibrium height. If the shock missing, the car would sit at the same height.

Differences in ride height at each wheel on these cars are very common. You can solve it easiest with a coilover setup. :)

sdg3205
09-26-2016, 08:46 PM
They should have a mild effect on height, shouldn't they? They are essentially constantly pushing up unless at full travel.

Michael
09-26-2016, 09:45 PM
They should have a mild effect on height, shouldn't they? They are essentially constantly pushing up unless at full travel.

I would think so. After being on a lift, mine usually sits about an inch higher until it settles back down.

Drive Stainless
09-26-2016, 11:08 PM
They should have a mild effect on height, shouldn't they? They are essentially constantly pushing up unless at full travel.

Theoretically, they should not be pushing up. If they are pushing up, then they're effectively increasing the spring rate. I would be interested in knowing what sort of force they're pushing with. I would hope and expect that it amounts to <1% of the total weight on that axle so as to be negligible.

Josh
09-26-2016, 11:53 PM
The shocks do not affect the ride height as Matt outlined...

sdg3205
09-27-2016, 12:30 AM
Fair enough.

Bitsyncmaster
09-27-2016, 06:33 AM
I thought I remembered struts on my Malibu pushed up about 20 lbs of force before any spring was attached. Just wondered if any shocks did the same.

DMC-81
09-27-2016, 08:49 AM
On the DeLorean, I don't think that is the case. When I installed mine, I had to lift the bottom of the strut assembly with a jack slightly against the pressure of the spring to attach the top nut on the shock.

Looking at a pic of the unit, I think the only way the ride height would be affected is if the spring cup collar moved.

46380

Incidentally, I had bought that clamp on collar shock configuration when I first got my car (with the the red adjustable KYB option). When the package arrived, I was concerned about the setup, so I called KYB technical support, and asked them if the shock body for that model was recommended to carry such a load. They said that they would definitely not recommend that usage. Then I asked them how thick the metal was on the shock wall. They said it was 1.2 mm. :eek1: That's like a metal gas charged balloon. I returned the rear shocks and collars. I heard that lots of people have used them, but after that phone call, they were not for me. :paranoid: I really can't understand how they can work, but I guess they do. Maybe other shock models have thicker metal?

Do you have a picture of the one that is lower, especially around the collar? I wonder if the metal below the clamp has buckled, or if the collar slipped a bit, especially since the collar torque is supposed to be "just snug" on a smooth surface friction fit. :dunno:

Alternatively, is the shock leaking or wet in another area?

Josh
09-27-2016, 11:38 AM
Dana you do raise a good point, and a concern I always had with John's rear shock setup.

Perhaps the change in height is the collar letting go and sliding downwards (very scary)

You can buy NOS rear Girlings for $75 a set you know? Great deal if you ask me and properly designed for the rear "coilover" setup.

Ryan King
09-27-2016, 09:37 PM
Dana you do raise a good point, and a concern I always had with John's rear shock setup.

Perhaps the change in height is the collar letting go and sliding downwards (very scary)

You can buy NOS rear Girlings for $75 a set you know? Great deal if you ask me and properly designed for the rear "coilover" setup.

I went BACK to the original Girling shocks for the rear. Other aftermarket shocks aren't designed to handle the weight of our engines. I blew out to sets of shocks in the rear, and too many to count for the front. The fronts were due to lowered suspension. I went back to stock height in the fronts, and opted for a KYB set for the front. No regrets. Car rides great.

-Ryan

Lwanmtr
09-28-2016, 11:34 PM
I'd almost think my shocks have collapsed a bit...they are old, crusty and hard.... and one was even leaking.

DMCMW Dave
09-28-2016, 11:41 PM
You can buy NOS rear Girlings for $75 a set you know? Great deal if you ask me and properly designed for the rear "coilover" setup.

Agree - the NOS Girlings at $75 a pair are a smokin' deal especially if you are retrofitting from one of the collared designs that has failed and want to economize. They typically ride very well as, although they are 30+ years old any that I've seen are still holding pressure. Just don't forget to get the retainers (4 needed) at the same time unless they are still in the car somewhere. Part 101205A but any of the shops ought to have dozens of them laying around as they are not used on any of the conversions.

The best solution is the current aftermarket shock from the DMC dealers, but if you are on a budget the Girlings work well.

DMC-81
09-29-2016, 07:53 AM
The best solution is the current aftermarket shock from the DMC dealers, but if you are on a budget the Girlings work well.

I agree. That is what I ended up going with. I like that they are plug and play, painted black, with poly bushings, and I think 17 adjustments on the dial on both front and rear shocks. They look like very sturdy units, and I'm happy with them so far.

I know that it is to each their own on these parts, but I happen to be very concerned about the clamp on collar solution.

Nicholas R
09-29-2016, 09:38 AM
The best solution is the current aftermarket shock from the DMC dealers, but if you are on a budget the Girlings work well.

What are the current aftermarket shocks from the DMC dealers?

Because the website shows these:
http://store.delorean.com/images/Product/large/gt100110.jpg

But I thought it may be these:
http://www.delorean.eu/catalog/images/producten/groot/GT100114PP.jpg

David T
09-29-2016, 12:32 PM
As long as we are talking about shocks, I am amazed that unless you have a very high mileage car, the shocks are leaking or otherwise damaged, the original ones can still work satisfactorily.

Jason
09-29-2016, 12:44 PM
I had front springs on my car that slowly dropped with age and eventually had to be replaced because the car rode too low. Could it be your spring is going bad?

Patrick C
09-29-2016, 01:07 PM
What are the current aftermarket shocks from the DMC dealers?

Because the website shows these:
http://store.delorean.com/images/Product/large/gt100110.jpg

But I thought it may be these:
http://www.delorean.eu/catalog/images/producten/groot/GT100114PP.jpg

All of the DMC vendors sell Ed Uding's shock kits now.

Grady appears to sell similar now too:
https://www.pjgrady.com/product/avo-shock-absorber-suspension-kit/

Drive Stainless
09-29-2016, 02:01 PM
All of the DMC vendors sell Ed Uding's shock kits now.

Grady appears to sell similar now too:
https://www.pjgrady.com/product/avo-shock-absorber-suspension-kit/

Does AVO actually have an American distributor, or are all of the vendors importing the shocks from the UK on their own behalf?

Something to consider:
We've seen past failures with the SPAX suspension. As a result, the vendors have stopped carrying them. Should one of these AVO suspension components break and cause injury as a result of a manufacturing defect, who will you sue? With no American distributor, it's unlikely you could get personal jurisdiction over UK-based AVO. Therefore, you'd be stuck suing in the UK, which means you'd have an uphill battle from the very beginning with finding a UK-based attorney, paying to lodge and fly your witnesses to the UK, and then you'd pray for justice from an unavoidably biased English jury. Good luck.

On the other hand, you could buy a USA-made suspension manufactured right here in Minnesota and with dealers located throughout the nation (http://www.qa1.net/dealers). If trouble finds you, you can almost certainly sue QA1 in your home or neighboring state based on specific jurisdiction (minimum contacts).

Note that this post is not meant to be construed as legal advice nor does it create an attorney-client relationship.

David T
09-29-2016, 02:44 PM
Does AVO actually have an American distributor, or are all of the vendors importing the shocks from the UK on their own behalf?

Something to consider:
We've seen past failures with the SPAX suspension. As a result, the vendors have stopped carrying them. Should one of these AVO suspension components break and cause injury as a result of a manufacturing defect, who will you sue? With no American distributor, it's unlikely you could get personal jurisdiction over UK-based AVO. Therefore, you'd be stuck suing in the UK, which means you'd have an uphill battle from the very beginning with finding a UK-based attorney, paying to lodge and fly your witnesses to the UK, and then you'd pray for justice from an unavoidably biased English jury. Good luck.

On the other hand, you could buy a USA-made suspension manufactured right here in Minnesota and with dealers located throughout the nation (http://www.qa1.net/dealers). If trouble finds you, you can almost certainly sue QA1 in your home or neighboring state based on specific jurisdiction (minimum contacts).

Note that this post is not meant to be construed as legal advice nor does it create an attorney-client relationship.

I doubt very much that people's buying decision is based on who and where you can sue them. I agree it is a hassle on many counts when you buy overseas and for myself I prefer to buy "American" where possible. That said, because of the currency values, you can get a bargain if you don't mind ordering overseas and waiting.

Josh
09-29-2016, 03:34 PM
Does AVO actually have an American distributor, or are all of the vendors importing the shocks from the UK on their own behalf?

Something to consider:
We've seen past failures with the SPAX suspension. As a result, the vendors have stopped carrying them. Should one of these AVO suspension components break and cause injury as a result of a manufacturing defect, who will you sue? With no American distributor, it's unlikely you could get personal jurisdiction over UK-based AVO. Therefore, you'd be stuck suing in the UK, which means you'd have an uphill battle from the very beginning with finding a UK-based attorney, paying to lodge and fly your witnesses to the UK, and then you'd pray for justice from an unavoidably biased English jury. Good luck.

On the other hand, you could buy a USA-made suspension manufactured right here in Minnesota and with dealers located throughout the nation (http://www.qa1.net/dealers). If trouble finds you, you can almost certainly sue QA1 in your home or neighboring state based on specific jurisdiction (minimum contacts).

Note that this post is not meant to be construed as legal advice nor does it create an attorney-client relationship.

That escalated quickly lol

You crazy Americans.

sdg3205
09-29-2016, 03:59 PM
That escalated quickly lol

You crazy Americans.

Lol!

Drive Stainless
09-29-2016, 04:17 PM
That escalated quickly lol

You crazy Americans.

LOL, well it wasn't made to escalate anything, but it's something to consider. Terrible things happen in the world, and after about 50 credits of reading about terrible things, I've changed a lot about the way I make choices.

DMC-81
09-29-2016, 09:32 PM
I did some searching and AVO Shocks were apparently designed by Ron Avon, the same guy who designed Protech shocks, so say the guys and gals on the UK automotive forums.

dodint
09-29-2016, 10:18 PM
LOL, well it wasn't made to escalate anything, but it's something to consider. Terrible things happen in the world, and after about 50 credits of reading about terrible things, I've changed a lot about the way I make choices.

I'm only six weeks in and I'm seeing everything as some kind of possible tort. Hoping this sickness goes away so I can return to enjoying life. ;)

delo2.8
10-24-2016, 10:35 PM
Dana you do raise a good point, and a concern I always had with John's rear shock setup.

Perhaps the change in height is the collar letting go and sliding downwards (very scary)

You can buy NOS rear Girlings for $75 a set you know? Great deal if you ask me and properly designed for the rear "coilover" setup.

I put John's rear setup on my car. A few weeks after installation I hit a decent pot hole and the drivers side collar slipped down to the bottom of the shock, pretty scary. I talked to a mechanic friend of mine who works on a lot of aftermarket and high performance vehicles in his shop and he took one look at it and said he would never run anything like that.

Bitsyncmaster
12-18-2016, 12:53 PM
Well I checked the collars on the Hervey rear shocks and both are still in the same location. But the drivers side height is a half inch lower than the passenger side. I do remember tightening the collars when I first installed the shocks.

I am going to install NOS rear shocks and see if that corrects the problem. I never noticed any ride difference when I installed the rear easy riders anyway.

nkemp
03-18-2017, 01:58 PM
When I redid my frame about 27 years ago, I installed Fred Lockett's (AKA DeLorean Pilot) lowering springs as that was the only option to cut-n-swap. I have no idea what springs he used. (So much for the better has changed in the last 27+ years !!!) I also installed NOS shocks at the time.

Now my rears have a lot (LOT) of camber and I suspect that the springs are compressing. It is like the frog in water approaching boiling, it just keeps creeping up until one day you look at it (the frog or the camber) and notice how bad it looks. Plus the driver side may be lower than the passenger side. So my input is that it may be your springs compressing and as someone pointed out, after the car is on the lift, the car rides a bit high for a while which could be the springs stretching back out.

As I recall, shocks are pretty neutral relative to support. That said, when you push shocks in by hand, don't they move back out on their own? But the outward force is minimal.

So I'm now in process of researching what to do.
- New springs & shocks all around (I've wanted to get the front about an inch lower)
- Reinstall the OEM rear springs in the rear keeping the OEM shocks
- Install the OEM fronts in the rear and keep the shocks
- New Springs & shocks for the rear
- Other?

I really hate the idea of redoing the fronts. The last time the spring compressor failed while I was holding/moving it under compression. That was exciting ... and didn't cause me any harm :-)

Bitsyncmaster
03-18-2017, 03:09 PM
I've got NOS rear shocks waiting for the warmer weather to replace my easy riders. Yes the NOS shocks do extend them self but like you said, it's not much force.

David T
03-18-2017, 04:06 PM
I've got NOS rear shocks waiting for the warmer weather to replace my easy riders. Yes the NOS shocks do extend them self but like you said, it's not much force.

Shocks do not affect ride height. Shocks with springs on them (coil-overs) DO affect ride height. Not the shock itself but the spring around the shock. Usually with coil-over springs there is some kind of adjustment so you can change the ride height. A collar that just clamps in place is not considered "Good Practice" since it can (and often does) slip. There is a LOT of force on that spring and eventually a clamped collar will move. Good coil-overs will have threads on the outside of the shock and collars that screw on those threads. Better coil-overs will also have some external adjustment screws so you can modify the shock's control. The main function of the shock is to control the up-and-down movement of the suspension, not to lift it. It is finely tuned to the tire, the frame's resonance and stiffness, and the road surface. A properly tuned shock is akin to a tuning fork, it absorbs resonate frequencies and damps them out. You cannot throw any shock into a car and expect proper performance.

Gregadeth
03-20-2017, 08:57 PM
Has anyone adjusted the ride height on their AVO rear coilovers that DMC currently sells? Is it as simple as getting a spanner tool and rotating the bottom collar?

DMC-81
03-21-2017, 12:31 AM
Has anyone adjusted the ride height on their AVO rear coilovers that DMC currently sells? Is it as simple as getting a spanner tool and rotating the bottom collar?

Hi there, I have. It's better if you compress the spring a bit to relieve pressure on the collar. That way, you don't need a spanner.

Gregadeth
03-21-2017, 02:06 AM
Hi there, I have. It's better if you compress the spring a bit to relieve pressure on the collar. That way, you don't need a spanner.Thanks! Good to know. How about without having to compress the springs? I'd like to avoid using spring compressors. I would probably only be changing the height about half an inch, so not a lot.

Josh
03-21-2017, 03:13 AM
It kind of defeats the purpose of adjustablity a little if you feel the need to compress the springs. But I will agree it makes it easier.
You can certainly adjust them just with a spanner. Coilover type shock/spring assemblies are very common in many other automotive crowds and it does not cause any problems.

Bitsyncmaster
08-27-2017, 08:02 PM
My drivers side shock started leaking oil (Hervey's easy rider) so I replaced it with a NOS shock and it fixed the drop (drivers side was lower than passenger side.

Josh
08-28-2017, 02:12 AM
My drivers side shock started leaking oil (Hervey's easy rider) so I replaced it with a NOS shock and it fixed the drop (drivers side was lower than passenger side.

Im thinking it was the collar sliding on the shock body causing the drop.

Bitsyncmaster
08-28-2017, 06:54 AM
Im thinking it was the collar sliding on the shock body causing the drop.

There was no evidence the collar moved.

Drive Stainless
08-28-2017, 10:23 AM
Did you drive the car since replacing the shock?

Bitsyncmaster
08-28-2017, 10:46 AM
Did you drive the car since replacing the shock?

No. I just let it down on the wheel and bounced the rear end a little.

Josh
08-28-2017, 11:34 AM
if you drive it you will find it settles a bit.

The springs determine the height, the shocks just dampen.

Nicholas R
08-28-2017, 11:54 AM
if you drive it you will find it settles a bit.

The springs determine the height, the shocks just dampen.

Agreed. Shocks have nothing to do with ride height; they only affect the rate at which the springs can be loaded and unloaded.

The only exception is that at the equilibrium point, stiff shocks can bear a small bit of load in either direction, either leaving the spring just slightly extended or compressed as the minimal spring pressure on them isn't enough to move the shock (but it's only momentary). This is why on my car for instance, when I cant get a jack or lift arm under the rear jack point (due to being lowered), I can usually physically grab and lift from the quarter panel, unload the suspension slightly, and set it back down gently with it stopping at a taller height (usually enough to now get the jack or lift arm under it). Aside from this, the true ride height is solely based on the spring rate and free length.

Bitsyncmaster
08-28-2017, 01:28 PM
There is a little extended pressure of the shocks. I would not think it's enough to change the height. The NOS shock was quite a bit to compress. The bad shock had almost zero pressure.

David T
08-28-2017, 02:00 PM
There is a little extended pressure of the shocks. I would not think it's enough to change the height. The NOS shock was quite a bit to compress. The bad shock had almost zero pressure.

Shocks do not affect height unless you have a spring on the shock. Often they are adjustable so yo can make the spring tighter or looser and that would affect height. When replacing a bad shock you ALWAYS replace them in pairs, either both fronts or both rears. Even if only one is bad.

Bitsyncmaster
08-31-2017, 09:28 PM
Well I installed the other shock (passenger side), took the car for a drive and took measurements. The drivers side is still a 1/4 inch lower but you don't really see it like the 1/2 inch I had before. Maybe if I had a passenger on my drive both sides would match.

Anyway, the bad shock had no extension pressure (it would stay fully collapsed). The passenger side still has a lot of pressure to keep it extended.

David T
08-31-2017, 10:42 PM
Where are you measuring that you are 1/2" off? You have to be careful, the body may not be on right and your measurements would be off. Measure from the frame to the ground for the most accurate ride height.