View Full Version : Electrical Radiator fans - anyone know what this one might be?
Timebender
10-01-2016, 06:22 PM
As most of you know, my car has a modded setup with a 350 Chevy, and bigger radiator. Thus the fans aren't stock as far as I know. There's the driver side one, which is big, and the passenger one which is a little smaller. In any case, the passenger one is bad, it runs too slow and causes the circuit breaker to trip, thus no fans, and overheating ensues.
For now, I've disconnected it and all is good - the driver side one runs well and draws a lot of air which is great, but I want to replace the fan or even the motor if possible.
Has anyone seen this used anywhere else, or know where I might find a replacement motor (which detaches with 4 screws), vs. replacing the fan?
http://dmctalk.org/attachment.php?attachmentid=46422&d=1475356874
http://dmctalk.org/attachment.php?attachmentid=46423&d=1475356892
mr_maxime
10-01-2016, 06:34 PM
Can you tell us what radiator the car is from? That might help.
Timebender
10-02-2016, 02:30 PM
I haven't the vaguest idea. I'm the third owner, and the mod was done by the original owner back in the Illinois area,but I'm having no luck tracking him or maybe any family members down. His name is/was: Richard J. Balaguer, in Dundee, and did belong to the DOA. It would be nice to find someone who knows the history of my car.
Greg
mr_maxime
10-02-2016, 02:33 PM
I googled PM3801 and didnt come up with anything useful
No idea how to source just the 12V motor such that it will fit the existing fan blade and the motor mount/brace. And have similar RPM/power vs old motor.
Recommend you go for a new fan + housing. With luck you can get something with a fan shroud for better flow control.
Try Summit Racing for your shopping pleasure. You can down-select for housing ht, width, thickness, fan dia. and more: LINK: Summit Fans Page (https://www.summitracing.com/search/department/cooling-heating/section/fans/part-type/fans-electric/universal/yes?N=4294950709%2B4294949186%2B4294949187%2B42949 51518&SortBy=Default&SortOrder=Default)
In your last photo do we see a mounting bolt for the fan going through the radiator, between the tubes? Whatever works....
DMCVegas
10-02-2016, 09:16 PM
What does the front of that fan look like? Is it held in place with a clip, or perhaps multiple bolts? It almost looks like a Flex-a-lite universal fan that someone removed from the shroud, and then just bolted in place.
If nothing else, if you *really* want to save it, you could always see if an shop that services electrical motors will rebuild it.
Timebender
10-02-2016, 11:45 PM
What does the front of that fan look like? Is it held in place with a clip, or perhaps multiple bolts? It almost looks like a Flex-a-lite universal fan that someone removed from the shroud, and then just bolted in place.
If nothing else, if you *really* want to save it, you could always see if an shop that services electrical motors will rebuild it.
From the back it where I can see it, it's mounted to what it looks like is bolts coming through the radiator. So yes, I could take the motor off and see if I can get it fixed or fix it myself, or find a new fan that's shrouded that has it's mount holes in the same location so I can just bolt it back on.
I have to get it back on a lift, or maybe back it into my garage, then pull it out enough to get up under there, as my garage entrance does slope down enough.
I've tried to drive it up onto some ramps, but because the car rides so low, the air dam acts like a scoop and just pushes them out of the way.
DMC5180
10-04-2016, 12:33 AM
The brand or model part number may be on the front or other non visible parts of the motor. Your going to need to remove the assemble to check that stuff.
Sent from my iPhone using Tapatalk
DMCVegas
10-04-2016, 01:23 PM
From the back it where I can see it, it's mounted to what it looks like is bolts coming through the radiator. So yes, I could take the motor off and see if I can get it fixed or fix it myself, or find a new fan that's shrouded that has it's mount holes in the same location so I can just bolt it back on.
I have to get it back on a lift, or maybe back it into my garage, then pull it out enough to get up under there, as my garage entrance does slope down enough.
I've tried to drive it up onto some ramps, but because the car rides so low, the air dam acts like a scoop and just pushes them out of the way.
Sorry, I should have been more clear on that one. I was trying to ask what the face of the fan blades looked like.
If you've got some ramps but the car is too low, best thing to probably do is to jack up your car on the side, and slide the ramps in under the tires.
Question: Same dimensions on radiator as stock?
Wrong ramps for your setup.
Try something with a lower angle, like the race ramps HERE (https://raceramps.com/ramp-category/garage-and-service-ramps/)
Their Car Service Ramps come 5 different ways, in two low angles, several heights. At least one style will definitely work on your car.
I've tried to drive it up onto some ramps, but because the car rides so low, the air dam acts like a scoop and just pushes them out of the way.
FABombjoy
10-04-2016, 10:11 PM
I would just measure the fan and replace it with another same size unit. Since you're running without a shroud there are numerous universal mounting solutions.
Timebender
10-07-2016, 07:49 PM
Sorry, I should have been more clear on that one. I was trying to ask what the face of the fan blades looked like.
If you've got some ramps but the car is too low, best thing to probably do is to jack up your car on the side, and slide the ramps in under the tires.
Question: Same dimensions on radiator as stock?
Good question. I don't know what the stock ones look like, as I bought the car way after it was modified- waaaay after. I do know it fits width wise- maybe a tad wider, but much taller as they cut out part of the trunk liner to get it to fit.
Timebender
10-07-2016, 07:50 PM
Wrong ramps for your setup.
Try something with a lower angle, like the race ramps HERE (https://raceramps.com/ramp-category/garage-and-service-ramps/)
Their Car Service Ramps come 5 different ways, in two low angles, several heights. At least one style will definitely work on your car.
Good to know!
Timebender
10-07-2016, 07:51 PM
I would just measure the fan and replace it with another same size unit. Since you're running without a shroud there are numerous universal mounting solutions.
Agree- kinda was hoping to just pull off the motor and out on another for ease.
Bitsyncmaster
10-07-2016, 08:30 PM
I have two new fan motors I bought a long time ago. But without knowing how your fan attaches and the distance of the mounting holes I would not know if those would work for you.
Timebender
10-07-2016, 11:40 PM
If I can get under the car I can check for distance. The motor mounts with 4 slotted screws. http://uploads.tapatalk-cdn.com/20161008/e27af3ab54daa0d83f26beed75eb5acd.jpg
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.